hit counter script
Toro 79370 Operator's Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower
  5. 79370
  6. Operator's manual
Toro 79370 Operator's Manual

Toro 79370 Operator's Manual

36" tiller wheel horse classic garden tractor
Hide thumbs
Table of Contents

Advertisement

Quick Links

Form No. 3326–937
36 Tiller
Wheel Horse Classic Garden Tractor
Attachment
Model No. 79370—Serial No. 230000001 and Up
Operator's Manual
Domestic English (EN)

Advertisement

Table of Contents
loading

Related Manuals for Toro 79370

Summary of Contents for Toro 79370

  • Page 1 Form No. 3326–937 36 Tiller Wheel Horse Classic Garden Tractor Attachment Model No. 79370—Serial No. 230000001 and Up Operator’s Manual Domestic English (EN)

  • Page 2: Table Of Contents

    Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 illustrates the location of the model and serial numbers on the product.

  • Page 3: Safety

    Safety Slope Chart...

  • Page 5: Safety And Instruction Decals

    Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 92–7112 Setup Note: Determine the left and right sides of the machine from the normal operating position.
  • Page 6 DESCRIPTION QTY. Tube—Hydro drive Tube—Gear drive Clamp Cable Clevis—Long Clevis—Short Clevis pin Installing the lift cable and lift lever Cotter pin, 1 inch Trunnion Washer, 3/8 inch Lift lever Bushing Shim washer E-ring Latching plate Latch lever Carriage bolt, 3/8 x 1 inch Assembling the mounting plate Washer, 3/8 inch Lock nut, 3/8 inch...

  • Page 7: Installing The Tiller Hitch And Pulleys

    Installing the Tiller Hitch and Installing the Rear Shield Pulleys 1. Rotate tiller down and hook rear shield into slots at rear of tine shield. Secure with 3 cotter pins (1 inch) (Fig. 3). 1. Tip tiller onto back and support in an upright position. Remove the 3/8 x 5-1/2 inch bolt and the 3/8 x 4-1/2 inch bolt from the tiller gear case (Fig.
  • Page 8 3. Remove the fender\seat pan from the tractor. Top View m–5670 1229a Figure 7 Figure 5 1. Cable tube—gear drive 4. Gear shift 1. Fender\seat pan 2. Carriage bolt 2. Clamp 5. Fuel line 3. Bracket 6. Cable 4. Remove bolts and lock washers securing fuel tank bracket to the top of transmission (Fig.

  • Page 9: Removing The Drawbar

    9. Select correct clevis as follows: Removing the Drawbar 2 inch long clevis: for 8-speed gear drive and 1. Remove snap ring from pin and slide from drawbar and hydrostatic models with oil filter on right side. spacers. Remove hitch from tractor (Fig. 11). 3-1/8 inch long clevis: for hydrostatic models with Note: Save all hardware for use when re-installing hitch.

  • Page 10: Installing The Idler Arm Pulley Assembly

    Note: For 8-speed gear drive and hydrostatic models with oil filter on right side tighten hitch mounting by installing angle spacers positioned along top and rear of axle. 2310 Figure 14 1. Front hole 4. Idler arm assembly 2. Rear hole 5.

  • Page 11: Operation

    4. Set Dial-a-Height to the Mounting Position, and lower attachment lift all the way. Refer to Adjusting Dial-a-Height on page 13. 5. Remove trunnion and slide long link of lift chain under attachment lift arm and hook into lower notch (Fig. 16). Install trunnion into bottom hole of lift lever (Fig.

  • Page 12: Operating The Attachment Lift Lever

    Operating the Warning Power Take Off (PTO) on 2000 and Older Models Tines can throw dirt, debris, and small rocks. The operator or bystander could be injured by flying The power take off (PTO) engages and disengages power to debris. the clutch.

  • Page 13: Adjusting Dial-A-Height

    2. Pull attachment lift lever rearward, to release lift pressure, and push the button on top to release the latch. Move lift lever forward to lower attachment. m–2454 Figure 21 1. Lift lever— UP 2. Lift lever— DOWN m–2514 Figure 20 1.

  • Page 14: Removing The Tiller

    1. For maximum tilling depth and transport lift height 7. Remove second lock nut from spring mounting bolt and locate link of lift chain in the lowest notch of lift lever remove (Fig. 23). (Fig. 22). This position will have the greatest lift effort. 2.

  • Page 15: Maintenance

    Always begin tilling with the slowest ground speed possible. Increase speed if conditions permit. Always use full throttle (maximum engine speed) when tilling. Always engage the power take off (PTO) with tiller in the raised position. Till in long straight passes. Do not make turns while tiller is in the ground, as equipment damage may result.

  • Page 16: Greasing And Lubrication

    Greasing and Lubrication Checking Drive Belt Tension 1. Disengage the power take off (PTO), set the parking Service Interval/Specification brake, and turn the ignition key to off. Remove the key. Check the gear lube level in the gear case after every 25 2.
  • Page 17 6. Install the clutch connector (Fig. 28). 2312 Figure 30 1. Belt guard 3. Bolt, 1/4 x 1/2 inch m–5539 2. Idler bracket 4. Belt guide Figure 28 1. PTO clutch 4. Belt guide 2. PTO stop 5. Clutch connector Replacing the PTO Belt on 2000 and 3.

  • Page 18: Storage

    6. Pull on idler arm spring to relieve tension and route belt Storage around tiller drive pulley, under tiller idler and inside belt guide (Fig. 32). 1. Before long term storage wash the machine with mild 7. Check that belt is properly routed around all pulleys and detergent and water to remove dirt and grime from the belt guide (Fig.
  • Page 20 If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.

Table of Contents