hit counter script
Toro Z Master Series Setup Instructions
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower
  5. Z Master Series
  6. Setup instructions
Toro Z Master Series Setup Instructions

Toro Z Master Series Setup Instructions

Kubota-powered mowers
Hide thumbs Also See for Z Master Series:
Table of Contents

Advertisement

Quick Links

Kubota-Powered Z Master
for Australia Mowers

Loose Parts

Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
9
10
11
12
© 2009—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Description
No parts required
No parts required
Rear wheels
Roll bar, right section
Roll bar, left section
Roll bar, center section
Bolt, (3/8 x 1 inch)
Curved washer
Flange nut, (3/8 inch)
Bolt, (1/2 x 3–1/4 inch)
Flange nut, (1/2 inch)
No parts required
J-bolt
Wing nut
Hold down clamp
No parts required
Number 2 general purpose lithium base
or molybdenum base grease. (Purchase
separately.)
No parts required
No parts required
No parts required
Operator's Manual
Engine Owner's Manual
Registration Card
Operator training material
Key
Register at www.Toro.com.
Form No. 3361-750 Rev A
Mowers
®
Qty.
–
Remove parts from the crate.
–
Check the tire pressure.
2
Install the drive wheels.
1
1
1
8
Install the Rollover Protection System
(ROPS).
8
8
2
2
–
Add fuel to the machine.
2
2
Install a battery
1
–
Charge the battery.
1 tube
Check the machine for grease.
–
Check the engine oil level.
–
Prepare the side discharge chute.
Check the machine before delivery to
–
the customer.
1
1
1
Delivering the machine to the customer.
1
2
Setup Instructions
Use
Original Instructions (EN)
Printed in the USA.
All Rights Reserved

Advertisement

Table of Contents
loading

Related Manuals for Toro Z Master Series

Summary of Contents for Toro Z Master Series

  • Page 1: Loose Parts

    Operator’s Manual Engine Owner’s Manual Registration Card Delivering the machine to the customer. Operator training material Register at www.Toro.com. © 2009—The Toro® Company Original Instructions (EN) 8111 Lyndale Avenue South Printed in the USA. Bloomington, MN 55420 All Rights Reserved...

  • Page 2: Checking The Tire Pressure

    Removing Parts from the Crate Raising the Machine Up and Installing the Drive Wheels No Parts Required Parts needed for this procedure: Procedure Rear wheels Remove the tires and the parts for the ROPS from the shipping crate. Procedure 1. Remove the screws holding the right angle retaining plate to the crate.

  • Page 3: Installing The Roll Over Protection System

    Figure 4 4. Mount the wheels with the valve stem to the outside and secure them with the wheel nuts previously removed. 5. Torque the wheel nuts to 95 ft-lb (128 N·m). Figure 6 6. Remove the jack-stands. 2. Install the lanyard clips onto the long bolts (1/2 x 3-1/4 inch).

  • Page 4: Adding Fuel To The Machine

    6. Torque all lower fasteners, attached to the machine frame, to 30 ft-lb. 7. Tighten the center roll bar bolts (1/2 x 3-1/4 inch) so it rotates freely with some resistance. Note: No more than one thread should be exposed outside the nut.

  • Page 5: Installing A Battery

    Installing a Battery Parts needed for this procedure: J-bolt Wing nut Hold down clamp Figure 11 Procedure Purchase a 12V battery and install it into the machine. The engine requires a minimum of 540 CCA. Use the hardware included to install the new battery. Refer to Installing the Battery in the Operator’s Manual.

  • Page 6: Checking The Side Discharge Chute

    Checking the Side Discharge Chute No Parts Required Procedure If there are plastic ties holding the side discharge chute up, remove them and lower the chute into place. Figure 13 5. Check the grease for the pump drive belt idler arm. An uncovered discharge opening could allow 6.
  • Page 7 Figure 15 1. Grass Deflector 4. L end of spring, place behind deck edge before installing bolt 2. Spring 5. Deck edge 3. J hook end of spring...
  • Page 8 Checking the Machine Before Delivery to the Customer No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator’s Manual for instructions on performing these procedures.
  • Page 9 Delivering the Machine to the Customer Parts needed for this procedure: Operator’s Manual Engine Owner’s Manual Registration Card Operator training material Procedure At delivery, Fill in the model and serial number and complete the items listed in the following table and initial each when finished.
  • Page 10 Make sure that the customer receives the Operator’s Manual, Engine Owner’s Manual, Set Up Instructions, and operator training material. Make sure the customer knows the Parts Catalog is available at www.Toro.com Assist the customer in loading the mower. Note: When you, the dealer representative, have finished delivering the machine to the customer, sign and date in the space provide below and keep a copy of this page for dealer records.
  • Page 11 Notes:...

Table of Contents