IBM L170 Service Manual SERVICE MANUAL 17” LCD Monitor IBM L170 THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY. EVERY REASONABLE EFFORT HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL; WE CANNOT GUARANTEE THE ACCURACY OF THIS INFORMATION AFTER THE DATE OF PUBLICATION AND DISCLAIMS RE...
IBM L170 Service Manual 1. MONITOR SPECIFICATIONS Driving system TFT Color LCD LCD Panel Size 43.2cm(17.0") Pixel pitch 0.264mm( H )x 0.264mm( V ) Viewable angle 140˚ (H) 120˚ (V) Response time (typ.) 25 ms Video Analog Input Sync. Type...
IBM L170 Service Manual 2. LCD MONITOR DESCRIPTION The LCD MONITOR will contain an main board, an inverter/power board, keypad board and internal adapter which house the flat panel control logic, brightness control logic and DDC. The Inverter board will drive the backlight of panel and the DC-DC conversion.
IBM L170 Service Manual 3. OPERATING INSTRUCTIONS 3.1 GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor. By changing these settings, the picture can be adjusted to your personal preferences.
Page 7
IBM L170 Service Manual Contrast Adjusts over all screen brightness. Brightness Adjusts difference between light and dark areas. Horizontal Position Moves image left or right. Vertical Position Moves image up or down. Automatic Optimizes image(size,position,phase,and clock). Clock Clock Adjusts picture Clock.
IBM L170 Service Manual 4.3 Power Supply Requirements 4.3.1 Input Requirements PARAMETER RANGE CONDITION Input Voltage 100 to 240VAC RMS Universal input full range Input Frequency 60Hz @ 100VAC to 50Hz @ 240VAC Input Current Less than 2.0 Amps RMS Input voltage 100 VAC RMS ;...
IBM L170 Service Manual 4.4.4 Parameter guide line for CCFL Inverter INVERTER MAX BRINGTHNESS (Vadj:5.0v), LOAD=120KΩX4(ROOM TEMPERATURE 25℃ ±4℃) ITEM SYMBOL MIN. TYP. MAX. UNIT REMARK Input voltage Vin 10.8 12 13.2 V Input current Iin 2250 2500 mA FOR 4 LOAD Output Current Iout 6.0 6.5 ...
IBM L170 Service Manual 5.2 Software Flow Chart...
Page 17
IBM L170 Service Manual 1) MCU initialize. 2) Is the eeprom blank ? 3) Program the eeprom by default values. 4) Get the PWM value of brightness from eeprom. 5) Is the power key pressed ? 6) Clear all global flags.
IBM L170 Service Manual 6. Schematic 6.1 Main Board CN101 RX2-IN RX2- A_GND RX2+IN RX2+ SGND Connect two grounds at one single point only. ED101 ED102 SCL_IN C114 C115 DDCCLK SCL_IN SDA_IN 0.1uF/16V(NC) 0.1uF/16V(NC) SDA_IN DDCDAT A_VSYNC D-SUB RX1-IN AGND...
Page 22
IBM L170 Service Manual +T3.3V D3.3V FB204 D3.3V SPEC(60mA) Close to respective power Pins 600OHM C210 C221 C253 C254 C201 C202 C203 C204 C205 C206 C207 C208 C209 47uF/16V 0.1uF/16V 0.01uF 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V...
IBM L170 Service Manual 7.3 Keypad Board 8. Maintainability 8.1 Equirements and Tools Requirement 1.) Voltmeter. 2.) Oscilloscope. 1.) Pattern Generator. 2.) DDC Tool with a IBM Compatible Computer. 3.) Alignment Tool. 4.) LCD Color Analyzer. 5.) Service Manual. 6.) User Manual.
IBM L170 Service Manual 8.2 Trouble Shooting 8.2.1 Main Board 1.NO SCREEN APPEAR Measured U401 pin 2 = 2.5 V? Check Correspondent component. Measured U402 LT1117 pin 2= 3.3V? Is there any shortage or cold solder? Measured CN402 pin 1/2 = 5V? Yes.there have OSD show...
Page 32
IBM L170 Service Manual 2.PANEL-POWER CIRCUIT Check the PPWR panel power relative circuit, check R302 should have response from 0V to 5V Q301, Q302(pin 5,6,7,8) When we switch the power switch from on to off In normal operation, when LED =green, R302...
Page 33
IBM L170 Service Manual 4.U203-DATA OUTPUT NG , no transition Measured DCLK(R240) DVS, DHS (pin 117,116 from U203 ) Is the waveform ok? DCLK around 48 MHZ , DVS=60.09Hz , DHS around 80 KHz ?(refer to input Replace GM5120 /2120 (U203) or signal=640x480@60 Hz 31k, and LED is replace MAINBOARD.
IBM L170 Service Manual 8.2.2 Power/Inverter Board 1.) No power Check to CN102 Pin1 and pin2 = 5V Check Interface board Check AC line volt 120V or 220V Change F901 , check BD901,Q903,IC901 Check the voltage of C905(+)
Page 35
IBM L170 Service Manual 2.) W / LED , No Backlight Check C201(+) =12V Change F902 Check D201/Q209/Q210 or D202/Q211/Q212 Check ON/OFF signal Check Interface board Check U201 pin9=12V Change Q201 or Q202 Check the pin1 of U201 have sawtooth wave Change U201 Check D201(-),D202(-) have the output of square wave at short time.
IBM L170 Service Manual 8.2.3 KeyPad Board OSD is unstable or not working Connect KeyPad Board Is KeyPad Board connecting normally ? Replace Button Switch Is Button Switch normally ? Replace KeyPad Board Is KeyPad Board Normally ? Check Main Board...
IBM L170 Service Manual 9. White-Balance, Luminance adjustment Approximately 30 minutes should be allowed for warm up before proceeding white balance adjustment. Before started adjust white balance ,please setting the Chroma-7120 MEM. channel 1 to 6500 color, MEM. channel 2 to 7200 color, and MEM.
IBM L170 Service Manual 17 Switch the chroma-7120 to RGB-mode (with press “MODE” button ) 18 switch the MEM.channel to Channel 03 ( with up or down arrow on chroma 7120 ) 19 The lcd-indicator on chroma 7120 will show x = 296 ±10, y = 311 ±10, Y = 190 ±5 cd/m...
Page 47
IBM L170 Service Manual ZD106 93L 39149 MLL5232B BY FULL POWER 0 PCS ZD107 93L 39149 MLL5232B BY FULL POWER 0 PCS ZD108 93L 39149 MLL5232B BY FULL POWER 0 PCS ZD109 93L 39149 MLL5232B BY FULL POWER 0 PCS...