Yamaha CL5 Reference Manual page 8
Digital
Hide thumbs
Also See for CL5:
- Reference manual (261 pages) ,
- Owner's manual (67 pages) ,
- Supplementary manual (26 pages)
Table of Contents
Advertisement
◆ GAIN/PATCH field
This field enables you to make HA (head amp) analog or digital gain settings. You can also
view the operational status of the head amp.
1
GAIN knob
Sets the analog gain/digital gain of the head amp.
Press the knob to open the GAIN/PATCH 1ch window.
2
GC indicator
Indicates the fixed gain value output to the
network if the Gain Compensation function is turned
on.
3
OVER indicator
Warns you when the signal is clipping.
4
Ø (Phase) indicator
Indicates the status of the phase setting.
5
+48V indicator
Indicates the phantom power (+48V) on or off status for the head amp.
6
HPF ON indicator
Indicates the HPF on/off status of the external head amp.
7
AG-DG LINK indicator
Indicates a link between the analog gain and digital gain of the head amp.
8
Digital/Analog gain value
If analog gain is assigned to the GAIN knob, the digital gain value is shown here. If digital
gain is assigned to the GAIN knob, the analog gain value is shown here.
NOTE
• For an input channel that is patched to an input that has no head amp,
will not be shown. For an output channel,
• If a GAIN KNOB FUNCTION is set to DIGITAL GAIN in the USER SETUP
screen, the digital gain knob will appear for
"HA (head amp)
For details, refer to
1
3
2
audio
5 6 7
1
2, 5, 6,
,
1
7
-
will not be shown.
PREFERENCE
1
2, 5, 6, and 7
, and
will not be displayed.
settings"
(page
29).
◆ PAN/BALANCE field
This field enables you to switch the on/off status of the signal sent from the selected channel
to the STEREO/MONO bus, and adjust the pan and balance.
The view and the function of the controllers in this field vary depending on the type of the
4
selected channel.
When an input channel or MIX channel is selected:
1
TO STEREO PAN knob
Sets the pan position of a signal routed to the
STEREO bus.
Press the knob to open the STEREO/MONO 8ch
8
window. If the ST IN channel is selected, you can
specify whether to view the PAN knob or the
BALANCE knob in this window. For a MIX channel,
the PAN knob will appear if the signal is mono, and the BALANCE knob will appear if the
signal is stereo.
NOTE
• For mono input channels, the pan level is nominal at center and +3dB when panned either left or
right. These levels do not change even if channel link is used.
• For ST IN channels, if the PAN knob is selected, the pan level is nominal when panned either left
or right and -3dB at center. If the BALANCE knob is selected the balance level is nominal at
center and +3dB when panned either left or right. These levels do not change even if channel link
is used.
2
ST/MONO button
Switches the on/off status of a signal sent from the
channel to the STEREO/MONO bus.
If an INPUT/MIX channel is set to LCR mode, the
LCR button appears in location
is an overall on/off switch for the signals sent from
7
and
the channel to the STEREO/MONO bus.
When a MATRIX, STEREO, or MONO channel is selected:
1
BALANCE knob
If the signal on the selected channel is stereo, the
BALANCE knob will appear, enabling you to adjust
the volume balance for the left and right channels.
If the channel signal is monaural, the BALANCE
knob is not shown and cannot be used.
Press the knob to open the TO STEREO 8ch
window.
8
SELECTED CHANNEL section
1
2
.The LCR button
1
2
2
Reference Manual
Advertisement
Chapters
Table of Contents
