Advertisement
RS1.V4
RS102.V3 RS103.V2
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: BEFORE USinG THiS PRODUCT, PLEASE READ THE inSTRUCTiOnS CAREFULLY. MAKE CAREFUL nOTE OF SAFETY inSTRUCTiOnS, WARninGS
AnD CAUTiOnS. THiS PRODUCT SHOULD OnLY BE USED FOR iTS inTEnDED PURPOSE. FAiLURE TO FOLLOW THESE inSTRUCTiOnS MAY CAUSE DAMAGE
AnD/OR PERSOnAL inJURY AnD WiLL inVALiDATE THE WARRAnTY. RETAin THESE inSTRUCTiOnS FOR FUTURE USE.
1. SAFETY inSTRUCTiOnS
WARninG! RiSK OF EXPLOSiVE GASES. Working in the vicinity of a lead acid battery is dangerous because they can
generate explosive gases. It is important to remember that batteries generate explosive gases during normal operation.
WARninG! this equipment contains a sealed, non-spillable lead acid battery. this must be disposed of in accordance with
local regulations.
Read and understand the general safety and operating instructions before use. The following information is intended to help you
keep the product in top working order.
nOTE – The battery in this unit is a consumable item and its ability to accept charge will reduce over time. We will warranty it
against mechanical and electrical defect for a period of one year - this does not cover fair wear and tear.
If the battery is not properly charged before first use, or regularly conditioned, its capacity will diminish. under these circumstances we will
not replace the battery even if it is less than one year old.
You can help prolong the lifecycle of the battery by following a few simple guidelines.
•
Plug in your new roadstart to the mains transformer and make an InItIAL charge lasting 38 hours.
•
Ensure the unit is fully charged before storage.
•
DO nOT leave the roadstart for longer than 2 months without putting it on charge.
•
DO nOT attempt to start a vehicle when the roadstart battery voltage is reduced to less than 7Volts.
•
DO nOT drop or roughly handle the roadstart – this will break or disjoin the battery terminals rendering the battery useless and the
warranty void.
•
DO nOT use any other charger, other than the one supplied, to recharge the battery.
IMPORTANT: Be sure to check the voltage switch of the rs105 is turned to the correct voltage before connecting the cables to the vehicle.
In tHE EVEnt of connEctIon to 24VoLt sYstEM WItH tHE sELEctIon In tHE 12VoLt PosItIon:
•
DO nOT
toucH tHE rotArY sWItcH.
•
DiSCOnnECT
tHE BAttErY AnD LEAVE tHE roADstArt unIt to rEst for At LEAst ½ An Hour.
DAnGER OF EXPLOSiOn iF THESE inSTRUCTiOnS ARE nOT OBSERVED.
IMPORTANT: to reduce the risk of a battery explosion, follow these
instructions and those published by the battery manufacturer and the
manufacturer of any equipment you intend to use in the vicinity of the
battery. remember to review warning marks on all products and on
engines.
1.1
PERSOnAL PRECAUTiOnS
Ensure there is another person within hearing range, or close
enough to come to your aid should a problem arise, when
working near a lead-acid battery.
Have fresh water and soap nearby in case battery acid contacts
skin, clothing or eyes.
Wear safety eye protection and protective clothing. Avoid
touching eyes while working with a battery.
Wash immediately with soap and water if battery acid contacts
skin or clothing. If acid enters eye, flush eye immediately with
cool, clean running water for at least 15 minutes and seek
immediate medical attention.
remove personal metallic items such as rings, bracelets,
necklaces and watches. A lead-acid battery can produce a
short-circuit current high enough to weld a ring or the like to
metal, which may cause severe burns.
1.2
iMPORTAnT SAFETY inSTRUCTiOnS
familiarise yourself with the applications, limitations and potential
hazards of the roadstart.
Keep the unit in good working order and condition. replace
damaged parts immediately.
use only recommended parts. to use unapproved parts may be
dangerous and will invalidate your warranty.
the roadstart must only be opened and checked by qualified
service personnel. DO nOT disassemble the unit for any reason.
Keep children and unauthorised persons away from the work area.
Keep work area clean and tidy and free from unrelated materials.
Ensure that there is adequate lighting.
iMPORTAnT WARRAnTY inFORMATiOn: KEEP YOUR ROADSTART HEALTHY
iMPORTAnT: USE OF RS105:
InstructIons for:
ROADSTART UniTS
RS104.V2
If the roadstart receives a sharp knock or blow, it must be
checked by a qualified service agent before being used.
When not in use re-charge every two months.
DO nOT smoke or allow a spark, or flame in the vicinity of the
battery or engine.
DO nOT drop any metal item onto the battery as it may spark
or short circuit the battery, which could cause an explosion.
DO nOT use roadstart to recharge dry cell batteries that are
commonly used with home appliances. these batteries may
explode and cause personal injury and damage to property.
DO nOT charge or boost a frozen battery.
DO nOT use attachments other than those recommended. to
do so may risk damage to the unit and other equipment and possible
personal injury.
DO nOT pull or carry the unit by its cables and do not pull the
negative and positive clamps from the battery terminals.
DO nOT operate in vicinity of flammable liquids or gases.
DO nOT recharge the unit with plugs, cables or attachments
that are damaged. replace such items immediately.
DO nOT use this product to perform a task for which it is not
designed.
DO nOT store the unit in damp or wet locations or where the
temperature may exceed 50°c.
DO nOT submerge the unit in water.
DO nOT use whilst under the influence of drugs, alcohol or
intoxicating medication.
DO nOT leave the unit in a totally discharged state for an
extended period of time as this may result in permanent damage.
D O nOT cross-connect the power leads from the roadstart to
the battery. Ensure that positive is to positive and negative is to
negative.
Ensure that the unit is fully charged before storage.
Original Language Version
rs1.V4, rs102.V3, rs103.V2, rs104.V2, rs105.V2
RS105.V2
Issue: 5 - 06/01/12
Advertisement
Table of Contents
Related Manuals for Sealey RS1.V4
Summary of Contents for Sealey RS1.V4
- Page 1 RS104.V2 RS105.V2 thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: BEFORE USinG THiS PRODUCT, PLEASE READ THE inSTRUCTiOnS CAREFULLY. MAKE CAREFUL nOTE OF SAFETY inSTRUCTiOnS, WARninGS AnD CAUTiOnS.
-
Page 2: Specification & Features
It is particularly important to use an rcD with portable products that plug into an electrical supply not protected by an rccB. If in doubt consult a qualified electrician. You can obtain a residual current Device through your sealey dealer. You must read and understand instructions concerning electrical safety. -
Page 3: Charging Instructions
Only charge with the adaptor supplied with your specific model. See below. The adaptors are not interchangeable. 3.4.1 RS1.V4 & RS102.V3 use the charger supplied, see fig.7. Plug the Ac charger cable into the charge input socket of the unit. this socket is situated on the back of the unit at the top of the label. -
Page 4: Operation
4.3.7 When the vehicle has started, disconnect the BLAcK (negative -) clamp first from the vehicle chassis. 4.3.8 remove the rED (positive +) clamp from the battery terminal. 4.3.9 return the clamps to the side storage pockets. Original Language Version rs1.V4, rs102.V3, rs103.V2, rs104.V2, rs105.V2 Issue: 5 - 06/01/12... -
Page 5: Questions And Answers
Dispose of batteries according to local authority guidelines. under the Waste Batteries and Accumulators regulations 2009, Jack sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme.