Reducing The Level Of An Analog Signal; Watching Video And Audio Sources Independently; Using The Sleep Timer; Dimming The Display - Pioneer VSX-82TXS Operating Instructions Manual
Audio/video multi-channel receiver
Hide thumbs
Also See for VSX-82TXS:
- Service manual (10 pages) ,
- Service manual (72 pages) ,
- Service manual (72 pages)
Table of Contents
Advertisement
Using other functions
10
• Note that the setting you make here is stored in
memory, even if you switch off the receiver, so if you
want to record a different input source later, you
must do so with REC SELECT, or by selecting
RECOUT SOURCE.
3
After RECOUT disappears from the display, select
the input source you want to listen to.
This will be heard from the main system without affecting
1
your recording.
Tip
• If you have a digital recorder connected to the
DIGITAL OUT1 (ROOM3) digital output and ROOM
3 is switched on (see Using the multi-room controls
on page 59), you can also select a different input
source for this output while ROOM 3 shows in the
display.
Reducing the level of an analog signal
The input attenuator lowers the input level of an analog
signal when it's too strong. You can use this if you find
the that the OVER indicator is lights often, or you can
hear distortion in the sound.
•
Press ANALOG ATT to switch the input attenuator
on or off.
Watching video and audio sources
independently
You can listen to a sound source and select a different
video source on your TV.
•
While listening to a source, press VIDEO SEL ( VIDEO
SELECT ) to select the video source you want to watch.
Press repeatedly to cycle through the possible video
sources. You can select DVD, TV, SAT, DVR1, DVR2,
VIDEO1, VIDEO2 or OFF (no video signal).
Note
1 • Note that switching the ROOM 2 input source (as explained in Multi-room listening on page 57) also changes the RECOUT input source.
• If RECOUT SOURCE is selected, changing the input source likewise changes the input source used for your recording.
2 The attenuator isn't available with digital sources, or when using the Stream Direct modes.
3 Note that this feature will not work with video sources assigned to either of the HDMI video inputs.
4 You can also switch off the sleep timer simply by switching off the receiver.
68
En
2
SLEEP
VIDEO
ANALOG
SEL
ATT
SR+
DIMMER
S.RETRIEVER
D.ACCESS
CLASS
10
SC
SLEEP
VIDEO
ANALOG
SEL
ATT
SR+
DIMMER
S.RETRIEVER
D.ACCESS
CLASS
+10
DISC
3
Using the sleep timer
The sleep timer switches the receiver into standby after a
specified amount of time so you can fall asleep without
worrying about the receiver being left on all night. Use
the remote control to set the sleep timer.
SLEEP
SR+
D ACCESS
•
Press SLEEP repeatedly to set the sleep time.
30 min
Off
• You can check the remaining sleep time at any time
by pressing SLEEP once. Pressing repeatedly will
cycle through the sleep options again.
Dimming the display
You can choose between four brightness levels for the
front panel display. Note that when selecting sources,
the display automatically brightens for a few seconds.
SLEEP
SR+
D.ACCESS
0
•
Press DIMMER repeatedly to change the brightness
of the front panel display.
Switching the speaker impedance
We recommend using speakers of 8 Ω with this system,
but it is possible to switch the impedance setting if you
plan to use speakers with a 6 Ω impedance rating.
•
With the receiver in standby, press
ON while holding down the SPEAKERS button.
Each time you do this, you switch between the
impedance settings:
• SP 6 OHM – Use this setting if your speakers are
rated at 6 Ω.
• SP 8 OHM – Use this setting if your speakers are
rated at 8 Ω or more.
VIDEO
ANALOG
SEL
ATT
DIMMER
S.RETRIEVER
CLASS
60 min
90 min
4
VIDEO
ANALOG
SEL
ATT
DIMMER
S.RETRIEVER
CLASS
STANDBY/
- Quick Links:
- Troubleshooting
Hide quick links:
Advertisement
Table of Contents
