Related Manuals for Sanyo KA-IF01RGB
Summary of Contents for Sanyo KA-IF01RGB
- Page 1 Interface Board MODEL KA-IF01RGB COMPONENT / RGB / CV IN H/HV G/CV S-VIDEO AUDIO Cr/Pr Cb/Pb Owner's manual Installation and Operation 1AA6P1P4055-- (IDKDB) Printed in Japan...
- Page 2 Installing Instruction of Interface Board CAUTION IN INSTALLATION G Through installation work, handling with more than two people is recommended. G When holding (moving or lifting) the Plasma Monitor, hold the Monitor's body. Do not handle it by holding the attached accessory parts (the Speakers), otherwise damage could be result.
-
Page 3: Installation
Installation NOTE : When you are using the Plasma Display without Stand, you need to place the Plasma Display screen facing down on a flat surface place where maintained with soft materials (such as a blanket) for protecting the display screen. - Page 4 Operating Instruction of Plasma Monitor The features described in this manual are available only with the Interface Board. Any information not contained in this manual will be found in the owner's manual of your Plasma Monitor.
-
Page 5: Operation Of Remote Control
Operation of remote control Remote Control Unit can be used as either Wired or Wireless. MUTE BUTTON POWER ON-OFF BUTTON Used to mute sound. Used to turn Plasma Monitor on or off. PICTURE BUTTON BACK BUTTON Used to select image level. ON-OFF PICTURE Used to go back to the... - Page 6 Terminals This board has INPUT TERMINALS for connecting computers and video equipment. Refer to the figure on pages 7 ~ 9 and connect properly. S-VIDEO INPUT JACK Connect video outputs from video equipment. (Refer to P7.) G S-VIDEO (Mini DIN 4-type) COMPONENT / RGB / CV IN H/HV G/CV...
-
Page 7: Connecting To Video Equipment
Connecting to video equipment (VIDEO, S-VIDEO) Cables used for connection (Cables are not supplied with this board.) • VIDEO Cable • S-VIDEO Cable • Audio Cable (RCA x 2) NOTE: We recommend you to use a cable shorter than 3m. Video Source (example) Video Cassette Recorder Video Disk Player... - Page 8 Connecting to component video (Component-VIDEO) Cables used for connection (Cables are not supplied with this board.) • Video Cable (RCA x 3) or (BNC x 3) • Audio Cable (RCA x 2) NOTE: We recommend you to use a cable shorter than 3m. Component Video Source (example) DVD Player Component video output equipment...
-
Page 9: Connecting To Computer
Connecting to computer (PC, RGB) Cables used for connection (Cables and Adapter are not supplied with this board or monitor.) • VGA Cable (HDB 15 pin) • MAC Adapter (in the case of connecting Macintosh computer) • Video Cable (BNC x 5) •... -
Page 10: Selecting Input Source
Selecting input source Select mode "PC", "RGB", "Component-VIDEO", "S-VIDEO" or "VIDEO" by pressing INPUT button on Remote Control Unit or on Plasma Monitor's Front Control. (For connections, refer to pages 7 ~ 9.) ON-OFF PICTURE MUTE ➡ INPUT INPUT BACK button Component-VIDEO S-VIDEO... - Page 11 Picture image level select Select image level by pressing PICTURE button on the Remote Control Unit. ON-OFF PICTURE MUTE PICTURE button ➡ INPUT BACK In PC or RGB mode : Graphic Graphic Select this mode when watching graphic image. Standard Standard Normal picture level preset on this Plasma Monitor.
-
Page 12: Image Level Adjustment
Image level adjustment 1. Press MENU button and ON-SCREEN MENU will appear. 2. Press ed buttons to select "Picture setup" menu, and press OK button. "Picture setup" menu will appear. 3. Press ed buttons to select "Picture adjustment" menu, and press OK button. "Picture adjustment" menu will appear. - Page 13 Wide screen operations ➡ Select screen size among "Natural wide", "Zoom", "Zoom(Caption-IN)", "Full" and "Normal" by pressing WIDE button on Remote Control Unit. MENU LOCAT 2-Win SIZE STATUS WIDE ON-OFF WIDE button Natural wide Natural wide Provides image to fit width of screen by expanding both sides of image.
- Page 14 Wide image adjustment 1. Press MENU button and ON-SCREEN MENU will appear. 2. Press ed buttons to select "Picture setup" menu, and press OK button. "Picture setup" menu will appear. 3. Press ed buttons to select "Display position" menu, and press OK button. "Display position" menu will appear.
- Page 15 Cinema auto 1. Press MENU button and ON-SCREEN MENU will appear. 2. Press ed buttons to select "Picture setup" menu, and press OK button. "Picture setup" menu will appear. 3. Press ed buttons to select "Cinema auto" menu, and press OK button. "Cinema auto" menu will appear.
-
Page 16: Setting Menu
Setting menu 1. Press MENU button and ON-SCREEN MENU will appear. 2. Press ed buttons to select "System setup", and press OK button. "System setup" will appear. 3. Press ed buttons to select the item that you want to setup, and setup the selected item by press- ing 7 8 buttons. -
Page 17: Pip Operation
➡ PIP operation In PIP operation, use these buttons shown below : MENU LOCAT SIZE LOCAT 2-Win SIZE button button STATUS WIDE ON-OFF 2-WIN PIP ON-OFF button button Available input modes for each window are below : main window sub window S-VIDEO VIDEO S-VIDEO... - Page 18 PIP operation Selecting PIP screen location While PIP mode is on, press LOCAT button on Remote Control Unit to select PIP screen location. Lower left Upper right Lower right Upper left Selecting 2-window screen Press 2-WIN button on Remote Control Unit to show 2-window screen. main 2-win OFF 2-window (16 : 9)
- Page 19 Appendix RS232C TERMINAL Terminal : HDB9-PIN Connect the serial port of computer to this terminal with Serial Cross Cable (not supplied). Pin Configuration INTERFACE No Connect No Connect Protocol RS-232C R x D No Connect Baud rate 9600 bps T x D No Connect Data length 8 bits...