IMPOR TANT NOTICE This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and under- stood by the users, and have therefore not been restated.
EZ-AG CIRCUIT BOARD LAYOUT <Bottom view> Battery cover assembly <Top view> Bottom assembly CN801 CN802 <Bottom view> <Bottom view> Neck assembly CN501 CN601 CN604 CN701 • First lot Strings sensor unit Top assembly MUTE Adhesive connector tape assembly...
Page 6
SENSOR PIEZO UNIT SENSOR CN903 (4P) Earth 9,10 LD90 STRING Plate SW MATRIX S1-S6 MUTE CN902 (4P) 8X10 S [0-11] S [0-11] PIEZO Driver D [0-7] D [0-7] PLATE SPEAKER SENSOR IC1 (64P) L [0-15] L [0-14] 4 Ω TA1,3 7 Seg LED LED MATRIX (18P)
EZ-AG DISASSEMBLY PROCEDURE Caution: Be sure to attach the removed filament tape just as it was before removal. Bottom Assembly AM Circuit Board (Time required: About 2 minutes) (Time required: About 4 minutes) Remove the eight (8) screws marked [110A],the two Remove the bottom assembly.
Page 8
EZ-AG Strings Sensor Unit PN Circuit Board, Key Top Rubber (Time required: About 3 minutes) (Time required: About 4 minutes) Remove the bottom assembly. (See procedure 1.) Remove the bottom assembly. (See procedure 1.) Remove the four (4) screws marked [130B] and the Remove the three (3) screws marked [N100].
EZ-AG LSI PIN DESCRIPTION MN101C027YB (XS711200) CPU PN: IC001 NAME FUNCTION NAME FUNCTION Switch matrix data Switch matrix data MIDI transmit data VREF+ Power supply (+5V, analog) Switch matrix data Power supply (+5V) OSC2 Crystal oscillator (8MHz) OSC1 Crystal oscillator (8MHz)
Page 10
EZ-AG HG73C205AFD (XU947C00) SWX00B (Tone Generator) DM: IC101 NAME FUNCTION NAME FUNCTION Initial clear CMA3 Program address bus RFCLKI PLL Clock CMA8 Program address bus PLL Control CMA2 Program address bus Power supply read signal AVDD_PLL AVSS_PLL Ground CMA1 Program address bus...
EZ-AG TEST PROGRAM Preparation PA-3C, PA-32 (AC adaptor) is used. Jigs: Frequency counter, level meter (with JIS-C filter), MIDI cable Note) Connect a stereo plug to the [PHONES/OUTPUT] jack at 33 ohms. [STANDBY/ON] How to enter the Test Mode While pressing the 1st fret, 2nd fret and 3rd fret of 6th string, turn the [STANDBY/ON] switch on.
Page 17
EZ-AG TEST 7-seg. LED for Each Test Test Function and Judgment criteria Check the switches and the LEDs on the panel. Press the switches as shown on the LEDs in the sequence indicated in TABLE 1 (P.18). A sound is generated while the fret switch is pressed. (No key stick is existed.) Press the [DEMO] button to interrupt operation.
EZ-AG <TABLE1> DEMO SOUND SONG STRUM CHORD BOTH TEMPO VOLUME CAPO 1st fret of 2nd fret of 12th fret of 1st fret of 12th fret of TUNING – 1st string 1st string 1st string 2nd string 6th string 6 11 12...
Page 20
EZ-AG NOTE: EZ-AG functions as a 16-channel multi-timbral tone generator, and incoming data does not affect the panel voices or panel settings. However, the MIDI messages listed below do affect the panel voices and songs. • MIDI Master Tuning Control change <RPN>...
PARTS LIST CONTENTS OVERALL ASSEMBLY ............. 2 STRINGS SENSOR UNIT ............4 ELECTRICAL PARTS ............6-11 Notes : DESTINATION ABBREVIATIONS A : Australian model M : South African model B : British model O : Chinese model C : Canadian model Q : South-east Asia model D : German model T : Taiwan model...
Page 28
EZ-AG PART NO. DESCRIPTION REMARKS REF NO. RANK CN601 VB858800 Connector Base Post PH 9P SE CN604 VB858100 Connector Base Post PH 2P SE CN701 VB858400 Connector Base Post PH 5P SE D0501 VZ060500 Diode SFPB-62V D0502 VV925900 Diode RLS-73 TE-11...