Related Manuals for Toro 79412
Summary of Contents for Toro 79412
- Page 1 Form No. 3436-959 Rev A 50in or 54in Bagger Zero-Turn-Radius Riding Mower Model No. 79412—Serial No. 400000000 and Up *3436-959* A Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
Whenever you need service, genuine Toro parts, or 2 Preparing the Machines equipped with additional information, contact an Authorized Service MyRide............6 Dealer or Toro Customer Service and have the model 3 Installing the Weights........6 and serial numbers of your product ready. Figure 1... -
Page 3: Safety
Towing Safety Safety • Do not attach towed equipment except at the hitch • Become familiar with the safe operation of the point. equipment, with the operator controls, and safety • Follow the attachment manufacturer's signs. recommendation for weight limits for towed •... -
Page 4: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal109-6809 109-6809 1. Crushing hazard of hand—do not remove the whole bagger from the machine; open the bagger top and then remove the bag(s) from the bagger. -
Page 5: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. Preparing the machine equipped with – No parts required MyRide. Bolt (3/8 x 1 inch) Locknut (3/8 inch) Left weight-mounting bracket Right weight-mounting bracket... -
Page 6: Preparing The Machine
Preparing the Machine Installing the Weights No Parts Required Parts needed for this procedure: Bolt (3/8 x 1 inch) Procedure Locknut (3/8 inch) Park the machine on a level surface. Left weight-mounting bracket Engage the parking brake. Right weight-mounting bracket Washer Shut off the engine and remove the key. -
Page 7: Installing The Guards On The Machines Equipped With Myride
Installing the Guards on the Machines equipped with MyRide No Parts Required Procedure Insert the top of the guard under the deck, tilt the guard to slide the guard under the frame and place the guard into the notches. g299192 Figure 4 Castor fork and wheel not shown for clarity. -
Page 8: Installing The Attachment Mount
Secure the guard with the bolts. g308507 Figure 8 g300204 Figure 9 1. Carriage bolt (5/16 x 3/4 2. Locknut (5/16 inch) inch) Installing the Attachment Install the pivot frame to the machine frame as shown in Figure 10. Secure the pivot frame to Mount the machine frame using 2 bolts (5/16 x 1 inch) and 2 locknuts (5/16 inch). -
Page 9: Installing The Latch Rod
Installing the Latch Rod Parts needed for this procedure: Latch rod Hairpin cotter Procedure Install the latch rod with a hairpin cotter (Figure 13). g300206 Figure 11 1. Self-tapping screw (5/16 x 3/4 inch) Install the bent, flared end of a rod into the keyed slot in the left side of the machine frame, and move the rod rearward to seat it in the frame (Figure... -
Page 10: Installing The Bagger Top
Installing the Bagger Top Parts needed for this procedure: Grass Bag Upper bagger tube Pivot bracket Bolt (5/16 x 1 inch) Nut (5/16 inch) Procedure Install the bagger top to the bagger frame. Install the pivot brackets onto the pivot frame (Figure 12). -
Page 11: Installing The Chute
Installing the Chute Parts needed for this procedure: Chute Baffle (50-inch decks only) Procedure g300378 For 54-inch decks, go to Step 3. Figure 16 For 50-inch decks, remove the existing baffle from the machine (Figure 18). Lower the bagger top onto the bags (Figure 17). - Page 12 g299302 Figure 19 50-inch decks only g300377 Figure 21 Rotate the baffle until it makes contact with the mower deck. Pivot the chute back and toward the deck so the chute is flush with the mower deck. Note: Ensure that the retaining hook on the cute is out of the way so the chute opening mounts flush to the deck.
-
Page 13: Connecting With The Discharge Tube
Connecting with the Discharge Tube Parts needed for this procedure: Discharge tube Procedure Slide the curved end of the discharge tube into the opening in the bagger top (Figure 24). g300375 Figure 22 Hook the flexible latch on the chute to the retaining clasp welded on the mower deck (Figure 23). -
Page 14: Operation
Operation Note: Determine the left and right sides of the machine from the normal operating position. WARNING To avoid personal injury, follow these procedures: • Become familiar with all operating and safety instructions in the Operator's g005758 Manual for the mower before using this Figure 25 attachment. -
Page 15: Clearing Obstructions From The Bagger
Removing the Bagger Install the bags by sliding the bag frame hooks onto the retaining brackets. Lower the bagger top onto the bags. CAUTION Failing to remove the front bagger weights Clearing Obstructions from and operating the machine without the bagger attachment may cause an unstable condition the Bagger which could result in a loss of control. -
Page 16: Operating Tips
Operating Tips CAUTION As the bagger fills, extra weight is added to Tips for Bagging the back of the machine. If you stop and start the machine suddenly on hills, you may lose steering control or the machine may tip. Remembering the Size •... -
Page 17: Maintenance
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Inspect the bagger. After the first 10 hours • Clean the bagger. Before each use or daily •... -
Page 18: Inspecting The Mower Blades
Inspecting the Mower Storage Blades Storing the Bagger Inspect the mower blades regularly and whenever a Attachment blade strikes a foreign object. If the blades are badly worn or damaged, install new Note: To prevent rapid deterioration of the bag blades. - Page 19 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.