Toro 22317 Operator's Manual
Compact utility loader
Hide thumbs
Also See for 22317:
- Service manual (602 pages) ,
- Operator's manual (44 pages) ,
- Operator's manual (40 pages)
Related Manuals for Toro 22317
Summary of Contents for Toro 22317
- Page 1 Form No. 3354-655 Dingo 220 Compact Utility Loader Model No. 22317—260000001 and Up Operator’s Manual Original Instructions (EN) Register your product at www.Toro.com...
-
Page 2: Table Of Contents
......additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and W 2005 by The Toro Company Contact us at www.Toro.com... -
Page 3: Safety
Safety serial numbers of your product ready. Figure 1 illustrates the location of the model and serial numbers on the product. Improper use or maintenance by the operator or owner can result in injury. To reduce the potential for injury, comply with these safety instructions and always pay attention to the safety alert symbol, which means... - Page 4 • Watch for traffic when operating near or crossing • Use only Toro approved attachments. Attachments can roadways. change the stability and the operating characteristics of • Use extra care when loading or unloading the traction the traction unit.
- Page 5 • Before and while backing, look behind and down for • Battery gases can explode. Keep cigarettes, sparks and small children. flames away from the battery. • Never carry children. They may fall off and be • Keep your body and hands away from pin hole leaks seriously injured or interfere with safe traction unit or nozzles that eject high pressure hydraulic fluid.
-
Page 6: Slope Chart
Slope Chart... -
Page 7: Safety And Instruction Decals
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 98-9051 108-4727 105-8432 98-4682 100-6141... - Page 8 108-9716 94-2551 1. Fast 4. Slow 1. On 3. Off 2. Traction drive 5. Attachment speed 2. Choke 3. Slow 6. Fast 98-8235 1. Fast 3. Slow 2. Traction drive 98-4677 98-8219 1. Fast 3. Slow 2. Throttle...
-
Page 9: Setup
100–9979 1. No fire, open flames, or 5. Read the Operator’s Manual. 9. Wear eye protection; 11. Sulfuric acid can cause smoking. explosive gases can cause blindness or severe burns. 6. Explosion hazard blindness and other injuries 2. Wear eye protection 12. -
Page 10: Installing The Valve Lever
Installing the Valve Lever Warning 1. Remove and discard the nut securing the bolt and washer to the speed selector lever. Battery terminals or metal tools could short against metal components, causing sparks. Sparks 2. Secure the lever to the speed selector valve using the can cause the battery gasses to explode, resulting bolt and washer as illustrated in Figure 2. -
Page 11: Specifications
These attachments allow you to perform many different functions with the traction unit such as hauling materials, digging holes, grading, and more. Contact your Toro dealer for a list of all approved attachments and accessories. Important Use only Toro approved attachments. -
Page 12: Stability Data
Stability Data The following table lists the maximum slope recommended for the traction unit in the positions listed in the table. Slopes over the listed degree may cause the traction unit to become unstable. The data in the table assumes that the loader arms are fully lowered and that the factory installed tires are on the traction unit, inflated to the recommended pressure;... -
Page 13: Before Operating
Before Operating Important Never use methanol, gasoline containing methanol, or gasohol containing more than 10% ethanol because the fuel system could be damaged. Do not mix oil Before operating, check the fuel and oil level, remove with gasoline. debris from the traction unit, and check the tire pressure. Also, ensure that the area is clear of people and debris. -
Page 14: Removing Debris From The Traction Unit
5. Slide the dipstick fully into the dipstick tube (Fig. 4). 6. Remove and store the cylinder locks (refer to Using the Cylinder Locks, page 18), and lower the loader 6. Pull the dipstick out and look at the metal end. arms. -
Page 15: Operation
m–1872 Figure 6 1. Valve stem Operation Note: Determine the left and right side of the machine from the normal operating position. Traction Unit Overview Figure 7 contains a front and back view of the traction unit. Familiarize yourself with all of the traction unit components listed in Figure 7. -
Page 16: Controls
Controls Traction Control Levers To move forward, move the traction control levers Become familiar with all the controls (Fig. 8) before you forward. To move rearward, move the traction control start the engine and operate the traction unit. levers rearward. To go straight, move both traction control levers equally. -
Page 17: Starting And Stopping The Engine
Move the speed selector lever to the rearward position to Important Do not engage the starter for more than 10 set the auxiliary hydraulics to high speed and the traction seconds at a time. If the engine fails to start, allow a 30 drive, loader arms, and attachment tilt to low speed. -
Page 18: Stopping The Traction Unit
Using the Cylinder Locks Note: The farther you move the traction control levers in either direction, the faster the traction unit will move in that direction. Warning Stopping the Traction Unit The loader arms may lower when in the raised position crushing anyone under them. -
Page 19: Installing And Removing Attachments
4. Clevis pin Installing and Removing Attachments Connecting an Attachment Important Use only Toro-approved attachments. Attachments can change the stability and the operating characteristics of the traction unit. The warranty of the traction unit may be voided if used with unapproved attachments. -
Page 20: Securing The Traction Unit For Transport
1. Stop the engine. 3. Disengage the quick attach pins by turning them to the outside. 2. Move the auxiliary hydraulics lever forward, 4. If the attachment uses hydraulics, move the auxiliary backward, and back to neutral to relieve pressure at the hydraulic couplers. -
Page 21: Maintenance
Maintenance Note: Determine the left and right side of the machine from the normal operating position. Recommended Maintenance Schedule Maintenance Service Maintenance Procedure Interval • Change the hydraulic filter After the first 8 hours • Torque the wheel lugnuts to 50 ft-lb (68 N⋅m) After the first 50 hours •... -
Page 22: Greasing The Traction Unit
Greasing the Traction Unit Note: Service the air cleaner more frequently (every few hours) if operating conditions are extremely dusty or sandy. Grease all pivot joints every 8 operating hours and immediately after every washing. Removing the Foam and Paper Elements Grease Type: General-purpose grease. -
Page 23: Servicing The Traction Drive Chains
Servicing the Traction Drive 3. Put one or two ounces of oil on the pre-filter (Fig. 17). Chains Lubricating the Drive Chains Lubricate the drive chain every 50 operating hours. m–1213 Figure 17 1. Lower the loader arms, stop the engine, and remove 1. -
Page 24: Servicing The Engine Oil
6. Adjust the chain tensioning bolt until the distance between the bottom of the chain guard and the lower chain span is within 1–1/2 to 2–1/2 inches (3.8 to 6.35 cm) (Fig. 19). 7. Position the axle retaining bracket tight against the axle and the frame, then tighten the nut on the bolt to secure it in place (Fig. -
Page 25: Replacing The Battery
Replacing the Battery m–3216 When the battery no longer holds a charge, replace it. Figure 21 Important Use only a genuine Toro replacement 1. Oil drain valve 2. Drain hose battery. 7. Remove the old filter and wipe the filter adapter Warning (Fig. - Page 26 2. Stop the engine and remove the key. Warning 3. Remove the wing nut and bolt securing the battery clamp and strip (under the clamp) and remove the Battery terminals or metal tools could short clamp and strip (Fig. 23). against metal components, causing sparks.
-
Page 27: Servicing The Spark Plugs
Servicing the Spark Plugs Check the spark plugs after every 200 operating hours. 0.030 in. Ensure that the air gap between the center and side (0.76 mm) electrodes is correct before installing each spark plug. Use a spark plug wrench for removing and installing the spark plugs and a gapping tool/feeler gauge to check and adjust the air gap. -
Page 28: Replacing The Fuel Filter
Checking Hydraulic Lines 10. Stop the engine and check for leaks. 11. Check the fluid level in the hydraulic tank (refer to After every 25 operating hours, check the hydraulic lines Checking the Hydraulic Fluid, page 14) and add fluid and hoses for leaks, loose fittings, kinked lines, loose to raise the level to mark on dipstick. -
Page 29: Draining The Fuel Tank
Note: Now is the best time to install a new fuel filter because the fuel tank is empty. 6. Install the fuel line onto the fuel filter. 7. Slide the hose clamp close to the fuel filter to secure the fuel line. m–3217 8. - Page 30 B. Run the engine to distribute conditioned fuel through the fuel system (5 minutes). C. Stop the engine, allow it to cool, and drain the fuel tanks; refer to Draining Fuel Tanks, page 29. D. Start the engine and run it until it stops. E.
-
Page 31: Troubleshooting
Troubleshooting Problem Possible Causes Corrective Action Starter does not crank 1. Auxiliary hydraulics lever is not 1. Move lever to neutral position. in neutral position. 2. Battery is dead. 2. Charge the battery. 3. Electrical connections are 3. Check electrical connections corroded or loose. - Page 32 Problem Possible Causes Corrective Action Traction unit does not drive. 1. Hydro fluid level low. 1. Add hydro fluid to reservoir. 2. Traction pump drive coupler is 2. Contact Service Dealer. loose or broken. 3. Pump and/or wheel motor is 3.
-
Page 33: Schematics
Schematics Electrical Schematic... - Page 34 Hydraulic Schematic...
-
Page 35: Evaporative Emission Control Warranty Statement
Company. Owner’s Warranty Responsibilities: ® As the equipment owner, you are responsible for performance of the required maintenance listed in your Operator’s Manual. The Toro • ® Company recommends that you retain all receipts covering maintenance on your equipment, but The Toro Company cannot deny warranty solely for the lack of receipts. -
Page 36: The Toro Dingo Product Line Warranty
If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.