Pioneer DEH-P8400MP Installation Manual
Hide thumbs
Also See for DEH-P8400MP:
- Operation manual (124 pages) ,
- Service manual (89 pages) ,
- Catalog (52 pages)
Advertisement
Available languages
Available languages
DEH-P8400MP
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est con-
forme à CEMA.
Printed in Thailand
Imprimé en Thaïlande
<CRD3572-A/N> UC
<KSNZX/01K00001>
Connecting the Units
Note:
• This unit is for vehicles with a 12-volt battery and
• When this product's source is switched ON, a con-
negative grounding. Before installing it in a recre-
trol signal is output through the blue/white lead.
ational vehicle, truck, or bus, check the battery
Connect to an external power amp's system remote
voltage.
control or the car's Auto-antenna relay control ter-
• To avoid shorts in the electrical system, be sure to
minal (max. 300 mA 12 V DC). If the car features
disconnect the ≠ battery cable before beginning
a glass antenna, connect to the antenna booster
installation.
power supply terminal.
• Refer to the owner's manual for details on con-
• When an external power amp is being used with
necting the power amp and other units, then make
this system, be sure not to connect the blue/white
connections correctly.
lead to the amp's power terminal. Likewise, do not
• Secure the wiring with cable clamps or adhesive
connect the blue/white lead to the power terminal
tape. To protect the wiring, wrap adhesive tape
of the auto-antenna. Such connection could cause
around them where they lie against metal parts.
excessive current drain and malfunction.
• Route and secure all wiring so it cannot touch any
• To avoid short-circuiting, cover the disconnected
moving parts, such as the gear shift, handbrake
lead with insulating tape. Especially, insulate the
and seat rails. Do not route wiring in places that
unused speaker leads without fail. There is a possi-
get hot, such as near the heater outlet. If the insula-
bility of short-circuiting if the leads are not insulat-
tion of the wiring melts or gets torn, there is a dan-
ed.
ger of the wiring short-circuiting to the vehicle
• To prevent incorrect connection, the input side of
body.
the IP-BUS connector is blue, and the output side
• Don't pass the yellow lead through a hole into the
is black. Connect the connectors of the same colors
engine compartment to connect to the battery. This
correctly.
will damage the lead insulation and cause a very
• If this unit is installed in a vehicle that does not
dangerous short.
have an ACC (accessory) position on the ignition
• Do not shorten any leads. If you do, the protection
switch, the red lead of the unit should be connected
circuit may fail to work when it should.
to a terminal coupled with ignition switch ON/OFF
• Never feed power to other equipment by cutting
operations. If this is not done, the vehicle battery
the insulation of the power supply lead of the unit
may be drained when you are away from the vehi-
and tapping into the lead. The current capacity of
cle for several hours. (Fig. 1)
the lead will be exceeded, causing overheating.
• When replacing fuse, be sure to use only fuse of
the rating prescribed on this unit.
• Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded or
the left and right ≠ speaker leads are common.
• Speakers connected to this unit must be high-
power types with minimum rating of 50 W and
impedance of 4 to 8 ohms. Connecting speakers
ACC position
No ACC position
with output and/or impedance values other than
those noted here may result in the speakers catch-
ing fire, emitting smoke, or becoming damaged.
• The black lead is ground. Please ground this lead
separately from the ground of high-current prod-
ucts such as power amps.
If you ground the products together and the ground
becomes detached, there is a risk of damage to the
products or fire.
• Cords for this product and those for other products
may be different colors even if they have the same
function. When connecting this product to another
product, refer to the supplied Installation manuals
of both products and connect cords that have the
same function.
7 When not connecting a rear speaker lead to a Subwoofer
Antenna jack
15 cm
(5-7/8 in.)
15 cm
IP-BUS input (Blue)
(5-7/8 in.)
15 cm
(5-7/8 in.)
15 cm
(5-7/8 in.)
23 cm
(9 in.)
This Product
IP-BUS cable
Multi-CD player
(sold separately)
Yellow/black
If you use a cellular telephone, connect it via the
Audio Mute lead on the cellular telephone. If not,
keep the Audio Mute lead free of any connections.
Yellow
To terminal always supplied
Fuse holder
with power regardless of
ignition switch position.
Red
To electric terminal controlled by
Fuse resistor
ignition switch (12 V DC) ON/OFF.
Orange/white
To lighting switch terminal.
Fig. 1
Black (ground)
To vehicle (metal) body.
With a 2 speaker system, do not connect anything to
the speaker leads that are not connected to speakers.
Use this for connections when you have the separately
available amplifier.
Front output (FRONT OUTPUT)
Connecting cords
with RCA pin plugs
Rear output (REAR OUTPUT)
(sold separately)
Subwoofer output or Non Fading output
(SUBWOOFER or NON-FADING OUTPUT)
Blue/white
To system control terminal of the power amp
or Auto-antenna relay control terminal
(max. 300 mA 12 V DC).
System remote control
+
Front speaker
≠
White
Gray
+
Front speaker
≠
White/black
Gray/black
Left
Green
Violet
+
Rear speaker
≠
Green/black
Violet/black
+
Rear speaker
≠
+
Subwoofer
≠
<ENGLISH>
Power amp
(sold separately)
Power amp
(sold separately)
Power amp
(sold separately)
+
Front speaker
≠
+
Front speaker
≠
Right
+
Rear speaker
≠
+
Rear speaker
≠
+
Subwoofer
≠
Fig. 2
Advertisement
Table of Contents
Related Manuals for Pioneer DEH-P8400MP
Summary of Contents for Pioneer DEH-P8400MP
- Page 1 (SUBWOOFER or NON-FADING OUTPUT) • Route and secure all wiring so it cannot touch any • To avoid short-circuiting, cover the disconnected DEH-P8400MP This Product IP-BUS cable moving parts, such as the gear shift, handbrake lead with insulating tape.
-
Page 2: Connecting The Units
Connecting the Units <ENGLISH> Installation <ENGLISH> 7 When using a Subwoofer without using a different amp (sold separately) Note: Installation without the rubber bush (Fig. 6) • Before finally installing the unit, connect the • If installation angle exceeds 60° from horizontal, Dashboard wiring temporarily, making sure it is all connected the unit might not give its optimum performance. -
Page 3: Din Rear-Mount
Installation <ENGLISH> DIN Rear-mount About the fixing screws for the front panel If you do not operate the Detaching and Replacing the Front Panel Function, use the sup- plied fixing screws and fix the front panel to this unit. Installation using the screw holes on the side of the unit 1. -
Page 4: Raccordements Des Appareils
Raccordements des appareils <FRANÇAIS> 7 Lorsque l’on ne connecte pas de câble de liaison au haut-parleur d’extrêmes graves Remarque: • Cet appareil est destiné aux véhicules avec une bat- • Quand la source de ce produit est positionnée sur terie de 12 V, avec pôle négatif à la masse. Avant de ON, un signal de commande est sorti par le fil Amplificateur de l’installer dans un véhicule de loisir, un camion ou... -
Page 5: Montage Din Avant/Arrière
Raccordements des appareils <FRANÇAIS> Installation <FRANÇAIS> 7 Lors de l’utilisation d’un haut-parleur d’extrêmes graves sans amplificateur Remarque: Installation sans la bague en caoutchouc (Fig. 6) • Avant de finaliser l’installation de l’appareil, con- • L’angle de l’installation, ne doit pas dépasser 60° extérieur (vendu séparément) Tableau de bord necter temporairement le câblage en s’assurant que... -
Page 6: Montage Din Arrière
Installation <FRANÇAIS> Montage DIN arrière À propos des vis de fixation de la face avant Si vous n’utilisez pas la fonction de dépose et pose de la face avant, utilisez la vis de fixa- tion fournie et fixez la face avant à l’appareil. Installation en utilisant les trous de vis sur les côtés de l’appareil 1.