http://www.xiaoyu163.com SAFETY INFORMATION 3 7 63 1515 0 - Service Precautions CD section precaution 1. Before disassembling the unit, be sure to turn off the power. Unplugging and plugging the connectors during power-on mode may damage the ICs inside the unit. 2.
http://www.xiaoyu163.com 3 7 63 1515 0 This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual.
Page 4
http://www.xiaoyu163.com 3 7 63 1515 0 [ Important symbols for good services ] In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely. When you find the procedures bearing any of the symbols, be sure to fulfill them: 1.
http://www.xiaoyu163.com 1. SPECIFICATIONS 3 7 63 1515 0 General UC,EW model Power source ....14.4 V DC (High) Grounding system ..Negative type Frequency ..3.15 k/8 k/10 k/12.5 Max. current consumption k Hz ........10.0 A Q Factor ..0.35/0.59/0.95/1.15 (+6 dB when boosted) Backup current ....
http://www.xiaoyu163.com 3 7 63 1515 0 FM tuner Display Screen size/Aspect ratio 6.5 inch wide/16:9 UC model (effective display area: 146.72 ×79.10 mm) Frequency range ..87.9 – 107.9 MHz Pixels ......336,960 (1,440 ×234) EW,ES model Type ......TFT active matrix, Frequency range ..
http://www.xiaoyu163.com 2. EXPLODED VIEWS AND PARTS LIST 3 7 63 1515 0 OTES : • Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List. • Screw adjacent to mark on the product are used for disassembly. •...
Page 9
http://www.xiaoyu163.com (1) PACKING SECTION PARTS LIST Mark No. Description Part No. 3 7 63 1515 0 Mark No. Description Part No. 17-4 Installation Manual See Contrast table(2) Carton See Contrast table(2) Contain Box See Contrast table(2) 17-5 Caution Card CRP1276 Cord Assy See Contrast table(2) 17-6 Passport...
http://www.xiaoyu163.com 2.5 CD MECHANISM MODULE 3 7 63 1515 0 GEM1030 GEM1030 L 13942296513 GEM1029 u163 AVH-P6400CD/UC http://www.xiaoyu163.com...
Page 17
http://www.xiaoyu163.com CD MECHANISM MODULE SECTION PARTS LIST Mark No. Description Part No. Mark No. 3 7 63 1515 0 Description Part No. CD Core Unit CWX2676 Arm Unit CXB4503 Connector(CN101) CKS3785 Motor Unit(M3) CXB6620 Connector(CN901) CKS4291 Screw(M2x1.2) CBA1495 Connector(CN701) CKS4522 Guide CNV5925 Screw...
http://www.xiaoyu163.com 3.4 MOTHER PCB(GUIDE PAGE) 3 7 63 1515 0 Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST". Large size SCH diagram Guide page Detailed page CN701 13.7V L 13942296513 CN2402 u163...
http://www.xiaoyu163.com 3.11 CD MECHANISM MODULE 3 7 63 1515 0 CD CORE UNIT PICKUP UNIT(SERVICE)(P8) RF AMP 8200P CARRIAGE MOTOR M1 CXB6361 L 13942296513 BLACK WHITE ACT / MOTOR DRIVE SIGNAL LINE FOCUS SERVO LINE TRACKING SERVO LINE CARRIAGE SERVO LINE SPINDLE SERVO LINE SWITCHES: CD CORE UNIT...
http://www.xiaoyu163.com 4. PCB CONNECTION DIAGRAM 3 7 63 1515 0 4.1 MOTHER PCB NOTE FOR PCB DIAGRAMS MOTHER PCB 1.The parts mounted on this PCB include all necessary parts for several destination. For further information for respective destinations, be sure CN4801 to check with the schematic dia- gram.
Page 47
http://www.xiaoyu163.com 3 7 63 1515 0 SIDE A L 13942296513 u163 CN3831 FRONT AVH-P6400CD/UC http://www.xiaoyu163.com...
Page 49
http://www.xiaoyu163.com 3 7 63 1515 0 SIDE B FAN MOTOR M1 CN1801 POWER SUPPLY TERMINALS L 13942296513 CN701 u163 AVH-P6400CD/UC http://www.xiaoyu163.com...
http://www.xiaoyu163.com 4.2 TUNER PCB 3 7 63 1515 0 SIDE A SIDE B TUNER PCB TUNER PCB IP-BUS AV BUS L 13942296513 CN1341 u163 AM/FM ANTENNA AVH-P6400CD/UC http://www.xiaoyu163.com...
http://www.xiaoyu163.com 4.4 INVERTER PCB 3 7 63 1515 0 SIDE A SIDE B INVERTER PCB INVERTER PCB L 13942296513 u163 BACK LIGHT AVH-P6400CD/UC http://www.xiaoyu163.com...
http://www.xiaoyu163.com 4.5 RELAY PCB,UPPER PCB 3 7 63 1515 0 SIDE A SIDE B RELAY PCB RELAY PCB CN1331 CN2804 L 13942296513 UPPER PCB SIDE A UPPER PCB SIDE B u163 AVH-P6400CD/UC http://www.xiaoyu163.com...
http://www.xiaoyu163.com 4.7 ENCODER UNIT 3 7 63 1515 0 ENCODER PCB SIDE A CN4803 L 13942296513 ENCODER PCB SIDE B u163 AVH-P6400CD/UC http://www.xiaoyu163.com...
Page 57
http://www.xiaoyu163.com 3 7 63 1515 0 SW PCB SW PCB SIDE B SIDE A DEG0 CN2806 L 13942296513 u163 AVH-P6400CD/UC http://www.xiaoyu163.com...
http://www.xiaoyu163.com 4.8 CD MECHANISM MODULE 3 7 63 1515 0 SIDE A CD CORE UNIT L 13942296513 u163 AVH-P6400CD/UC http://www.xiaoyu163.com...
Page 59
http://www.xiaoyu163.com 3 7 63 1515 0 SIDE B CD CORE UNIT M2 LOADING MOTOR M3 SPINDLE MOTOR L 13942296513 CN1251 M1 CARRIAGE MOTOR u163 PICKUP UNIT (SERVICE)(P8) AVH-P6400CD/UC http://www.xiaoyu163.com...
http://www.xiaoyu163.com 5. ELECTRICAL PARTS LIST 3 7 63 1515 0 NOTE: Parts whose parts numbers are omitted are subject to being not supplied. • The part numbers shown below indicate chip components. • Chip Resistor RS1/_S___J,RS1/__S___J Chip Capacitor (except for CQS..) CKS.., CCS.., CSZS..
Page 61
http://www.xiaoyu163.com Circuit Symbol and No. Part Name Part No. Circuit Symbol and No. Part Name Part No. D 1011 Diode 1SS355 D 2474 Diode HZU12(B2) 3 7 63 1515 0 D 1071 Diode Network DA204U D 2475 Diode HZU2R0(B) D 2476 Diode HZU2R0(B) D 1141...
Page 62
http://www.xiaoyu163.com Circuit Symbol and No. Part Name Part No. Circuit Symbol and No. Part Name Part No. R 1015 RS1/16S273J 3 7 63 1515 0 VR941 Semi-fixed 15kΩ(B) CCP1449 R 1031 RS1/16S0R0J VR1061 Semi-fixed 10kΩ(B) CCP1448 R 1032 (UC model) RS1/16S0R0J FU941 Fuse 1.25A 63V DC...
Page 63
http://www.xiaoyu163.com Circuit Symbol and No. Part Name Part No. Circuit Symbol and No. Part Name Part No. R 1287 (UC model) RS1/16S473J 3 7 63 1515 0 R 1155 RS1/4S102J R 1288 (UC model) RS1/16S473J R 1166 RS1/16S223J R 1167 RS1/16S223J R 1289 RS1/16S473J...
Page 64
http://www.xiaoyu163.com Circuit Symbol and No. Part Name Part No. Circuit Symbol and No. Part Name Part No. R 1636 RAB4CQ681J 3 7 63 1515 0 R 1637 RAB4CQ681J R 1862 RS1/16S2701F R 1638 RS1/16S681J R 1863 RS1/16S105J R 1639 RS1/16S681J R 1905 RS1/16S223J R 1906...
Page 65
http://www.xiaoyu163.com Circuit Symbol and No. Part Name Part No. Circuit Symbol and No. Part Name Part No. C 991 CKSRYF104Z25 C 1115 (UC model) CCSRCH101J50 3 7 63 1515 0 C 1116 (UC model) CCSRCH101J50 C 1001 CKSYB475K16 C 1117 (UC model) CKSRYB104K25 C 1002...
Page 66
http://www.xiaoyu163.com Circuit Symbol and No. Part Name Part No. Circuit Symbol and No. Part Name Part No. C 1259 CKSRYB473K50 C 1822 CKSRYB104K25 3 7 63 1515 0 C 1281 (UC model) CCSRCH471J50 C 1301 CKSQYB474K16 C 1823 CKSRYB104K25 C 1302 CKSYB474K16 C 1841 CKSRYB102K50...
Page 67
http://www.xiaoyu163.com Circuit Symbol and No. Part Name Part No. Circuit Symbol and No. Part Name Part No. Q 1842 Transistor 2SC4081 3 7 63 1515 0 IC 941 OZ961IS Q 1843 Transistor 2SD2098 IC 942 TA78L05F IC 945 TC7SH08FU Q 1901 Transistor 2SA1577 IC 1001...
Page 68
http://www.xiaoyu163.com Circuit Symbol and No. Part Name Part No. Circuit Symbol and No. Part Name Part No. D 1284 Diode HZU2R0(B) 3 7 63 1515 0 D 1285 Diode HZU2R0(B) L 1251 Inductor LCTA2R2J2520 D 1286 Diode HZU2R0(B) L 1341 Inductor CTF1306 D 1287...
Page 69
http://www.xiaoyu163.com Circuit Symbol and No. Part Name Part No. Circuit Symbol and No. Part Name Part No. FU1841 Fuse 2.3A 50V DC ICPS2R3 3 7 63 1515 0 FU1861 Fuse 1.6A 63V DC CEK1202 R 1061 RS1/16S822J R 1062 RS1/16S822J FU1931 Fuse 1.6A 63V DC CEK1202...
Page 70
http://www.xiaoyu163.com Circuit Symbol and No. Part Name Part No. Circuit Symbol and No. Part Name Part No. R 1180 RS1/16S0R0J R 1401 RS1/16S472J 3 7 63 1515 0 R 1181 RS1/16S472J R 1403 RS1/16S472J R 1404 RS1/16S101J R 1182 RS1/16S472J R 1405 RS1/16S472J R 1183...
Page 71
http://www.xiaoyu163.com Circuit Symbol and No. Part Name Part No. Circuit Symbol and No. Part Name Part No. R 2401 RS1/16S222J 3 7 63 1515 0 R 1649 RS1/16S473J R 2402 RS1/16S222J R 1650 RS1/16S473J R 1657 RS1/16S104J R 2403 RS1/16S473J R 1660 RS1/16S0R0J R 2404...
Page 72
http://www.xiaoyu163.com Circuit Symbol and No. Part Name Part No. Circuit Symbol and No. Part Name Part No. C 948 CKSRYB332K50 C 1078 CCSRCH330J50 3 7 63 1515 0 C 949 CKSRYB152K50 C 1079 47µF/16V CCH1413 C 952 CKSRYB103K50 C 1081 47µF/16V CCH1413 C 1101...
Page 73
http://www.xiaoyu163.com Circuit Symbol and No. Part Name Part No. Circuit Symbol and No. Part Name Part No. C 1234 CKSQYB225K10 C 1801 1000µF CCH1428 3 7 63 1515 0 C 1802 CKSRYB103K50 C 1235 10µF/16V CCH1442 C 1803 CKSRYB104K25 C 1236 22µF/16V CCH1443 C 1251...
Page 74
http://www.xiaoyu163.com Circuit Symbol and No. Part Name Part No. Circuit Symbol and No. Part Name Part No. C 2455 CCSRCH270J50 Q 132 Transistor 2SA1774 3 7 63 1515 0 C 2456 CCSRCH270J50 C 2457 CCSRCH471J50 Q 133 Transistor 2SC4617 C 2458 CCSRCH471J50 Q 151 Transistor...
Page 75
http://www.xiaoyu163.com Circuit Symbol and No. Part Name Part No. Circuit Symbol and No. Part Name Part No. L 803 Inductor LCKB100K2520 R 111 RS1/16S153J 3 7 63 1515 0 L 804 Inductor LCKB100K2520 R 112 RS1/16S104J L 811 Inductor LCKB100K2520 R 113 RS1/16S681J R 114...
Page 76
http://www.xiaoyu163.com Circuit Symbol and No. Part Name Part No. Circuit Symbol and No. Part Name Part No. R 601 RS1/16S471J CKSSYF104Z16 3 7 63 1515 0 CKSSYF104Z16 R 602 RS1/16S471J CKSSYF104Z16 R 603 RS1/16S471J CKSSYF104Z16 R 604 RS1/16S471J C 10 CKSSYF104Z16 R 605 RS1/16S103J...
Page 77
http://www.xiaoyu163.com Circuit Symbol and No. Part Name Part No. Circuit Symbol and No. Part Name Part No. C 123 CCSRCH470J50 C 843 CSZS100M10 3 7 63 1515 0 C 844 CKSRYF104Z25 C 124 CKSRYF104Z25 C 851 CKSRYB104K16 C 131 CKSYF106Z10 C 132 CCSRCH470J50 C 852...
Page 78
http://www.xiaoyu163.com Circuit Symbol and No. Part Name Part No. Circuit Symbol and No. Part Name Part No. IC 301 TC9495F2 3 7 63 1515 0 RESISTORS IC 401 BA5811FM IC 601 PE5273A IC 801 BA05SFP R 2800 RS1/10S0R0J R 2801 RS1/16S153J Q 101 Transistor...
Page 79
http://www.xiaoyu163.com Circuit Symbol and No. Part Name Part No. Circuit Symbol and No. Part Name Part No. C 325 CCSRCH471J50 3 7 63 1515 0 R 412 RS1/16S154J C 329 CKSRYB223K25 R 413 RS1/16S333J R 602 RS1/16S1502D C 401 CCSRCH271J50 R 603 RS1/16S222J C 402...
http://www.xiaoyu163.com 6.4 MONITOR PCB ADJUSTMENT 3 7 63 1515 0 Notes: Flicker adjustment is needed when monitor PCB is exchanged. - Test mode starting prodeure and operation. 1)The TEST land(EPRTEST) and GND on monitor PCB are made to short-circuit. 2)It shifts to [Flicker adjustment mode] in Power ON. 3)To switch between the adjustment modes, use the MENU button.
http://www.xiaoyu163.com 6.5 MONITOR TEST MODE 3 7 63 1515 0 -EEPROM setting mode [Operations] To enter the setting mode, while keeping the EPRTEST terminal (probe land EPRTSTA) at "Low", turn reset the monitor micro computer. To switch between the adjustment modes, use the MENU button. Flicker adjustment mode Line adjustment 1 mode Line adjustment 2 mode...
Page 88
http://www.xiaoyu163.com [Displays in each mode] 3 7 63 1515 0 In the following figures, the letters and numbers surrounded by a large square are for OSD examples. On the screen, the adjustment names and the settings (or written data) are listed. The settings (or written data) will change when some adjustments are made in each mode.
Page 89
http://www.xiaoyu163.com Notes: The CONTRAST data is [88], and used as refference data for other adjustment items, 3 7 63 1515 0 (3) Line adjustment 2 mode Settings or Adjustment Adjustable name Adjustment item written data range (DEC) Bright (SA22: B7-2) [0 - 63] BRIGHT LINE2...
http://www.xiaoyu163.com 6.6 CD ADJUSTMENT 3 7 63 1515 0 1) Precautions 2) Test Mode • This unit uses a single power supply (+5V) for the reg- This mode is used for adjusting the CD mechanism ulator. The signal reference potential, therefore, is module of the device.
Page 91
http://www.xiaoyu163.com - Flow Chart 3 7 63 1515 0 [ANGLE+]+[BAND]+Acc ON [KEY] Test Mode In Contents Display [SOURCE] Source S-CD [BAND] [EQ] [DISP] [PAUSE] RF AMP Power On Power On New Test Mode Gain switching (F. T. offset is adjusted) (F.
http://www.xiaoyu163.com 6.7 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT 3 7 63 1515 0 • Note : The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mecha- nism module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU unit for the CD mechanism module.
http://www.xiaoyu163.com 6.8 CD TEST MODE 3 7 63 1515 0 - CD Section Error No. Display If the CD player cannot operate or if it stops when an error occurred in operation, it enters the error mode and dis- plays the cause of the error in numerals. Accordingly, an object of this display is to assist in analysis and repair. (1) Display example Err XX (2) Error codes...
Page 95
http://www.xiaoyu163.com - CD Section Test Mode (Aging Operation and Setup Analysis) 3 7 63 1515 0 Play is performed in the CD normal mode. However, after setup, in the protection operation, such as FOK (focus), LOCK (spindle), subcodes. sound skip and mechanical-unit errors, the error occurrence and a timeout, the occur- rence cause and occurrence time are displayed.
Page 96
http://www.xiaoyu163.com (4) Operation status display during setup 3 7 63 1515 0 Status No. Description Protection operation CD + 5 V ON is being processed. None SERVO LSI is being initialized (1/3). None CRAM of servo LSI is being initialized. None SERVO LSI is being initialized (2/3).
http://www.xiaoyu163.com 7. GENERAL INFORMATION 3 7 63 1515 0 7.1 DIAGNOSIS 7.1.1 DISASSEMBLY Removing the Case (Fig.1) Case Remove the six screws. Remove the screw and then remove the Case. Removing the Grille Assy (Fig.1) Remove the two screws. Disconnect the connector and then remove the Grille Assy.
Page 99
http://www.xiaoyu163.com 3 7 63 1515 0 Removing the Mother PCB (Fig.3) Remove the solder and then Straight the tab at location indicated. Straight the tabs at two locations indicated. Remove the screw. Remove the screw. Disconnect the connector and then remove the Mother PCB.
Page 100
http://www.xiaoyu163.com 3 7 63 1515 0 Removing the Monitor Assy Holder and Cover Remove the four screws. (Fig.5) Remove the screw and then remove the Holder and Cover. (Fig.5) Remove the Gear. (Fig.6) The Monitor Assy Becomes such a condition. Pull out the Monitor Assy.
Page 101
http://www.xiaoyu163.com 3 7 63 1515 0 Case Unit - Cautions for disassembling and reassembling 1. When pulling chassis and case unit apart, remove Chassis gear, remove five screws, and then remove set of shaft unit before sliding case unit out. When reassembling, the switch on the SW PCB become caught by the parts, so keep the two screws of B as well as the SW PCB removed while reinstalling the case unit.
Page 102
http://www.xiaoyu163.com 3 7 63 1515 0 The numeral enclosed by a circle in the drawing indi- cates the order of removal. - How to hold the mechanism unit 1. Hold the top frame and main frame. 2. Do not hold the front of the top frame tightly because its strength is low.
Page 103
http://www.xiaoyu163.com - How to remove the loading arm assy and spin- 3 7 63 1515 0 dle motor 1. Remove the E ring of the left fulcrum and remove Spindle Motor the spring and loading arm assy. Loading Arm Assy 2.
Page 104
http://www.xiaoyu163.com - How to remove the carriage motor assy 3 7 63 1515 0 Core Unit 1. Remove the solder of the carriage motor lead wire. 2. Remove the grease cover screw and remove the grease cover. Grease Cover 3. After having removed the lead wire processing of the motor, remove the mounting screw of the carriage motor assy.
Page 108
http://www.xiaoyu163.com 3 7 63 1515 0 *TC7S14FU IN_A OUT_Y IC's marked by * are MOS type. Be careful in handling them because they are very liable to be damaged by electrostatic induction. NJM2058V NJM4558E L 13942296513 NJM2137V BA00AST Reference voltage u163 AVH-P6400CD/UC http://www.xiaoyu163.com...
Page 110
http://www.xiaoyu163.com 3 7 63 1515 0 *TC90A64AF 1 42 1 1 4 1 10 VD D DRAM Vss DRAM Vss NGOE Gate Scan Start 1 Test mode3 Gate Scan Start 2 STV1 Test mode2 STV2 Dispaly Mute Gate Clock Out Reset IN Gate Enable Out Control...
Page 111
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Function(PE5291A,PE5290A) Pin No. Pin Name Function and operation BRST P-BUS reset output BSRQ P-BUS request I/O DEGPUL1 AV flap monitor angle sense input DEGPUL2 AV flap monitor angle sense input TESTIN Chip test input MTR1 Storage motor changeover/brake-mode designating output MTR2...
Page 112
http://www.xiaoyu163.com Pin No. Pin Name Function and operation 3 7 63 1515 0 TMUTE RDS tuner mute output Clock adjust output SDBW RDS signal input RECIVE RDS data receive output TSCK Test mode clock input RXN/TSI Data input from navigation Data output to navigation RDS57K RDS 57k signal input...
Page 113
http://www.xiaoyu163.com - Pin Function(PD5747A) 3 7 63 1515 0 Pin No. Pin Name Function and operation Not used REMIN Remote control data input BYTE Outside data select CNVss Mode select VDDSENS Power supply sense 5060IN 50/60Hz input port RESET Reset input Xout Oscillation pin Oscillation pin...
Page 115
http://www.xiaoyu163.com 3 7 63 1515 0 R1130H251B VOUT Current VREF Limit L 13942296513 u163 AVH-P6400CD/UC http://www.xiaoyu163.com...
Page 116
http://www.xiaoyu163.com - Pin Functions (PE5273A) 3 7 63 1515 0 Pin No. Pin Name Format Function and Operation bsck P-Bus serial clock input/output BDATA P-Bus serial data input/output CONT Servo driver power supply control output CDLOAD Load/Eject motor load control output CDEJET Load/Eject motor eject control output Not used (Open)
Page 117
http://www.xiaoyu163.com Pin No. Pin Name Format Function and Operation 3 7 63 1515 0 testin Test program start input SPDLFG FG pulse signal input 74-76 Connected to VDD0 brst P-Bus reset input Connected to VDD0 79,80 Not used (Open) * PE5273A Format Meaning C MOS...
Page 118
http://www.xiaoyu163.com - FM/AM Tuner Unit 3 7 63 1515 0 FM/AM 1ST IF 10.7MHz MPXREF 41kHz AMRF T51 Q51 CF51 CF52 CF53 AMDET AMANT L ch IC 2 FM MPX R ch ANT ADJ COMP MIXER, IF AMP, DET. LDET FMANT RFGND FMRF...
http://www.xiaoyu163.com 7.3.2 MECHANISM DESCRIPTIONS 3 7 63 1515 0 - THE DRIVE MECHANISM SECTION - Electrical criteria - Outlines of the hardwares Sensor signals Encoder pulse Driving Motor DEGPUL1 : Pulse sensor 1 for angular detection The angular adjustment and monitor ejection DEGPUL2 : Pulse sensor 2 for angular detection control (position and angle) motor Sensor signals...
Page 122
http://www.xiaoyu163.com 3 7 63 1515 0 - Ejection Operation 1. When the OPEN/CLOSE key is pressed or when the ACC is turned ON, the motor is driven in a high- speed mode. 2. The motor is driven in a low-speed mode, when the DEG0SW is switched from L to H.
Page 123
http://www.xiaoyu163.com 3 7 63 1515 0 - Angular adjustments 1. When the UP key is pressed, the monitor is raised from its initial position (100 degrees), and will continue to rise until the key is released. The operation will stop one pulse after the release of the UP key.
Page 124
http://www.xiaoyu163.com 3 7 63 1515 0 - Operations of the drive section for each set mode Mode setting Automatic ejection and retraction setting: ON ACC operation mode In OPEN condition During OPEN operation During CLOSE operation In CLOSE condition (Push key) (Automatic) ACC OFF→ON In OPEN condition...
http://www.xiaoyu163.com 7.3.3 OPERATIONAL FLOW CHART 3 7 63 1515 0 - System Control Power ON VDD=5V 19,41pin BSENS 93pin BSENS=L ASENS 92pin ASENS=L Starts communication with monitor microcomputer. 300ms SWACPW←H SWVDD 25pin 500ms L 13942296513 When the timing is according to the above chart, Source keys there is a possibility of a monitor communication failure.
http://www.xiaoyu163.com - Monitor Control 3 7 63 1515 0 Power ON 300ms 500ms VCC=5V When the timing is according to the above chart, 16,62pin there is a possibility of a hideway microcomputer failure. When the timing is not according to the above chart, there is a possibility of a hideway microcomputer failure.
http://www.xiaoyu163.com 8. OPERATIONS 3 7 63 1515 0 - UC model L 13942296513 PAUSE u163 AVH-P6400CD/UC http://www.xiaoyu163.com...
Page 128
NAVI/AV Switches between still picture and button PAUSE/TEXT video entertainment displays. When Press to switch PAUSE function on or this unit is used with a Pioneer off. Navigation Unit, it also switches between navigation and source indi- button cation displays.
PICTURE ADJUST display. ° MENU, TOP, AUDIO, RTN, S.TITLE, ANGLE buttons ) Volume control (–/+) buttons Use when using with a Pioneer DVD component. Press to – or + the volume. · Audio control buttons and DVD control buttons ⁄ Joystick Use to operate AUDIO MENU, select stations etc.