Table of Contents
Advertisement
Quick Links
Quick reference guide
PROGRAM SELECTION
START/RESUME BUTTON
BUTTON
Push this button to start the selected program: the
Push "Programs" button
indicator lights up and goes off at the end of the program.
(repeatedly) until the indicator
When the door is opened during a washing cycle, the
of the required program lights
cycle is temporarily paused: the Start indicator blinks.
up (see "Table of programs"
To resume the cycle push Start button and close
below).
the door within 3 seconds.
Table of programs
P
Programs
1
AutoSensor 50-65°C
2
Pre-Wash
cold
3
Quickwash
45°C
4
2)
50°C
Eco
5
Intensive
70°C
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions
(without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible
with sensor programs as a result of the appliance's automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for
detailed information on the EN/Standard loading comparison test and other tests, contact the following address:
"nk_customer@whirlpool.com".
(see at right for options description)
CANCEL/OFF BUTTON
Push this button to switch off the control panel.
If pressed when a program is running it cancels the
program ongoing draining water for 1 minute
(0:01 is shown into the display).
If pressed when the dishwasher is switched off, it
drains any possible liquids from dishwasher
(1minute process).
Available
Loading instructions
options
Recommended program for
Delay
routine washes, with dried-on
Half load
food (e.g. EN 50242).
Delay
Crockery to be washed later.
Lightly soiled crockery, with no
Delay
dried-on food.
Delay
Normally soiled crockery.
Half load
Energy-saving program.
Recommended program for
Delay
heavily soiled crockery, especially
suitable for pans and saucepans.
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ
ANY BUTTON EXCEPT CANCEL/OFF BUTTON. FOR ENERGY SAVING
Options and display description
SALT INDICATOR
When lit (at the end of
the cycle), the salt
reservoir needs to be
refilled.
WASH TIME DISPLAY
Indicated the cycle duration and the remaining time (h:min). With "Delayed start" selected it indicates
the time remaining until program start (h.00) - below 1h (0:mim).
If "Fx Ey" messages appears on the display, see page 6 - chapter "What to do if...".
Consumption
Deter-
HALF LOAD BUTTON
gent
Half load cycle can be used for the
1)
Litres
kWh
Minutes
upper or lower rack. Select the
required program then press the
"Half Load" button - the light
comes on. Turns off at the end of
X
7-14 1.00-1.60
70-155
the program.
The "Half Load" option can be
used with the programs
indicated in the table of
programs.
—
4.0
0.03
14
X
11.0
0.80
30
TABLET SETTING
This setting allows to optimize the cycle performances
X
12.0
1.05
165
according the type of detergent used.
Push the Tablet button for 3 seconds (until the indicator lights
up) if you are using the combined detergents in tablet (rinse aid,
salt and detergent in 1 dose).
X
14.0
1.55
155
If you are using powder detergent or liquid detergent, the
Tablet indicator on the control panel has to be off.
ADG 9200
THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING
THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30
SECONDS IF NO CYCLE HAS STARTED.
RINSE AID
INDICATOR
When lit (at the end of
the cycle), the rinse aid
dispenser needs to be
refilled.
Chart
OPERATION
INDICATOR
A LED light projected
on the floor indicates
that the dishwasher is
working.
DELAYED START BUTTON
Push the button (repeatedly)
to delay the start of the
program. Adjustable from 1 to
24 hours. With each press of
the button, the delayed start
indicator increases by one
hour and after 24 restarts from
0. Then press the START
button. The dishwasher will
start after the set time.
5019 396 01936
GB -1-
Advertisement
Table of Contents
Related Manuals for Whirlpool ADG 9200
Summary of Contents for Whirlpool ADG 9200
- Page 1 2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: ADG 9200 5019 396 01936 “nk_customer@whirlpool.com”.
-
Page 2: First Time Use
First time use How to set water hardness in order to always assure the best cleaning results Water hardness should be set only - Press and hold together Programs and CANCEL/Off buttons for minimum 3 seconds. before the first wash or if water - The current water hardness setting will be visible on the display. -
Page 3: Daily Use
Daily check Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator Visual The rinse aid dosage can be indicator adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). -
Page 4: How To Load The Racks
How to load the racks How to load UPPER RACK How to adjust upper rack height (if available). (depending on the model) B - Cutlery basket - half: can be placed in the upper rack A - Adjustable flaps: in horizontal position for It could be useful to lift up the upper rack to have when the “Half load/Multizone”... -
Page 5: Maintenance And Care
Select program Overview of programs The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel (page 1). Choose program according to the attached table of programs (page 1). Duration of the program depends on the external conditions in the apartment, temperature and pressure etc. - Page 6 What to do if... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. How the faults are shown on the display: Function number “F”x - blinking Error number “E”y - blinking...
- Page 7 What to do if... Crockery and cutlery... Possible causes... Solutions..salt indicator lit - Use tablets for soft water. - Set “Tablet” option; if this option is not available, it is normal for the salt indicator to light up..have deposits: regeneration salt residue - Water too hard.
-
Page 8: Precautions And General Recommendations
What to do if... Disconnect the mains plug If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty). Before contacting our After-Sales Service, take note of the following: - the description of the fault, - the appliance type and model, - the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side:...