2. Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by electrostatic induction. ND-BT1/E5...
Page 3
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. ND-BT1/E5...
5. ELECTRICAL PARTS LIST ..........................16 6. ADJUSTMENT ............................... 18 6.1 BLUETOOTH TEST MODE........................18 7. GENERAL INFORMATION ..........................22 7.1 DIAGNOSIS ............................. 22 7.1.1 DISASSEMBLY ............................. 22 7.1.2 CONNECTOR FUNCTION DESCRIPTION ..................23 7.2 IC ................................24 8. OPERATIONS ..............................26 ND-BT1/E5...
To remove the #1 screw, use a torques screwdriver(T6)(GGK1072) EXTERIOR SECTION PARTS LIST Mark No. Description Part No. Screw BPZ20T100FTB Cord Assy CDE7963 Cover CNS8686 Case CNS8741 Bluetooth Assy CWN1211 Connector(CN1051) CKS5270 Shield CND3026 Shield CND3027 Insulator CNM9813 Antenna(ANT1001) CTX1095 ND-BT1/E5...
3.2 BLUETOOTH ASSY Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST". BLUETOOTH ASSY BLUETOOTH ANTENNA ND-BT1/E5...
Page 11
No differentiation is made between chip resistors and (NC) (NC) and capacitor fixed values discrete resistors. (NC) (NC) are expressed as : Symbol indicates a capacitor. (NC) DGND ← No differentiation is made between chip capacitors and 0.022 R022 ← GNDE discrete capacitors. ND-BT1/E5...
1.The parts mounted on this PCB include all necessary parts for several destination. For further information for respective destinations, be sure to check with the schematic dia- gram. 2.Viewpoint of PCB diagrams Capacitor Connector SIDE A SIDE B P.C.Board Chip Part CORD ASSY ND-BT1/E5...
R 1001 (A,41,14) RS1/16S681J C 1004 (A,38,32) CKSRYB104K16 R 1002 (A,42,34) RS1/16S0R0J C 1005 (A,39,34) CKSQYB475K6R3 R 1003 (A,40,14) RS1/16S681J R 1004 (A,38,15) RS1/16S103J C 1006 (A,36,32) CKSRYB104K16 R 1006 (A,35,15) RS1/16S103J C 1007 (A,38,37) CEVW100M16 C 1010 (A,27,15) CCSRCH150J50 ND-BT1/E5...
Page 17
(A,18,26) 10 µF CCG1171 C 1043 (A,16,8) CKSRYB105K10 C 1044 (A,19,8) CKSRYB334K10 C 1051 (A,5,32) CEVW100M16 C 1052 (A,9,34) CKSRYB104K16 C 1053 (A,20,35) CEVW100M16 C 1056 (B,13,30) CCSRCH101J50 C 1064 (A,29,5) CKSRYB103K50 C 1081 (B,25,37) CKSRYB104K16 C 1082 (B,21,37) CKSRYB473K50 ND-BT1/E5...
Recommneded mobile phone model; for AVIC-HD1BT/EW5 (ND-BT1/E5) - SonyEricsson S700i/K750i for AVIC-Z1/UC + ND-BT1/E5 - AUDIOVOX SMT5600 Notes: SMT5600 is not possible to transfer whole address book at a time. It can be transfered one by one on this model.
Page 19
OK. * In the case of NOK, possible case is poor connection between ND-BT1/E5 and navigation product or failure of the wired secti- on of ND-BT1/E5. Select [Menu]...
Page 20
If there is a spectrum analyzer supporting 2.4 GHz at the service site, confirmation of transmission carrier becomes possible. Since ND-BT1/E5 cannot operate singly, the AVIC-HD1/EW5 or AVIC-Z1/UC is required. Carrier existence is checked by removing the product case and applying the probe onto the "ANT"...
Page 21
Push [OK] button on the top screen, and take measurement using a spectrum analyzer. Apply a probe to [ANT] land on the PCB, and check if any carrier is displayed at the designated frequency band. Furthermore, make sure that carrier is displayed at each of the three bands. ND-BT1/E5...
7. GENERAL INFORMATION 7.1 DIAGNOSIS 7.1.1 DISASSEMBLY Removing the Case (Fig.1) Case Remove the four screws by tolcs driver (GGK1072) and then remove the Case. Fig.1 Removing the Bluetooth Assy (Fig.2) Remove the solder. Remove the Bluetooth Assy. Bluetooth Assy Fig.2 ND-BT1/E5...