Advertisement
Quick Links
Download this manual
See also:
User Manual
IMPORTANT SAFETY INSTRUCTIONS
Notice to Installers
The servicing instructions in this notice are for use by qualifi ed service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions, unless you are qualifi ed to do so.
Note to System Installer
For this apparatus, the coaxial cable shield/screen shall be
grounded as close as practical to the point of entry of the cable
into the building. For products sold in the US and Canada, this
reminder is provided to call the system installer's attention to
Article 820-93 and Article 820-100 of the NEC (or Canadian
Electrical Code Part 1), which provides guidelines for proper
grounding of the coaxial cable shield.
This symbol is intended to alert you that uninsulated voltage
within this product may have sufficient magnitude to cause
electric shock.Therefore, it is dangerous to make any kind of
contact with any inside part of this product.
Ce symbole a pour but d'alerter toute personne qu'un contact
avec une pièce interne de ce produit, sous tension et non isolée,
pourrait être suffisant pour provoquer un choc électrique. Il est
donc dangereux d'être en contact avec toute pièce interne de
ce produit.
1) Read these instructions.
• Location of the antenna-discharge unit
• Connection to grounding electrodes
2) Keep these instructions.
• Requirements for the grounding electrodes (see the following antenna
3) Heed all warnings.
grounding diagram as recommended by NEC ANSI/NFPA 70)
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
WARNING: Avoid electric shock and fi re hazard! Do not
locate an outside antenna system in the vicinity of overhead
7) Do not block any ventilation openings. Install in accordance
power lines or power circuits. Touching power lines or circuits
with the manufacturer's instructions.
might be fatal.
8) Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding-type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for
Ground Clamps
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
Electric Service
11) Only use attachments/accessories specified by the
manufacturer.
12)
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
NEC = National Electrical Code 1990
National Fire Protection Association
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid
TO CATV INSTALLER
injury from tip-over.
This reminder is provided to call the CATV system installer's attention
to Article 820-40 of the National Electrical Code (NEC) that provides
13) Unplug this apparatus during lightning storms or when
guidelines for proper grounding, and in particular, specifies that the
unused for long periods of time.
cable ground shall be connected to the grounding system of the
building, as close to the point of entry as practical.
14) Refer all servicing to qualified service personnel. Servicing
Protect the Product from Lightning
is required when the apparatus has been damaged in any
way, such as a power-supply cord or plug is damaged,
In addition to disconnecting the AC power from the wall outlet, disconnect
liquid has been spilled or objects have fallen into the
the signal inputs.
apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
Verify the Power Source from the On/Off Power
Light
Power Source Warning
When the on/off power light is not illuminated, the apparatus may still be
A label on this product indicates the correct power source for this product.
connected to the power source. The light may go out when the apparatus is
Operate this product only from an electrical outlet with the voltage and
turned off , regardless of whether it is still plugged into an AC power source.
frequency indicated on the product label. If you are uncertain of the type
of power supply to your home or business, consult your service provider
Eliminate AC Power/Mains Overloads
or your local power company.
The AC inlet on the unit must remain accessible and operable at all times.
Ground the Product
WARNING: Avoid electric shock and fi re hazard! Do not
overload AC power/mains, outlets, extension cords, or integral
convenience receptacles. For products that require battery power
or other power sources to operate them, refer to the operating
instructions for those products.
WARNING: Avoid electric shock and fi re hazard! If this product
connects to coaxial cable wiring, be sure the cable system is grounded
(earthed). Grounding provides some protection against voltage surges
Handling Disposable Batteries
and built-up static charges.
This product may contain disposable batteries. Heed the following warning
and follow the Battery Safety and Battery Disposal instructions below.
Outdoor Grounding System
If this product connects to an outdoor antenna or cable system, be sure
the antenna or cable system is grounded (earthed). This provides some
WARNING: There is danger of explosion if the battery is
protection against voltage surges and built-up static charges.
mishandled or incorrectly replaced. Replace only with the same
type of battery. Do not disassemble it or attempt to recharge it
Article 810 of the National Electric Code (NEC) ANSI/NFPA No. 70-1990,
outside the system. Do not crush, puncture, dispose of in fi re,
provides the following information:
short the external contacts, or expose to water or other liquids.
• Grounding of the mast and supporting structure
Dispose of the battery in accordance with local regulations and
instructions from your service provider.
• Grounding the lead-in wire to an antenna discharge unit
• Size of the grounding conductors
CAUTION: To reduce the risk of electric shock, do not
remove cover (or back). No user-serviceable parts
inside. Refer servicing to qualified service personnel.
WARNING
TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
This symbol is intended to alert you of the presence
of important operating and maintenance (servicing)
instructions in the literature accompanying this product.
Ce symbole a pour but de vous avertir qu'une
documentation importante sur le fonctionnement et
l'entretien accompagne ce produit.
20080814_Installer820
Battery Safety
• Insert batteries correctly. There may be a risk of explosion if the batteries
are incorrectly inserted.
• Do not attempt to recharge 'disposable' or 'non-reusable' batteries.
• Please follow instructions provided for charging 'rechargeable' batteries.
• Replace batteries with the same or equivalent type that we recommend.
• Do not expose batteries to excessive heat (such as sunlight or fi re).
• Do not expose batteries to temperatures above 100°C (212°F).
Battery Disposal
• The batteries may contain substances that could be harmful to the
environment.
• Recycle or dispose of batteries in accordance with the battery
Antenna Lead In Wire
manufacturer's instructions and local/national disposal and recycling
regulations.
• The batteries may contain perchlorate, a known hazardous substance,
Antenna Discharge
Unit
so special handling and disposal of this product might be necessary.
(NEC Section 810-21)
For more information about perchlorate and best management
Grounding
practices for perchlorate-containing substance, see www.dtsc.ca.gov/
Conductors
hazardouswaste/perchlorate
(NEC Section 810-20)
Equipment
Ground Clamps
Provide Ventilation and Select a Location
• Remove all packaging material before applying power to the product.
Power Service
Grounding
• Do not place this apparatus on a bed, sofa, rug, or similar surface.
Electrode System
(NEC Art 250, Part H)
• Do not place this apparatus on an unstable surface.
• Do not install this apparatus in an enclosure, such as a bookcase or rack,
unless the installation provides proper ventilation.
• Do not place entertainment devices (such as VCRs or DVDs), lamps,
books, vases with liquids, or other objects on top of this product.
• Do not block ventilation openings.
Operating Environment
The set-top is designed for operation indoors with a temperature range from
32° to 104° F (0° to 40°C). Each set-top should have adequate spacing
on all sides so that the cooling air vents on the chassis are not blocked.
Protect from Exposure to Moisture and Foreign
Objects
WARNING: Avoid electric shock and fi re hazard! Do not
expose this product to dripping or splashing liquids, rain, or moisture.
Objects fi lled with liquids, such as vases, should not be placed on
this apparatus.
WARNING: Avoid electric shock and fi re hazard! Unplug
this product before cleaning. Do not use a liquid cleaner or an
aerosol cleaner. Do not use a magnetic/static cleaning device (dust
remover) to clean this product.
WARNING: Avoid electric shock and fi re hazard! Never
push objects through the openings in this product. Foreign objects
can cause electrical shorts that can result in electric shock or fi re.
Cisco Explorer 1540C and 1542C Digital-Only
Interactive Set-Tops with Multi-Stream CableCARD
Interface
RNG100
Service Warnings
Declaration of Conformity
This device complies with Part 15 of FCC Rules. Operation is subject
to the following two conditions: 1) the device may not cause harmful
WARNING: Avoid electric shock! Do not open the cover
interference, and 2) the device must accept any interference received,
of this product. Opening or removing the cover may expose you
including interference that may cause undesired operation.
to dangerous voltages. If you open the cover, your warranty will be
void. This product contains no user-serviceable parts.
Check Product Safety
Upon completion of any service or repairs to this product, the service
technician must perform safety checks to determine that this product is in
proper operating condition.
Protect the Product When Moving It
Always disconnect the power source when moving the apparatus or
connecting or disconnecting cables.
20110316_Cable_Safety
Canada EMI Regulation
United States FCC Compliance
This Class B digital apparatus complies with Canadian ICES-003.
This device has been tested and found to comply with the limits for a Class
Cet appareil numérique de la class B est conforme à la norme NMB-003
B digital device, pursuant to part 15 of the FCC Rules. These limits are
du Canada.
designed to provide reasonable protection against such interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy. If not installed and used in accordance with the
instructions, it may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment
OFF and ON, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diff erent from that to
which the receiver is connected.
• Consult the service provider or an experienced radio/television technician
for help.
Any changes or modifi cations not expressly approved by Cisco Systems,
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affi liates in the U.S. and other countries. To view a list of Cisco's trademarks, go to this
Inc., could void the user's authority to operate the equipment.
URL: www.cisco.com/go/trademarks.
The information shown in the FCC Declaration of Conformity paragraph
CableCARD and M-Card are trademarks of Cable Television Laboratories, Inc.
below is a requirement of the FCC and is intended to supply you with
Rovi is a trademark of Rovi Corporation.
information regarding the FCC approval of this device. The phone numbers
listed are for FCC-related questions only and not intended for questions
Other third party trademarks mentioned are the property of their respective owners.
regarding the connection or operation for this device. Please contact your
The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
service provider for any questions you may have regarding the operation or
© 2008, 2011, 2012 Cisco and/or its affi liates. All rights reserved.
installation of this device.
October 2012
DATA
REMOTE
POWER
USB 2.0
AVC VIDEO LICENSE
With respect to each AVC/H.264 product, we are obligated to provide
the following notice:
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO
LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER USES
IN WHICH IT DOES NOT RECEIVE REMUNERATION TO (i) ENCODE VIDEO
IN COMPLIANCE WITH THE AVC STANDARD ("AVC VIDEO") AND/OR (ii)
DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN
A PERSONAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER
Explorer 1540C and 1542C
LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL
Digital-Only Interactive Set-Tops
BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY BE
Model: 1540C and 1542C
OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM.
Manufactured by:
Accordingly, please be advised that service providers, content providers,
Cisco Systems, Inc.
and broadcasters may be required to obtain a separate use license from
5030 Sugarloaf Parkway
MPEG LA prior to any use of AVC/H.264 encoders and/or decoders.
Lawrenceville, Georgia 30044 USA
Telephone: 678 277-1120
ROVI CORPORATION COPYRIGHT
NOTICE
This product incorporates copyright protection technology that is protected
by U.S. patents and other intellectual property rights. Use of this copyright
protection technology must be authorized by Rovi Corporation, and is intended
for home and other limited viewing uses only unless otherwise authorized
by Rovi Corporation. Reverse engineering or disassembly is prohibited.
20081121 FCC Standard
Disclaimer
Cisco Systems, Inc. assumes no responsibility for errors or omissions that
may appear in this guide. We reserve the right to change this guide at any
time without notice.
Cisco Systems, Inc.
5030 Sugarloaf Parkway, Box 465447
Lawrenceville, GA 30042
Printed in United States of America
Quick Reference Guide
678 277-1120
800 722-2009
www.cisco.com
Part Number 78-4020942-01 Rev C
Advertisement
Related Manuals for Cisco Explorer 1540C
Summary of Contents for Cisco Explorer 1540C
- Page 1 WARNING: Avoid electric shock and fi re hazard! Never Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affi liates in the U.S. and other countries. To view a list of Cisco’s trademarks, go to this Inc., could void the user’s authority to operate the equipment.
- Page 2 Welcome Front Panel Installing the Set-Top The Cisco Explorer ® 1540C and 1542C Digital-Only Set-Tops with Multi- 1. Unplug all electronic devices before connecting the set-top. ™ ™ Stream CableCARD (M-Card ) receive and deliver digital signals, and 2. Connect the set-top and VCR or DVD Recorder to the appropriate audio and video inputs as shown in the diagram.