Table of Contents 1.0 Purpose..................3 2.0 General Requirements, Warnings and Limitations....4-5 2.1 General Requirements 2.2 System Warnings and Limitations 3.0 System Diagram & Components, Assembly and Installation..5-10 3.1 Techline HLL System w/Cross-Arm Straps........ 6-7 3.2 Techline Residential HLL System w/RA30-2 Roof Anchors..8-10 4.0 Training..................
Us er In stru ctio ns - Engli sh Thank You Thank you for your purchase of Miller fall protection equipment manufactured by Honeywell Safety Products. Miller brand products are produced to meet the highest standards of quality at our ISO...
Do not exceed this weight. Miller TechLine Horizontal Lifeline Systems Capacity ratings assume the anchorage are designed for use with Honeywell-approved or structure to which the horizontal components. Substitution or replacement with lifeline kit is installed meets the load non-approved component combinations, sub- requirements.
SYSTEMS not located directly above the point at which a worker falls. See 6.0 Fall Clearance for A Honeywell-approved full-body harness further explanation and additional warnings and shock-absorbing lanyard, self-retracting related to swing falls.
Us e r I ns tr uc ti o ns - En g l is h 3.1 TechLine HLL System w/Cross-Arm Straps (Complete system diagram shortened for illustration purposes) A. CROSS-ARM STRAPS Used to secure lifeline to - Cross-Arm anchorage point. Straps B.
Page 7
DO NOT continue to tighten the tensioner. Step 5 Close the tension release lever to prevent unintentional loosening of line tension. provided on the horizontal lifeline. Use only connecting devices with compatible locking snap hooks, auto-locking carabiners, or other Honeywell-approved connectors.
Us er In stru ctio ns - Engli sh 3.2 TechLine Residential HLL System w/RA30-2 Roof Anchors (Complete system diagram shortened for illustration purposes) A. RA30-2 ROOF ANCHORS Used to secure lifeline to - RA30-2 Roof anchorage point. Anchors B. SNAP HOOK Self-locking snap hook used to connect the end of the lifeline to an approved anchorage...
Page 9
Us er In stru ctio ns - Engli sh Assembly and Installation Step 1 Install a roof anchor at each approved an- chorage point for the system installation. Read warnings and limitations with regard to roof anchor installation, and follow installation instructions below. RA30-2 Roof Anchor Warnings and Limitations must be installed at least 6 ft.
Page 10
Once slippage occurs, DO NOT continue to tighten the tensioner. Step 5 Close the tension release lever to prevent unintentional loosening of line tension. Use only connecting devices with compatible locking snap hooks, auto-locking carabiners, or other Honeywell-approved connectors.
Us er In stru ctio ns - Engli sh 4.0 Training It is the responsibility of the user and the purchaser of this equipment to assure they are familiar with these instructions and are trained in the proper use, installation, operation, maintenance and limitations of this product.
Cross-Arm Straps and the Techline HLL System with RA30-2 Roof Anchors based on the installation height of the system (above working surface vs. working surface level). If you have any questions about the fall clearance warnings and information provided in this section, please contact Honeywell Technical Service immediately at 800.873.5242 (press 4).
Page 13
Us er In stru ctio ns - Engli sh FALL CLEARANCE DIAGRAM FALL CLEARANCE DIAGRAM (For illustration purposes only; Techline HLL System with cross-arm straps shown) (For illustration purposes only; Techline HLL System with cross-arm straps shown) TECHLINE HLL SYSTEM w/ CROSS ARM STRAPS FALL CLEARANCE TABLES Total Fall Clearance Required for Total Fall Clearance Required for...
Page 14
Us er In stru ctio ns - Engli sh Total Fall Clearance Required for one or two workers connected to system with Miller self-retracting lifeline (SRL) or Miller rope grab and vertical lifeline. Span 1 Worker 2 Workers Length (in Feet)* 0-10 14’-1”...
Non-repairable components that do not pass inspection must be disposed of in a manner to prevent inadvertent further use. Contact Honeywell Technical Service at 800.873.5242 if you have any questions.
Product Labels Étiquettes sur les Produits Etiquetas de los Productos...
Page 17
L930 REV. A 08/15/10 Honeywell Safety Products Franklin, PA USA 800-873-5242 INSTALLATION Attach anchor with eight (8) 5/16” x 2-1/2” or longer lag screws. Position so that fasteners attach to a support structure. LAG SCREWS Heavy-Duty Multiple-Use Roof Anchor ROOF PEAK...
En cas de problème sur un produit, nous contacter au 800-873-5242. ® En Honeywell Safety Products y sus predecesores, hemos estado brindando la calidad de la marca Miller en equipos de protección de caída a millones de trabajadores alrededor del mundo desde 1945.
Page 20
Toll Free: 800.873.5242 Fax: 800.892.4078 Download this manual at: www.millerfallprotection.com Téléchargez ce manuel à l’adresse: www.millerfallprotection.com Puede bajar por Internet este manual en: www.millerfallprotection.com Honeywell Safety Products P.O. Box 271, 1345 15th Street Franklin, PA 16323 USA...