Advertisement
Quick Links
Download this manual
See also:
Programming Manual
Record a Message
Your system can record brief single or multiple messages. The total
available recording time is 184 seconds.
Press
Function
this
Perform the following...
Icon...
• Select "Add New" to Record a Message.
• Select "Record".
• Select "Stop" when recording is complete.
Record a
Then select "".
Message
• The recorded message list is displayed.
Message
Select the "" to return to the Security
Home Screen.
• Select the Message that you wish to play
Play OR
or delete.
Delete
• Select "Play" or "Delete All" as applicable.
Messages
• Select the "" to return to the Security
Message
Home Screen.
System Displays
A "beeping" at the control, indicates a trouble condition in the system and
requires your attention. Determine if the zone(s) displayed are intact and
make them so if they are not. If the display persists, CALL FOR SERVICE.
Press any key to silence the beeping for these conditions.
The following icons will be displayed on the Home screen along with zone
status information (if applicable) indicating system status:
Icon
Function
Icon
Function
Icon
AC Loss
Door Open
Alarm
Window
(intrusion)
Open
Armed
Exit Active
Away
Armed
Fire
OR
Stay
Heat
Sensor
Battery
Flood
Low
Check
Glass Break
Zones
CO Alarm
Medical
Alarm
Disarmed
Motion
Not Ready
to Arm
Disarmed
Temperature
Ready to
Arm
See the full User Guide for additional details.
Servicing Information
Your local Honeywell dealer is the person best qualified to service your
alarm system. Arranging some kind of regular service program with him
is advisable. Your local Honeywell dealer is:
Name:
Address:
Phone:
Ê800-16089oŠ
800-16089 12/13 Rev A
Part 1
Setting the Date and Time
NOTE: The system must be disarmed before date/time can be set. You
can set the time and date by doing the following:
•
Use the "" or "" to select the correct month/year.
•
Select the correct date. Use the "" to advance.
Select "Clear" then enter the correct time
•
Date Time
•
Select AM/PM then select "Save" or use the "" to advance
Select correct Time Zone
•
•
Enable/disable Day Light Savings Time.
•
If required select Day Light Saving Start/End Month/Week
Select "Save"
•
Manually Controlling Home Automation Devices
Your system may be equipped Home Automation (Z-Wave) Devices.
These devices are normally controlled using programmed scenes but can
also be activated/controlled manually. To control home automation
devices manually, perform the following:
Press these Keys or
Mode
Icons...
• You may be able to override
automatically controlled Z-
wave devices using the
OR
Automation commands.
68
• Some devices can be manually
activated or deactivated using
OR
the Automation commands.
Activating
• See your Installer for details
Z-Wave
on controlling Z-Wave devices.
+
Function
OR
Devices
Garage
Automation
For
Door Fault
regarding your system's Home
WiFi source
Automation features refer to the
present
full version User Guide and to
OR
the
No WiFi
(P/N 800-16091 or later).
source
94 Phone
Video Camera Control
Line Cut
Your system may be equipped to view and control video cameras. To
103 Comm.
view video and/or control the camera, perform the following:
Trouble
•
Select a camera from the displayed list.
90 RF Jam
•
Control the camera as applicable using the displayed
controls.
Video
For additional information regarding the video camera
Cover
control feature refer to the LYNX Touch L5200 User Guide
Tamper
(P/N/ 800-16083 or later).
Reporter
Failure
Connecting a Mobile Device (iOS)
Before attempting to connect your Mobile Device to the LYNX Touch
Automation
Control Panel, ensure that the LYNX Touch is connected to a WiFi Network
(Z-Wave
(router). Perform the steps below to connect up to four Mobile Devices to
Failure)
the LYNX Touch control.
Connect your Mobile Device to the WiFi Network
1. Ensure that you have connected
your
Mobile Device to the same WiFi
Network as your LYNX Touch Control Panel. For additional information
refer to the LYNX Touch User Guide P/N 800-10615V1 (or higher).
Connect your Mobile Device to the LYNX Touch
1. At the LYNX Touch Master User screen, select the "Keypad" icon.
2. At the Mobile Device, select the "L5100 Connect" icon.
3. A Honeywell License and User Agreement is displayed. After reading
the agreement, select "Agree". You must agree to the terms in order
to use the application.
4. "Discovering Control Panel..." is displayed.
5. Within 10-20 seconds the Device will display the Security Screen or
the Dashboard screen if Total Connect Services are enabled.
6. The control will display ID information for your Mobile Device.
7. Select the "" to return to the Master User Screen.
8. A Security Screen is displayed on your Mobile Device, which can now
be used to locally control your system.
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2013 Honeywell International Inc.
www.honeywell.com/security
LYNX TOUCH L5200 SERIES SECURITY SYSTEM
Full User Guide Available Online: This Quick Guide describes the most frequently used features and functions of your system. For full details of
all user functions, please see the system's User Guide located online at: http://www.security.honeywell.com/hsc/products (see LYNX Touch
L5200 Security System User Guide P/N 800-16083 or higher). The full version User Guide is also available from your installer upon request.
Congratulations on your ownership of a Honeywell Security System. This system provides:
• Three forms of detection: burglary, fire and emergency (see your installer for which forms of detection are installed)
• At least one keypad which provides control of system and displays system status
• Various sensors for perimeter and interior burglary detection
• Optional smoke or combustion detectors designed to provide early warning in case of fire.
What happens
Your system may also be programmed to automatically send alarm and status messages to a Central Monitoring Station.
System Basics
The following is a list of some of the most common features and
functions of your system:
• Several modes of burglary detection: Stay, Away, Instant.
• Bypass feature lets you bypass selected zones while leaving the
rest of the system armed.
• Chime mode alerts you to the opening of protected doors and
windows while the system is disarmed.
• Fire and carbon monoxide detection are always active (if
additional
information
installed) and an alarm sounds if a fire or carbon monoxide
condition is detected.
• Panic keys (if programmed) let you manually initiate fire, police
and medical alarms using the keypad.
Home
Automation
Guide
• 4-digit security codes are used in conjunction with keypad
commands to perform system functions.
• Each user (up to 32) can be assigned a different security code.
• The system sensing devices have been assigned to various
"zones," which are specific areas of detection (e.g., front door,
kitchen window, etc.).
• Zone numbers (points of detection) are displayed at the keypad
when an alarm or trouble condition occurs.
• Message Center allows recording and play-back of brief voice
messages.
• Speaker Phone allows the control to be used for hands free
telephone conversation. See the full User Guide for details.
• Two-way Voice allows the Central Station to listen, talk or
conduct a two-way conversation with in individuals at the
premises. See the full User Guide for details.
• Follow me reminder announcements allow the panel to dial a
number and deliver system status messages. See the full User
Guide for details.
• A Scheduling feature can be programmed to automatically
perform certain functions (e.g., arm the system) at a
predetermined time each day. See the full User Guide for details.
Entry/Exit Delays
• Entry Delays give you time to disarm the system when you
enter through the designated entrance door.
• You must disarm the system before the entry delay period ends,
or an alarm will occur (keypad beeps during the entry delay
period, reminding you to disarm the system).
• Exit delay gives you time after arming the system to leave
through the designated exit door(s) without setting off an alarm.
If programmed, a slow beeping will sound during the exit delay
period until the last 10 seconds, which then changes to fast
beeping (alerting you to the end of exit delay). If you cannot
leave within this delay time period, you should stop, disarm the
system, and start over to avoid a false alarm.
• See your installer for your delay times. See the full User Guide
for details on Exit Error alarms.
Quick Guide to User Functions
Notes on Burglary Detection
• The system must be armed before the burglary detection can
sense intrusions.
• To arm your system, select the desired arming key or icon and
enter your security code.
• To arm your system, if the Quick Arm feature is enabled select
the desired arming key or icon followed by the Quick Arm icon.
You do not need to enter your security code.
• To disarm the system, select the Disarm icon and enter your
security code.
• When an alarm occurs, the control sounds and displays the
zone(s) causing the alarm. An external sounder may also
sound, if installed.
• If your system is connected to a Central Monitoring Station, an
alarm message is also sent (delayed 30 seconds by default to
reduce false alarms).
• To stop the alarm sounding, simply disarm the system.
• Memory of Alarm: When an alarm condition occurs, the
keypad displays the number(s) of the zone(s) that caused the
problem, and displays the type of alarm. Clear the Memory of
Alarm display by entering another "off" sequence.
If you return to the premises and the burglary sounder is
on, or the keypad beeps rapidly upon entering the
premises, it indicates that an alarm has occurred during
your absence and an intruder may still be on the
premises. LEAVE IMMEDIATELY and CONTACT THE
POLICE from a nearby safe location.
Notes on Fire and CO Detection
• Your fire alarm system (if installed) is on 24 hours a day, for
continuous detection. In the event of an emergency, the
smoke and heat detectors sound their alarms, triggering a
loud, interrupted pulsed sound from the control and any
external sounder(s) (if installed).
• You can silence the alarm at any time by entering an Off
sequence.
• Carbon monoxide (CO) detectors, if installed, provide
continuous detection. If a high level of carbon monoxide is
detected, an interrupted pulsed alarm sound occurs at the
control and the detector(s). Immediately move to a spot
where fresh air is available, preferably outdoors. From a safe
area, call your security service provider for further
instructions. To silence the control sounding, enter an Off
sequence. To silence the detector, see its instructions.
IMPORTANT
LYNX Touch L5200
Advertisement
Related Manuals for Honeywell LYNX TOUCH L5200
Summary of Contents for Honeywell LYNX TOUCH L5200
- Page 1 Select “Save” • Message all user functions, please see the system’s User Guide located online at: http://www.security.honeywell.com/hsc/products (see LYNX Touch • The recorded message list is displayed. Message L5200 Security System User Guide P/N 800-16083 or higher). The full version User Guide is also available from your installer upon request.
- Page 2 Checking System or Zone Status/Bypassing Zones Panic Keys Testing the System Using the Test mode allows each detection point to be checked for proper operation. Testing Checking Zones: Before arming your system, all protected doors, windows and other detection Your system may have been programmed to use special keys/icons to manually activate should be conducted weekly to ensure proper operation.