Advertisement
Quick Links
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to
Wear eye
instructions
protection
1. safety
Warning! ensure that Health & safety, local Authority regulations and general workshop practice regulations are adhered to
‰
when using tyre changer. read and fully understand instructions and safety labels attached to machine.
Wear appropriate Personal Protective equipment. A full range of Personal Protective equipment is available from your sealey stockist.
9
Wear suitable clothing to avoid snagging. Do not wear jewellery. tie back long hair.
9
maintain tools to ensure that they are in an adequate condition for safe use and optimum performance.
9
Do not use tyre changer assist arm if damaged.
8
this machine should only be operated by trained personnel.
9
This machine should only be used for the purpose for which it is intended and not modified in any way.
9
Warning! the warnings, cautions and instructions in this manual cannot cover all possible conditions and situations. the operator/
9
user must apply caution and common sense.
2. introDuction
the assist arm is a must have for mounting and dismounting low profile and run flat tyres and is for use in conjunction with Model No. TC10 Tyre
changer. operated by air supply from tyre changer. single air ram operates three separate arms with one control lever. see sealey website for
demonstration video.
3. specification
model no ..................................................................... TC10A
Height ...................................................................... 1220mm
Height when mounted .............................................. 1550mm
operating pressure ............................... 8-10bar (115-145psi)
Weight ............................................................................ 72kg
4. positioning anD assembly
4.1.
Remove packaging and check contents according to the accessory list and fig.1. Clean for assembly. The assembled appearance is
as shown in the fig.2.
fig.1
AccessorY list:-
1. Ø8PU hose
2. Ø8 Y-Tee
3. Plate
4. Cushion
5. Screw M10X130 (nut,flat washer) 4sets
6. Screw M10X25 (nut,flat washer) 2sets
7. Screw M10X20(flat washer) 2sets
8. fix plate
9. tool box.
© Jack sealey limited
instructions for
tyre changer - assist arm for tc10
model no:
Wear protective
Wear safety
gloves
footwear
fig.2
fig.2 Key
1. Roller Arm - to push down on the top bead of the tyre. Used when removing
and fitting the tyre.
2. Disc Arm - to push up the bottom tyre bead. Used when removing the tyre.
3. Bead Holding Arm - to hold the top bead in position when fitting so tyre bead
does not slip off. Used when fitting the tyre.
Original Language Version
tc10a
Wear ear
Wear protective
protection
clothing
crushing of
hands hazard
tC10A | Issue 1 06/02/18
Advertisement
Related Manuals for Sealey TC10A
Summary of Contents for Sealey TC10A
- Page 1 2. introDuction the assist arm is a must have for mounting and dismounting low profile and run flat tyres and is for use in conjunction with Model No. TC10 Tyre changer. operated by air supply from tyre changer. single air ram operates three separate arms with one control lever. see sealey website for demonstration video. 3. specification model no ..............TC10A Height ..............
- Page 2 First, place the cushion fig.1.4 on the indicated position on the steel plate fig.3 and align the 4 holes of the cushion. 4.1.2. Position the body of the assist arm on the cushion and use the bolts fig.1.5 to fix See fig.4, fig.5, fig.6. 4.1.3. Remove the hose from the end of the air source fitting and use a small section of the Ø8PU hose to connect the tee with the outlet as shown in fig.7. fig.5 fig.6 4.1.4. Insert one end of the Ø8PU hose fig 1.1 into the Y Tee and another end connected with the inlet of the pressure adjust valve of the assist arm. 4.1.5. Use part fig.1.7. to fix the part fig.1.8 on the corresponding position on the assist arm column and tighten. Use part fig.1.6 to fix the part fig.1.9 together with the part fig.1.8 and tighten fig.8. fig.7 fig.8 4.1.6. Adjust the assist arm column to ensure that it is vertical: Loosen/tighten bolts fig.1.5 to adjust the column to the vertical. After adjustment, tighten all four bolts. fig.9 fig.10 Original Language Version tC10A | Issue 1 06/02/18 © Jack sealey limited...
- Page 3 Place the upper tyre bead on the tail of the demount head and then press cylindrical press roller on the tyre to make the upper lip lower than the head of the demounting head, fig.15. Rotate the turntable clockwise. After rotating 90°, use the bead holding arm fi g.16. Keep rotating the tyre until fully mounted. Warning! Take care when inflating Tyre. ‰ fig.16 fig.15 Original Language Version tC10A | Issue 1 06/02/18 © Jack sealey limited...
- Page 4 Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. sealey group, Kempson Way, suffolk business park, bury st edmunds, suffolk. ip32 7ar 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk...