Page 1 This manual is for the EOS-1D X installed with firmware version ● INSTRUCTION 2.0.0 or later. MANUAL The “Software Start Guide” is included at the end of this manual. ●...
Page 2: Introduction
After shooting, play images back and check whether they have been properly recorded. If the camera or memory card is faulty and the images cannot be recorded or downloaded to a computer, Canon cannot be held liable for any loss or inconvenience caused.
Page 3: Item Check List
Item Check List Before starting, check that all the following items have been included with your camera. If anything is missing, contact your dealer. Eyecup Eg Battery Pack Battery Charger Camera LP-E4N LC-E4N (with body cap and (with protective cover) (with protective covers) battery compartment cap) Interface Cable...
Page 4: Conventions Used In This Manual
Conventions Used in this Manual Icons in this Manual <6> : Indicates the Main Dial. <5> : Indicates the Quick Control Dial. <9> : Indicates the Multi-controller. <0> : Indicates the Setting button. 0, 9, 7, 8 : Indicates that the corresponding function remains active for 4 sec., 6 sec., 10 sec., or 16 sec.
Page 5: Table Of Contents
Chapters Introduction Getting Started Setting the AF and Drive Modes Image Settings Exposure Control Flash Photography Shooting with the LCD Monitor (Live View Shooting) Shooting Movies Image Playback Post-Processing Images Sensor Cleaning Printing Images and Transferring Images to a Computer Customizing the Camera Reference Software Start Guide...
Page 6 Contents Introduction Item Check List................. 3 Conventions Used in this Manual............. 4 Chapters................... 5 Index to Features ................12 Handling Precautions ..............14 Quick Start Guide ................16 Nomenclature ................. 18 Getting Started Charging the Battery ..............30 Installing and Removing the Battery..........34 Installing and Removing the Card ..........
Page 7 Contents Setting the AF and Drive Modes 2: Selecting the AF Mode............66 S Selecting the AF Area............... 69 AF Area Selection Modes ............... 73 About the AF Sensor...............76 Lenses and Usable AF Points............77 Selecting AI Servo AF Characteristics (For a Subject) ....85 Customizing AF Functions ..............
Page 8 Contents Creating and Selecting a Folder........... 160 Changing the File Name............... 162 File Numbering Methods .............. 164 Setting Copyright Information............166 Setting the Color Space ............... 168 Exposure Control d: Program AE................170 s: Shutter-Priority AE ..............173 f: Aperture-Priority AE ............. 175 Depth of Field Preview...............
Page 9 Contents Using AF to Focus ................ 215 Focusing Manually ................ 222 Shooting Movies k Preparing to Shoot Movies ............. 226 k Shooting Movies ..............227 Autoexposure Shooting ..............227 Shutter-priority AE ..............228 Aperture-priority AE..............229 Manual Exposure Shooting ............231 Shooting Still Photos ..............236 Shooting Function Settings ............238 Setting the Movie-Recording Size..........239 Setting the Sound Recording ............242...
Page 10 Contents Viewing the Images on TV ............275 J Protecting Images..............279 K Recording and Playing Voice Memos ........281 a Copying Images ..............283 L Erasing Images................ 286 Changing Image Playback Settings ..........288 Adjusting the LCD Monitor Brightness........288 Auto Rotation of Vertical Images ..........
Page 11 Contents Custom Function Settings............. 326 C.Fn1: Exposure ................ 326 C.Fn2: Exposure ................ 330 C.Fn3: Drive ................333 C.Fn4: Disp./Operation ..............334 C.Fn5: Operation................ 336 C.Fn6: Others................339 85: Custom Controls ..............343 Registering My Menu ..............357 Saving and Loading Camera Settings ..........358 w: Registering Custom Shooting Modes ........361 Reference Function Availability Table According to Shooting Mode ....
Page 12: Index To Features
Index to Features Power AF point selection p.71 AI Servo AF characteristics p.85 Charging the battery p.30 Auto AF point selection: Battery check p.39 EOS iTR AF p.97 Battery information check p.372 AF Custom Functions p.94 Power outlet p.373 AF Microadjustment p.107 Auto power off p.57...
Page 13 Index to Features Shooting Image browsing (Jump display) p.258 Magnified view p.259 Shooting mode p.24 Image rotate p.261 Multiple exposures p.186 Rating p.262 Mirror lockup p.193 Movie playback p.268 Depth-of-field preview p.176 Slide show p.272 Remote Switch p.185 Viewing images on TV p.275 Quick Control p.51...
Page 14: Handling Precautions
The camera is not waterproof and cannot be used underwater. If you accidentally drop the camera into water, promptly consult your nearest Canon Service Center. Wipe off any water droplets with a dry cloth. If the camera has been exposed to salty air, wipe it with a well-wrung wet cloth.
Page 15 Handling Precautions LCD Panel and LCD Monitor Although the LCD monitor is manufactured with very high precision technology with over 99.99% effective pixels, there may be a few dead pixels among the remaining 0.01% or less pixels. Dead pixels displaying only black or red, etc., are not a malfunction.
Page 16: Quick Start Guide
Quick Start Guide Insert the battery (p.34) To charge the battery, see page 30. Insert a card (p.35) Two cards can be inserted. Attach the lens (p.43) Align it with the red dot. Set the lens focus mode switch to <f> (p.43) Set the power switch to <1>...
Page 17 Quick Start Guide Set the shooting mode to <d> (p.170) Press the <W> button. Look at the top LCD panel and turn the <6/5> dial to select <d>. Focus the subject (p.46) Look through the viewfinder and aim the viewfinder center over the subject.
Page 18: Nomenclature
Nomenclature Lens mount index (p.43) Mirror (p.193, 303) Depth-of-field preview button (p.176) Movie microphone (p.242) Multi-function button 2 (p.345) Self-timer lamp (p.117) Lens lock pin Shutter button (p.46) Lens release button (p.44) Lens mount Grip Vertical-grip on/off switch (p.49) Tripod socket ...
Page 19 Nomenclature White balance selection <O> Exposure compensation/ button (p.143) Aperture button (p.181/177) AF area selection LCD panel illumination mode/Multi-function/ button (p.50) Multi-spot metering button (p.70/196/180) Hot shoe ISO speed Flash-sync contacts setting button (p.130) <6> Main Dial Eyecup (p.47) (p.45)
Page 20 Nomenclature <V> Focal plane mark Top LCD panel (p.24, 25) <Q> Metering mode <A> Live View shooting/ selection/Flash exposure Movie shooting button compensation button (p.206/226) (p.179/196) <W> Shooting AF start button mode selection button (p.46, 67, 68, 208, 234) (p.170, 207, 227, 228) <A>...
Page 21 Nomenclature 　　 <M> Menu Info button button (p.53) (p.209, 233, 252, 254, 370) Card slot 1 Strap mount (p.35) (p.29) Card slot 2 (p.35) Card slot cover (p.35) Terminal cover Card 1 eject button (p.37) Card 2 eject button (p.37) <Y>...
Page 22: Viewfinder Information
Nomenclature Viewfinder Information Spot metering circle (p.179) Area AF frame (p.70) Focusing screen (p.334) <S> Single AF point <O> Spot AF (single point) (p.73) Grid (p.61) Exposure level indicator Max. burst (p.128) Remaining number of exposures (p.188) JPEG icon (p.127) ...
Page 23 Nomenclature <g> ISO speed (p.130) <q> Metering mode (p.179) <o> Focus confirmation light (p.170) Shooting mode <e> AF status indicator (p.106) <A> AE lock (p.183) ISO speed (p.130) AEB in-progress (p.182) Multi-spot metering (p.180) <A> Highlight tone priority (p.156) <D> Flash-ready (p.196) Possible shots Improper FE lock warning Card full warning (Full)
Page 24: Shooting Mode P
Nomenclature Top LCD Panel Shutter speed Aperture Bulb (buLb) AEB amount Bulb exposure time (min.:sec.) Dust Delete Data acquisition ( FE lock (FEL) Busy (buSY) AF point selection Multi function lock warning (L) AF, SEL [ ], SEL AF) No card warning (Card) AF point registration Error code (Err) HP, SEL [ ], SEL HP)
Page 25 Nomenclature <N> Auto Lighting Optimizer (p.152) White balance correction (p.150) Metering mode (p.179) q Evaluative metering <0> Monochrome shooting w Partial metering (p.136) r Spot metering e Center-weighted average metering White balance (p.143) Q Auto Drive mode (p.115) Daylight Single shooting E Shade o High-speed...
Page 26 Nomenclature Rear LCD panel <g> Card 2 indicator <r> GPS device connection* (p.36) Movie-recording size (p.239) L : Full High-Definition recording quality <J> Card 2 selection K : High-Definition recording icon (p.36) quality J : Standard-definition recording quality <f> Card 1 indicator (p.36) <s>...
Page 27 Nomenclature Battery Pack LP-E4N Lock lever Contacts Battery release handle Protective cover...
Page 28 Nomenclature Battery Charger LC-E4N Charger for Battery Pack LP-E4N (p.30). Charge level/Calibration (Discharge) status indicator/ Performance check lamp Charge lamp Calibration/Performance Battery pack slot check button Car battery cable socket Power cord socket Protective covers (2) Power cord The charger can also recharge the Battery Pack LP-E4.
Page 29: Getting Started
Getting Started This chapter explains preparatory steps before you start shooting and basic camera operations. Attaching the Strap Pass the end of the strap through the camera’s strap mount eyelet from the bottom. Then pass it through the strap’s buckle as shown in the illustration.
Page 30: Charging The Battery
Charging the Battery Connect the charger to a power outlet. Connect the power plug to a power outlet, and connect the power cord to the charger. When no battery is attached, all the indicator lamps will be off. Remove the protective covers. As shown in the illustration, detach the charger’s protective cover (provided) and the battery’s protective...
Page 31 Charging the Battery Tips for Using the Battery and Charger Upon purchase, the battery is not fully charged. Recharge the battery before using. Recharge the battery on the day before or on the day it is to be used. Even during storage, a charged battery will gradually drain and lose its capacity. After recharging the battery, detach it and disconnect the charger from the power outlet.
Page 32 Charging the Battery Use a Car’s Cigarette Lighter Socket to Recharge the Battery With Car Battery Cable CB-570 (sold separately), you can connect the charger’s car battery cable socket (<DC IN> terminal) to your car’s cigarette lighter socket. When recharging the battery this way, be sure that the car’s engine is running.
Page 33 All Three Charge Level Indicators Blink If any of the following occurs, remove the battery from the charger and consult your dealer or nearest Canon Service Center: All the Charge level lamps blink in green, all the Calibration (Discharge) status indicator lamps blink in red, or the indicators blink alternately in red and green (including the <CAL/CHARGE>...
Page 34: Installing And Removing The Battery
Installing and Removing the Battery Load a fully charged Battery Pack LP-E4N/LP-E4 into the camera. The camera’s viewfinder becomes bright when a battery is installed, and darkens when the battery is removed. Installing the Battery Remove the battery compartment cap. Insert the battery.
Page 35: Installing And Removing The Card
Installing and Removing the Card You can insert up to two cards. Images can be recorded when at least one card is installed in either slot in the camera. If you insert two cards, you can select which card to record images to or record images simultaneously on both cards (p.120, 122).
Page 36 Installing and Removing the Card Set the power switch to <1> Possible shots (p.38). The number of possible shots will be displayed on the top LCD panel and in the viewfinder. The rear LCD panel will indicate which card(s) has been inserted. The images will be recorded to the Card selection icon card with the <...
Page 37: Removing The Card
Installing and Removing the Card Removing the Card Open the cover. Set the power switch to <2>. Make sure the access lamp is off, then open the cover. If [Recording...] is displayed, close the cover. Access lamp Remove the card. Push the eject button to eject the card.
Page 38: Turning On The Power
Turning on the Power If you turn on the power switch and the Date/Time/Zone setting screen appears, see page 40 to set the Date/Time/Zone. <1> : The camera turns on. <R>: The camera turns on. The Multi-function lock will take effect (p.50).
Page 39: Checking The Battery Level
Turning on the Power z Checking the Battery Level When the power switch is set to <1>, the battery level will be indicated in one of six levels. Icon Level (%) Indication 100 - 70 Sufficient battery level 69 - 50 Battery level exceeds 50% 49 - 20 Battery level below 50% 19 - 10 Battery level is low 9 - 1...
Page 40: Setting The Date, Time, And Zone
Setting the Date, Time, and Zone When you turn on the power for the first time or if the date/time has been reset, the Date/Time/Zone setting screen will appear. Follow steps 3 to 6 to set the current date, time, and time zone. Note that the date/time appended to recorded images will be based on this date/time setting.
Page 41: Set The Date And Time
3 Setting the Date, Time, and Zone Set the date and time. Turn the <5> dial to select the number. Press <0> so <r> is displayed. Turn the <5> dial to select the desired setting, then press <0> (Returns to <s>). Set the daylight saving time.
Page 42: Selecting The Interface Language
Selecting the Interface Language Display the menu screen. Press the <M> button to display the menu screen. Under the [52] tab, select [LanguageK]. Press the <Q> button and select the [5] tab. Turn the <6> dial to select the [52] tab.
Page 43: Attaching And Detaching A Lens
Attaching and Detaching a Lens The camera is compatible with all Canon EF lenses. The camera cannot be used with EF-S or EF-M lenses. Remove the caps. Remove the rear lens cap and the body cap by turning them as shown by the arrows.
Page 44: Detaching The Lens
Attaching and Detaching a Lens Minimizing Dust When changing lenses, do it quickly in a place with minimal dust. When storing the camera without a lens attached, be sure to attach the body cap to the camera. Remove dust on the body cap before attaching it. Detaching the Lens While pressing the lens release button, turn the lens as shown by...
Page 45: Basic Operation
Basic Operation Adjusting the Viewfinder Clarity Remove the eyecup. While grasping both sides of the eyecup, slide it upward to remove. Make the adjustment. Turn the knob left or right so that the AF points in the viewfinder look sharp. Attach the eyecup.
Page 46: Shutter Button
Basic Operation Shutter Button The shutter button has two steps. You can press the shutter button halfway. Then you can further press the shutter button completely. Pressing halfway This activates autofocusing and the automatic exposure system that sets the shutter speed and aperture. The exposure setting (shutter speed and aperture) is displayed in the viewfinder and on the top LCD panel (9).
Page 47 Basic Operation Main Dial After pressing a button, turn the <6> dial. When you press a button such as <W>, <o>, <Q>, or , the respective function remains selected for 6 seconds (9). During this time, you can turn the <6> dial to set the desired setting.
Page 48 Basic Operation 5 Quick Control Dial After pressing a button, turn the <5> dial. When you press a button such as <W>, <o>, <Q>, or , the respective function remains selected for 6 seconds (9). During this time, you can turn the <5> dial to set the desired setting.
Page 49 Basic Operation After pressing the <Q> button, tap the <5> dial’s inner ring at the top, bottom, left, or right. 9 Multi-controller The <9> consists of an eight-direction key and a button at the center. Use it to select the AF point, correct the white balance, move the AF point or magnifying frame during Live View shooting, scroll around magnified...
Page 50: Lcd Panel Illumination
Basic Operation R: Multi function lock With [85: Multi function lock] set (p.337) and the power switch set to <R>, you can prevent the current settings from changing due to accidental movement of the Main Dial, Quick Control Dial, or Multi-controller. If the power switch is set to <R>...
Page 51: Q Quick Control For Shooting Functions
Q Quick Control for Shooting Functions You can directly select and set the shooting functions displayed on the LCD monitor. This is called the Quick Control screen. Press the <Q> button. The Quick Control screen will appear (7). Set the desired function. Use <9>...
Page 52 Q Quick Control for Shooting Functions Settable Functions on Quick Control Screen AE lock* (p.183) Highlight tone priority* (p.156) White balance (p.143) Exposure compensation/ Aperture (p.175) AEB setting (p.178, 181, 182) Shutter speed (p.173) ISO speed (p.130) Shooting mode* (p.24) Auto Lighting Optimizer Flash exposure (p.152)
Page 53: Menu Operations
Menu Operations You can set various settings with the menus such as the beeper, date/ time, etc. While looking at the LCD monitor, use the <M> and <Q> buttons on the back of the camera and the <6> < > dials. <M>...
Page 54 3 Menu Operations Menu Setting Procedure Display the menu screen. Press the <M> button to display the menu screen. Select a tab. Each time you press the <Q> button, the main tab will switch. Turn the <6> dial to select a secondary tab.
Page 55: Before You Start
Before You Start 3 Formatting the Card If the card is new or was previously formatted by another camera or computer, format the card with the camera. When the card is formatted, all images and data in the card will be erased.
Page 56 Before You Start Format the card in the following cases: The card is new. The card was formatted by a different camera or a computer. The card is full with images or data. A card-related error is displayed (p.401). Cards with 128 GB or lower capacity will be formatted in FAT format. Cards with a capacity over 128 GB will be formatted in exFAT format.
Page 57: Setting The Power-Off Time/Auto Power Off
Before You Start 3 Setting the Power-off Time/Auto Power Off To save battery power, the camera turns off automatically after a set time of idle operation elapses. If you do not want the camera to turn off automatically, set this to [Disable]. After the power turns off, you can turn on the camera again by pressing the shutter button or other buttons.
Page 58: Reverting The Camera To The Default Settings
Before You Start 3 Reverting the Camera to the Default Settings The camera’s shooting settings and menu settings can be reverted to their defaults. Select [Clear all camera settings]. Under the [54] tab, select [Clear all camera settings], then press <0>. Select [OK].
Page 59 Before You Start Image-recording Settings AF Settings 3 (Large) Image type/size Case1/Parameter settings of all JPEG quality Case 1 - 6 cases cleared Picture Style Standard Auto Lighting Optimizer Standard AI Servo 1st image Equal priority priority Peripheral illumination Enable/Correction correction data retained AI Servo 2nd image priority Equal priority (0)
Page 60: Camera Settings
Before You Start Camera Settings Live View Shooting Settings LV z/k setting Auto power off 1 min. Stills Beep Enable AF mode Live mode Grid display Release shutter Enable without card Exposure simulation Enable Image review 2 sec. Silent LV shooting Mode 1 Highlight alert Disable...
Page 61: Displaying The Grid And Electronic Level
Displaying the Grid and Electronic Level You can display a grid and electronic level in the viewfinder and on the LCD monitor to help correct camera tilt. Displaying the Grid in the Viewfinder Select [VF grid display]. Under the [52] tab, select [VF grid display], then press <0>.
Page 62 Displaying the Grid and Electronic Level Displaying the Electronic Level on the LCD Monitor Press the button. Each time you press the button, the screen display will change. Display the electronic level. If the electronic level does not appear, set [52: z button display options] so that the electronic level can be displayed...
Page 63: Feature Guide
Feature Guide When [zHelp] is displayed at the bottom of the menu screen, the Feature guide, offering explanations of menu options, can be displayed. The Feature guide is displayed while you hold down the button. If it fills two or more screens, a scroll bar will appear on the right edge. To scroll, hold down the ...
Page 64 MEMO...
Page 65: Setting The Af And Drive Modes
Setting the AF and Drive Modes The 61 AF points in the viewfinder make AF shooting suitable for a wide variety of subjects and scenes. You can also select the AF mode and drive mode that best match the shooting conditions and subject. <AF>...
Page 66: 2: Selecting The Af Mode
2: Selecting the AF Mode You can select the AF mode to suit the shooting conditions or subject. On the lens, set the focus mode switch to <AF>. Press the <o> button. Select the AF mode. While looking at the top LCD panel, turn the <6>...
Page 67 2: Selecting the AF Mode One-Shot AF for Still Subjects Suited for still subjects. When you press the shutter button halfway, the camera will focus only once. When focus is achieved, the AF point that achieved focus will be displayed, and the focus confirmation light <o>...
Page 68: Ai Servo Af For Moving Subjects
2: Selecting the AF Mode AI Servo AF for Moving Subjects This AF mode is suited for moving subjects when the focusing distance keeps changing. While you hold down the shutter button halfway, the subject will be focused continuously. The exposure is set at the moment the picture is taken.
Page 69: S Selecting The Af Area
S Selecting the AF Area 61 AF points are provided for AF. You can select the AF point(s) suiting the scene or subject. Depending on the lens attached to the camera, the number of usable AF points and AF point patterns will differ. For details, see “Lenses and Usable AF Points”...
Page 70 S Selecting the AF Area AF point expansion (Manual selection, surrounding points) The manually-selected AF point <S> and the surrounding AF points <w> are used to focus. Zone AF (Manual selection of zone) The 61 AF points are divided into nine zones for focusing.
Page 71 S Selecting the AF Area Selecting the AF Point Manually You can manually select the AF point or zone. When 61-point automatic selection AF and AI servo AF are set, you can set the starting AF point for AI Servo AF. Press the <S>...
Page 72 S Selecting the AF Area AF Point Display Indications Pressing the <S> button lights up the AF points that are cross-type AF points for high-precision autofocusing. The blinking AF points are horizontal-line sensitive. For details, see page 76. AI Servo AF starting position When the AF area selection mode is set to 61-point automatic selection AF, you can manually select the AF point with which AI Servo AF is started (p.103).
Page 73: Af Area Selection Modes
AF Area Selection Modes Single-point Spot AF (Manual selection) Although this is the same as Single-point AF (manual selection), the selected AF point <O> covers a smaller area to focus. Effective for pinpoint focusing of overlapping subjects such as an animal in a cage. Since Single-point Spot AF (manual selection) covers a very small area, focusing may be difficult during hand-held shooting or for a moving subject.
Page 74 AF Area Selection Modes AF point expansion (Manual selection, surrounding points) The manually-selected AF point <S> and adjacent AF points <w> are used to focus. The AF point expansion is larger than with AF point expansion (manual selection ), so the focusing is executed over a wider area.
Page 75 AF Area Selection Modes 61-point automatic selection AF All the AF points are used to focus. With One-Shot AF, pressing the shutter button halfway will display the AF point(s) <S> that achieved focus. If multiple AF points are displayed, it means they all have achieved focus. This mode tends to focus the nearest subject.
Page 76: About The Af Sensor
About the AF Sensor The camera’s AF sensor has 61 AF points. The illustration below shows the AF sensor pattern corresponding to each AF point. With f/2.8 or larger maximum aperture lenses, high-precision AF is possible at the viewfinder center. Depending on the lens attached to the camera, the number of usable AF points and AF pattern will differ.
Page 77: Lenses And Usable Af Points
AF points will stay lit.) “Extender EF1.4x” and “Extender EF2x” apply to all the I/II/III models. Regarding new lenses marketed after the EOS-1D X, check Canon’s Web site to see which group they belong to. Some lenses may not be available in certain countries or regions.
Page 78 Lenses and Usable AF Points EF400mm f/2.8L USM EF16-35mm f/2.8L USM EF70-200mm f/2.8L USM EF400mm f/2.8L II USM EF16-35mm f/2.8L II USM EF70-200mm f/2.8L IS USM EF400mm f/2.8L IS USM EF17-35mm f/2.8L USM EF70-200mm f/2.8L IS II USM EF400mm f/2.8L IS II USM EF20-35mm f/2.8L EF80-200mm f/2.8L TS-E45mm f/2.8*...
Page 79 Lenses and Usable AF Points EF50mm f/2.5 Compact Macro TS-E24mm f/3.5L II* EF8-15mm f/4L Fisheye USM EF200mm f/2.8L USM EF100mm f/2.8 Macro EF17-40mm f/4L USM + Extender EF1.4x EF200mm f/2.8L II USM EF100mm f/2.8L Macro IS USM EF24-70mm f/4L IS USM + Extender EF1.4x EF300mm f/2.8L USM EF300mm f/4L USM...
Page 80 Lenses and Usable AF Points Group E Autofocusing with 61 points is possible. All of the AF area selection modes are selectable. : Cross-type AF point. Subject tracking is superior and high- precision focusing is achieved. : AF points sensitive to horizontal lines.
Page 81 Lenses and Usable AF Points EF70-200mm f/2.8L USM EF70-300mm f/4.5-5.6 DO IS USM EF80-200mm f/4.5-5.6 + Extender EF2x EF70-200mm f/2.8L IS USM EF75-300mm f/4-5.6 EF90-300mm f/4.5-5.6 + Extender EF2x EF70-200mm f/2.8L IS II USM EF75-300mm f/4-5.6 USM EF90-300mm f/4.5-5.6 USM + Extender EF2x EF70-200mm f/4L USM EF75-300mm f/4-5.6 II...
Page 82 Lenses and Usable AF Points Group G Only 33 of the 61 AF points can be used for autofocusing. All of the AF area selection modes are selectable. During automatic AF point selection, the outer frame marking the AF area (Area AF frame) will be different from 61-point automatic selection AF.
Page 83 Lenses and Usable AF Points AF when the maximum aperture is f/8 When an extender is attached to the lens, AF is possible even when the maximum aperture value is larger than f/5.6 up to f/8. Selectable AF area selection modes are the same as that of group H (p.82). EF400mm f/5.6L USM EF400mm f/4 DO IS USM EF70-200mm f/4L USM...
Page 84 Lenses and Usable AF Points Group I Autofocusing with 61 points is possible. All of the AF area selection modes are selectable. : Cross-type AF point. Subject tracking is superior and high- precision focusing is achieved. : AF points sensitive to horizontal lines.
Page 85: Selecting Ai Servo Af Characteristics (For A Subject)
Selecting AI Servo AF Characteristics (For a Subject) You can easily fine-tune AI Servo AF to suit a particular subject or scene just by selecting a case from 1 to 6. This feature is called the “AF Configuration Tool”. Select the [21] tab. Select a case.
Page 86 3 Selecting AI Servo AF Characteristics (For a Subject) Case 1: Versatile multi purpose setting Standard setting suited for any moving subject. Works with many subjects and scenes. Select [Case 2] to [Case 6] in the following cases: when obstacles enter AF points, when the subject tends to stray from AF points, when you want to Default settings...
Page 87 3 Selecting AI Servo AF Characteristics (For a Subject) Case 3: Instantly focus on subjects suddenly entering AF points Once an AF point starts tracking the subject, this setting enables the camera to focus consecutive subjects at different distances. If a new subject appears in front of the target subject, the camera will start focusing the new subject.
Page 88 3 Selecting AI Servo AF Characteristics (For a Subject) Case 5: For erratic subjects moving quickly in any direction Even if the target subject moves dramatically up, down, left, or right, the AF point will switch automatically to focus-track the subject. Effective for shooting subjects that move dramatically up, down, left, or right.
Page 89 3 Selecting AI Servo AF Characteristics (For a Subject) Case 6: For subjects that change speed and move erratically Geared for tracking moving subjects whose speed can change dramatically and suddenly. Also, if the target subject moves dramatically up, down, left or right and it is difficult to focus, the AF point switches automatically to track the subject.
Page 90 3 Selecting AI Servo AF Characteristics (For a Subject) About the Parameters Tracking sensitivity Sets the subject-tracking sensitivity during AI Servo AF when an obstacle enters the AF points or when the AF points stray from the subject. Standard setting suited for most moving subjects. [Locked on: -2 / Locked on: -1] The camera will try to continue focusing the subject even if an obstacle enters the AF points or if the subject strays from the AF...
Page 91 3 Selecting AI Servo AF Characteristics (For a Subject) Acceleration/deceleration tracking This sets the tracking sensitivity for moving subjects whose speed can suddenly change dramatically by starting or stopping suddenly, etc. Suited for subjects that move at a steady speed (minimal change in moving speed).
Page 92 3 Selecting AI Servo AF Characteristics (For a Subject) AF point auto switching This sets the switching sensitivity of the AF points as they track a subject that moves dramatically up, down, left, or right. This setting takes effect in the following AF area selection modes: AF point expansion (manual selection ), AF...
Page 93 3 Selecting AI Servo AF Characteristics (For a Subject) Changing Cases’ Parameter Settings You can adjust each case’s three parameters (1. Tracking sensitivity, 2. Accel./decel. tracking, and 3. AF pt auto switching) as desired. Select a case. Turn the <5> dial to select the icon of the case you want to adjust.
Page 94: Customizing Af Functions
Customizing AF Functions With the [22] to [25] menu tabs, you can set AF functions to suit your shooting style or subject. 22: AI Servo AI Servo 1st image priority You can set the AF operation characteristics and shutter-release timing for the first shot during continuous shooting with AI Servo AF.
Page 95 3 Customizing AF Functions -2/-1: Shooting speed priority Priority is given to the continuous shooting speed instead of achieving focus. With -2, decrease of continuous shooting speed can be better prevented than with -1. +1/+2: Focus priority Priority is given to achieving focus instead of the continuous shooting speed.
Page 96 3 Customizing AF Functions AF-assist beam firing Enables or disables the EOS-dedicated Speedlite’s AF-assist beam. ON: Enable The external Speedlite emits the AF- assist beam when necessary. OFF: Disable The external Speedlite will not emit the AF-assist beam. This prevents the AF- assist beam from disturbing others.
Page 97 3 Customizing AF Functions Auto AF point selection: EOS iTR AF When the AF area selection mode is set to 61-point automatic selection AF or Zone AF, AF is possible while using the subject’s color or face detection information. Using this function makes it easier to continue focusing a moving subject with AI Servo AF.
Page 98 3 Customizing AF Functions Lens drive when AF impossible If focus cannot be achieved with autofocus, you can have the camera keep searching for the correct focus or have it stop searching. ON: Continue focus search If focus cannot be achieved with autofocus, the lens is driven to search for the correct focus.
Page 99 3 Customizing AF Functions Selectable AF point You can change the number of manually selectable AF points. With automatic AF point selection, all 61 AF points will remain active regardless of this setting. : 61 points All 61 AF points will be manually selectable.
Page 100 3 Customizing AF Functions Select AF area selection mode You can limit the selectable AF area selection modes to suit your shooting preferences. Turn the <5> dial to select a selection mode, then press <0> to append a checkmark <X>. Then select [OK] to register the setting.
Page 101: Main Dial
3 Customizing AF Functions AF area selection method You can set the method for changing the AF area selection mode. → M-Fn button After you press the <S> button, the AF area selection mode changes each time you press the button. →...
Page 102 3 Customizing AF Functions : Separate AF pts: Area+pt The AF area selection mode and manually-selected AF point (or Zone) can be set separately for each camera orientation (1. Horizontal, 2. Vertical with the camera grip at the top, 3. Vertical with the camera grip at the bottom).
Page 103 3 Customizing AF Functions Initial AF point, AI Servo AF You can set the AI Servo AF’s starting AF point for when the AF area selection mode is set to Auto selection: 61 pt AF. : Initial AF pt selected AI Servo AF will start with the manually- selected AF point when the AF mode is set to AI Servo AF and the AF area...
Page 104 3 Customizing AF Functions Manual AF point selection pattern During manual AF point selection, the selection can either stop at the outer edge of the area AF frame or it can move to the opposite AF point. This function works in AF area selection modes other than 61-point automatic selection AF and Zone AF.
Page 105 3 Customizing AF Functions VF display illumination The AF points and grid in the viewfinder can be illuminated in red when focus is achieved. AUTO: Auto The AF points and grid are automatically illuminated in red under low light. ON: Enable The AF points and grid are illuminated in red regardless of the ambient light level.
Page 106 3 Customizing AF Functions AF status in viewfinder The AF status indicator indicating that AF is operating can be displayed in the viewfinder’s field of view or outside the field of view. : Show in field of view The AF status icon is displayed in the lower right of the viewfinder’s field of view.
Page 107: Fine Adjustment Of Af's Point Of Focus (Af Microadjustment)
Fine Adjustment of AF’s Point of Focus Fine adjustment of the AF’s point of focus is possible for viewfinder shooting and in Live View shooting’s [Quick mode]. This is called “AF Microadjustment”. Before making the adjustment, read “Notes for AF Microadjustment”...
Page 108 3 Fine Adjustment of AF’s Point of Focus Make the adjustment. Turn the <5> dial to make the adjustment. The adjustable range is ±20 steps. Setting it toward “–: ” will shift the point of focus in front of the standard point of focus.
Page 109 3 Fine Adjustment of AF’s Point of Focus Adjust by Lens You can perform AF Microadjustment for each lens and register the adjustment in the camera. You can register the adjustment for up to 40 lenses. When you autofocus with a lens whose adjustment has been registered, the point of focus will always be shifted by the adjustment amount.
Page 110 3 Fine Adjustment of AF’s Point of Focus Enter the serial number. Turn the <5> dial to select the digit, then press <0> to display <r>. Turn the <5> dial to enter the number, then press <0>. After entering all the digits, turn the <5>...
Page 111 3 Fine Adjustment of AF’s Point of Focus Make the adjustment. Single focal length lens For a zoom lens, turn the <5> dial and select the wide-angle (W) or telephoto (T) end. Press <0> to turn off the purple frame and make the adjustment. Turn the <5>...
Page 112 3 Fine Adjustment of AF’s Point of Focus Clearing All AF Microadjustment data When [ Clear all] appears at the bottom of the screen, pressing the <L> button will clear all the adjustment data set for [All by same amount] and [Adjust by lens]. Notes for AF Microadjustment The AF’s point of focus will vary slightly depending on the subject conditions, brightness, zoom position, and other shooting conditions.
Page 113: When Autofocus Fails
When Autofocus Fails Autofocus can fail to achieve focus (the viewfinder’s focus confirmation light <o> blinks) with certain subjects such as the following: Subjects difficult to focus Very low-contrast subjects (Example: Blue sky, solid-color walls, etc.) Subjects in very low light Extremely backlit or reflective subjects (Example: Car with a highly reflective body, etc.) Near and far subjects covered by an AF point...
Page 114: Mf: Manual Focusing
When Autofocus Fails MF: Manual Focusing Set the lens focus mode switch to <MF>. Focus the subject. Focus by turning the lens focusing ring until the subject looks sharp in the viewfinder. Focusing ring If you press the shutter button halfway while focusing manually, the focus confirmation light <o>...
Page 115: R: Selecting The Drive Mode
R: Selecting the Drive Mode Single and continuous shooting drive modes are provided. Press the <o> button. Select the drive mode. While looking at the top LCD panel, turn the <5> dial. u : Single shooting When you press the shutter button completely, only one shot will be taken.
Page 116 R: Selecting the Drive Mode : Single: Silent shooting The shooting sound for single shooting is quieter than . The internal mechanical operation is not executed until you return the shutter button to its halfway position. K: Super high speed continuous shooting (Max.
Page 117: Using The Self-Timer
j Using the Self-timer Use the self-timer when you want to be in the picture. Press the <o> button. Select the self-timer. While looking at the top LCD panel, turn the <5> dial to select the self- timer. k : 10-sec. self-timer l : 2-sec.
Page 118 MEMO...
Page 119: Image Settings
Image Settings This chapter explains image-related function settings: Image-recording quality, ISO speed, Picture Style, white balance, Auto Lighting Optimizer, lens peripheral illumination correction, chromatic aberration correction, and other functions.
Page 120: Selecting The Card For Recording And Playback
Selecting the Card for Recording and Playback If a card is inserted in either Card f or Card g, you can start shooting. When only one card is inserted, the procedures described on pages 120 to 122 are not necessary. If you insert two cards, you can select the recording method and select which card to use to record and play back images.
Page 121 3 Selecting the Card for Recording and Playback Standard Images will be recorded to the card selected with [Record/play]. Auto switch card Same as with the [Standard] setting, but if the card becomes full, the camera will automatically switch to the other card to record images.
Page 122 3 Selecting the Card for Recording and Playback Selecting the Card for Recording and Playback with Two Cards Inserted If [Record func.] is set to [Standard] or [Auto switch card], select the card for recording and playing images. If [Record func.] is set to [Rec. separately] or [Rec. to multiple], select the card for playing images.
Page 123: Setting The Image-Recording Quality
Setting the Image-Recording Quality You can set the image size (number of recorded pixels for JPEG/RAW) and JPEG quality (compression rate). H Selecting the Image Size 3, H, 5, or 6 will record the image as a JPEG image. With 1, 41, or 61, use Digital Photo Professional (provided software, p.426) to process the image after shooting.
Page 124 Setting the Image-Recording Quality Using the Menu Screen to Set the Image Size Select [Img type/size]. Under the [z2] tab, select [Img type/size], then press <0>. Set the image size. With [Standard / Auto switch card / Rec. to multiple] set: To select a RAW image size, turn the <6>...
Page 125 Setting the Image-Recording Quality Image Size Setting Examples 3 only 1 only If [–] is set for both RAW and JPEG, 3 will be set. The number of possible shots will be displayed up to 1999 on the top LCD panel and in the viewfinder.
Page 126 19 (20) The file size, possible shots, and maximum burst during continuous shooting are based on Canon’s 8 GB testing card and Canon’s testing standards (JPEG quality 8, ISO 100, and Standard Picture Style). These figures will vary depending on the subject, card brand, ISO speed, Picture Style, Custom Functions, and other settings.
Page 127 Setting the Image-Recording Quality If you select both RAW and JPEG, the same image will be recorded simultaneously to the card in both RAW and JPEG at the image- recording quality that was set. The two images will be recorded with the same file number (file extension .JPG for JPEG and .CR2 for RAW).
Page 128 Setting the Image-Recording Quality One-touch Image Quality Setting Custom Controls let you assign image-recording quality to the button, Multi-function button 2, or depth-of-field preview button with [One-touch image quality setting], so that you can temporarily switch image quality settings at the touch of a button before shooting. For details, see Custom Controls (p.343).
Page 129 Setting the Image-Recording Quality 3 Setting the JPEG Quality (Compression Rate) For JPEG images, the recording quality (compression rate) can be set separately for each image size: 3, H, 5, and 6. Select [JPEG quality]. Under the [z2] tab, select [JPEG quality], then press <0>.
Page 130: I: Setting The Iso Speed
i: Setting the ISO Speed Set the ISO speed (image sensor’s sensitivity to light) to suit the ambient light level. Regarding the ISO speed during movie shooting, see pages 230 and 232. Press the button. Set the ISO speed. While looking at the top LCD panel or in the viewfinder, turn the <6>...
Page 131: Iso Auto
i: Setting the ISO Speed As H1 (equivalent to ISO 102400) and H2 (equivalent to ISO 204800) are expanded ISO speed settings, noise (such as dots of light and banding) and irregular colors will be more noticeable, and the resolution will be lower than usual. If you use a high ISO speed and flash to shoot a close subject, overexposure may result.
Page 132 i: Setting the ISO Speed 3 Setting the ISO Speed Range You can set the manually-settable ISO speed range (minimum and maximum limits). You can set the minimum limit within L (ISO 50) to H1 (ISO 102400), and the maximum limit within ISO 100 to H2 (ISO 204800). Select [ISO speed settings].
Page 133: Setting The Iso Speed Range For Auto Iso
i: Setting the ISO Speed 3 Setting the ISO Speed Range for Auto ISO You can set the ISO speed range for Auto ISO within ISO 100 - 51200. You can set the minimum limit within ISO 100 - 25600, and the maximum limit within ISO 200 - 51200 in whole-stop increments.
Page 134: Setting The Minimum Shutter Speed For Auto Iso
i: Setting the ISO Speed 3 Setting the Minimum Shutter Speed for Auto ISO When Auto ISO is set, you can set the minimum shutter speed (1/8000 sec. to 1 sec.) so that the automatically-set shutter speed is not too slow.
Page 135: Selecting A Picture Style
Selecting a Picture Style By selecting a Picture Style, you can obtain image characteristics matching your photographic expression or the subject. Select [Picture Style]. Under [z1], select [Picture Style], then press <0>. The Picture Style selection screen will appear. Select a Picture Style. Turn the <5>...
Page 136 3 Selecting a Picture Style R Landscape For vivid blues and greens, and very sharp and crisp images. Effective for impressive landscapes. S Neutral This Picture Style is for users who prefer to process images with their computer. For natural colors and subdued images. U Faithful This Picture Style is for users who prefer to process images with their computer.
Page 137: About The Symbols
3 Selecting a Picture Style About the Symbols The symbols of the Picture Style selection screen refer to parameters such as [Sharpness] and [Contrast]. The numerals indicate the parameter settings, such as [Sharpness] and [Contrast], for each Picture Style. Symbols Sharpness Contrast Saturation...
Page 138: Customizing A Picture Style
Customizing a Picture Style You can customize a Picture Style by adjusting individual parameters such as [Sharpness] and [Contrast]. To see the resulting effects, take test shots. To customize [Monochrome], see page 140. Select [Picture Style]. Under [z1], select [Picture Style], then press <0>.
Page 139 3 Customizing a Picture Style Set the parameter. Turn the <5> dial to set the parameter as desired, then press <0>. Press the <M> button to save the adjusted parameters. The Picture Style selection screen will reappear. Any settings different from the default will be displayed in blue.
Page 140 3 Customizing a Picture Style V Monochrome Adjustment For Monochrome, you can also set [Filter effect] and [Toning effect] in addition to [Sharpness] and [Contrast] explained on the preceding page. kFilter Effect With a filter effect applied to a monochrome image, you can make white clouds or green trees stand out more.
Page 141: Registering A Picture Style
Registering a Picture Style You can select a base Picture Style such as [Portrait] or [Landscape], adjust its parameters as desired and register it under [User Def. 1], [User Def. 2], or [User Def. 3]. You can create Picture Styles whose parameter settings such as sharpness and contrast are different.
Page 142 3 Registering a Picture Style Select a parameter. Turn the <5> dial to select a parameter such as [Sharpness], then press <0>. Set the parameter. Turn the <5> dial to set the parameter as desired, then press <0>. For details, see “Customizing a Picture Style”...
Page 143: B: Setting The White Balance
B: Setting the White Balance White balance (WB) is for making the white areas look white. Normally, the <Q> (Auto) setting will obtain the correct white balance. If natural-looking colors cannot be obtained with <Q>, you can select the white balance that matches the light source or set it manually by shooting a white object.
Page 144: O Custom White Balance
O Custom White Balance Custom white balance enables you to manually set the white balance for a specific light source for better accuracy. Perform this procedure under the actual light source to be used. Up to five sets of Custom white balance data can be registered to the camera.
Page 145 O Custom White Balance Photograph a solid-white object. The plain, white object should fill the spot metering circle. Focus manually and set the standard exposure for the white object. Any white balance setting can be set. Spot metering circle The Custom WB data will be registered.
Page 146 O Custom White Balance Select image on card First follow step 4 under “Record and register WB” (p.144) to take a picture of a plain, white object. This image saved in the card can then be registered for Custom WB. The procedure up to step 2 is the same as in “Record and register WB.”...
Page 147 O Custom White Balance 3 Selecting and Shooting with the Custom WB Data Select the Custom WB Number. Registered image On the Custom WB registration screen, select the number of the registered Custom WB. Select [Set as white balance]. Turn the <5> dial to select [Set as white balance], then press <0>.
Page 148: Enter Text
O Custom White Balance Select [Edit WB name]. Turn the <5> dial to select [Edit WB name], then press <0>. Enter text. Press the <Q> button, and the text palette will be highlighted in a color frame. Text can be entered. Operate the <5/6>...
Page 149: P Setting The Color Temperature
P Setting the Color Temperature You can set the white balance’s color temperature numerically in Kelvins. This function is for advanced users. Press the button. Select . Look at the top LCD panel and turn the <5> dial to select . Set the color temperature.
Page 150: White Balance Correction
u White Balance Correction You can correct the white balance that has been set. This adjustment will have the same effect as using a commercially-available color temperature conversion filter or color compensating filter. Each color can be corrected to one of nine levels. This function is for advanced users who are familiar with using color temperature conversion or color compensating filters.
Page 151: White Balance Auto Bracketing
u White Balance Correction White Balance Auto Bracketing With just one shot, three images having a different color balance can be recorded simultaneously. Based on the color temperature of the current white balance setting, the image will be bracketed with a blue/amber bias or magenta/green bias.
Page 152: Correcting The Brightness And Contrast Automatically (Auto Lighting Optimizer)
Correcting the Brightness and Contrast Automatically If the image comes out dark or the contrast is low, the brightness and contrast can be corrected automatically. This function is called Auto Lighting Optimizer. The default setting is [Standard]. With JPEG images, the correction is applied when the image is captured. Select [Auto Lighting Optimizer].
Page 153: Noise Reduction Settings
Noise Reduction Settings High ISO Speed Noise Reduction This function reduces the noise generated in the image. Although noise reduction is applied at all ISO speeds, it is particularly effective at high ISO speeds. At low ISO speeds, the noise in darker parts of the image is further reduced.
Page 154 3 Noise Reduction Settings Long Exposure Noise Reduction Noise reduction is possible with images exposed for 1 sec. or longer. Select [Long exp. noise reduction]. Under the [z2] tab, select [Long exp. noise reduction], then press <0>. Set the desired setting. Turn the <5>...
Page 155 3 Noise Reduction Settings With [Auto] and [Enable], after the picture is taken, the noise reduction process may take the same amount of time as the exposure. During noise reduction, shooting is still possible as long as the maximum burst indicator in the viewfinder shows “1”...
Page 156: Highlight Tone Priority
Highlight Tone Priority You can minimize overexposed highlight areas. Select [Highlight tone priority]. Under the [z2] tab, select [Highlight tone priority], then press <0>. Select [Enable]. Turn the <5> dial to select [Enable], then press <0>. Highlight details are improved. The dynamic range is expanded from the standard 18% gray to bright highlights.
Page 157: Lens Peripheral Illumination / Chromatic Aberration Correction
Lens Peripheral Illumination / Chromatic Aberration Correction Peripheral light fall-off occurs in lenses whose characteristics make the image corners look darker. Color fringing along subject outlines is another chromatic aberration. Both lens aberrations can be corrected. The default setting is [Enable] for both corrections. Peripheral Illumination Correction Select [Lens aberration correction].
Page 158: Chromatic Aberration Correction
3 Lens Peripheral Illumination / Chromatic Aberration Correction Chromatic Aberration Correction Select the setting. Check that [Correction data available] is displayed for the attached lens. Turn the <5> dial to select [Chromatic aberration], then press <0>. Select [Enable], then press <0>. If [Correction data not available] is displayed, see “About the Lens Correction Data”...
Page 159 Corrections cannot be applied afterwards to JPEG images captured when [Disable] was set. When using a non-Canon lens, setting the corrections to [Disable] is recommended, even if [Correction data available] is displayed. If you use the magnified view during Live View shooting, the peripheral illumination correction and chromatic aberration correction will not be reflected in the image.
Page 160: Creating And Selecting A Folder
Creating and Selecting a Folder You can freely create and select the folder where the captured images are to be saved. This operation is optional since a folder will be created automatically for saving captured images. Creating a Folder Select [Record func+card/folder sel.].
Page 161: Selecting A Folder
3 Creating and Selecting a Folder Selecting a Folder With the folder selection screen Lowest file number displayed, turn the <5> dial to select Number of images in folder the desired folder, then press <0>. The folder where the captured images will be saved is selected.
Page 162: Changing The File Name
Changing the File Name The file name has four alphanumeric characters followed by a four-digit image number (p.164) and BE3B0001.JPG (Ex.) extension. The first four alphanumeric characters are set upon factory shipment and unique to the camera. However, you can change them. With “User setting1”, you can change and register the four characters as desired.
Page 163 3 Changing the File Name Exit the setting. Enter the required number of alphanumeric characters, then press the <M> button. The new file name will be registered and the screen in step 2 will reappear. Select the registered file name. Turn the <5>...
Page 164: File Numbering Methods
File Numbering Methods The four-digit file number is like the frame number on a roll of film. The captured images BE3B0001.JPG (Ex.) are assigned a sequential file number from 0001 to 9999 and saved in one folder. You can change how the file number is assigned. Select [File numbering].
Page 165: Auto Reset
3 File Numbering Methods Auto Reset The file numbering restarts from 0001 each time the card is replaced or a new folder is created. When you replace the card, create a folder, or switch the target card (such as f → g), the file numbering restarts from 0001 for the new images saved.
Page 166: Setting Copyright Information
Setting Copyright Information When you set the copyright information, it will be recorded to the image as Exif information. Select [Copyright information]. Under the [54] tab, select [Copyright information], then press <0>. Select the option to be set. Turn the <5> dial, select either [Enter author’s name] or [Enter copyright details], then press <0>.
Page 167 3 Setting Copyright Information Checking the Copyright Information When you select [Display copyright info.] in step 2 on the preceding page, you can check the [Author] and [Copyright] information that you entered. Deleting the Copyright Information When you select [Delete copyright information] in step 2, you can delete the [Author] and [Copyright] information.
Page 168: Setting The Color Space
Setting the Color Space The range of reproducible colors is called the color space. With this camera, the color space for captured images can be set to sRGB or Adobe RGB. For normal shooting, sRGB is recommended. Select [Color space]. Under the [z1] tab, select [Color space], then press <0>.
Page 169: Exposure Control
Exposure Control Select the shooting mode to suit the subject or shooting objective. You can set the shutter speed and/or aperture to obtain the exposure you want. After you press the shutter button halfway and let go, the exposure values will remain displayed in the viewfinder and on the top LCD panel for approx.
Page 170: D: Program Ae
d: Program AE The camera automatically sets the shutter speed and aperture to suit the subject’s brightness. This is called Program AE. * <d> stands for Program. * AE stands for autoexposure. Set the shooting mode to <d>. Press the <W> button and turn the <6>...
Page 171 d: Program AE Take the picture. Compose the shot and press the shutter button completely. If the “30"” shutter speed and the maximum aperture blink, it indicates underexposure. Increase the ISO speed or use flash. If the “8000” shutter speed and the minimum aperture blink, it indicates overexposure.
Page 172 The shutter speed and aperture displays are blinking. Since it is too dark, taking the picture may result in a blurred subject due to camera shake. Using a tripod or a Canon EX-series Speedlite (p.196) (sold separately) is recommended. When flash was used, the bottom part of the picture came out unnaturally dark.
Page 173: S: Shutter-Priority Ae
s: Shutter-Priority AE In this mode, you set the shutter speed and the camera automatically sets the aperture to obtain the standard exposure suiting the brightness of the subject. This is called shutter-priority AE. A faster shutter speed can freeze the action or a moving subject. A slower shutter speed can create a blurred effect, giving the impression of motion.
Page 174 s: Shutter-Priority AE If the maximum aperture blinks, it indicates underexposure. Turn the <6> dial to set a slower shutter speed until the aperture stops blinking or set a higher ISO speed. If the minimum aperture blinks, it indicates overexposure. Turn the <6>...
Page 175: F: Aperture-Priority Ae
f: Aperture-Priority AE In this mode, you set the desired aperture and the camera sets the shutter speed automatically to obtain the standard exposure suiting the subject brightness. This is called aperture-priority AE. A higher f/number (smaller aperture hole) will make more of the foreground and background fall within acceptable focus.
Page 176: Depth Of Field Preview
f: Aperture-Priority AE If the “30"” shutter speed blinks, it indicates underexposure. Turn the <6> dial to set a larger aperture (lower f/number) until the shutter speed blinking stops or set a higher ISO speed. If the “8000” shutter speed blinks, it indicates overexposure.
Page 177: A: Manual Exposure
a: Manual Exposure In this mode, you set both the shutter speed and aperture as desired. To determine the exposure, refer to the exposure level indicator in the viewfinder or use a commercially-available exposure meter. This method is called manual exposure. * <a>...
Page 178 a: Manual Exposure Set the exposure. Check the exposure level and set the desired shutter speed and aperture. If the difference with the standard exposure exceeds ±3 stops, the end of the exposure level indicator will display < > or < >.
Page 179: Selecting The Metering Mode
q Selecting the Metering Mode You can select one of four methods to measure the subject’s brightness. Press the <Q> button. Select the metering mode. While looking at the top LCD panel, turn the <6> dial. q: Evaluative metering w: Partial metering r: Spot metering e: Center-weighted average metering q Evaluative metering...
Page 180 q Selecting the Metering Mode Multi-Spot Metering With multiple spot meter readings, you can see the relative exposure levels of multiple areas in the picture and set the exposure to obtain the desired result. Multi-spot metering is possible in d/s/f modes. Set the metering mode to r spot metering.
Page 181: O Setting Exposure Compensation
O Setting Exposure Compensation Exposure compensation can brighten (increased exposure) or darken (decreased exposure) the standard exposure set by the camera. Exposure compensation can be set in the d/s/f shooting modes. Although you can set the exposure compensation up to ±5 stops in 1/3-stop increments, the exposure compensation indicator in the viewfinder and on the top LCD panel can only display the setting up to ±3 stops.
Page 182: Auto Exposure Bracketing (Aeb)
h Auto Exposure Bracketing (AEB) By changing the shutter speed or aperture automatically, the camera brackets the exposure up to ±3 stops in 1/3-stop increments for three successive shots. This is called AEB. * AEB stands for Auto Exposure Bracketing. Hold down the <W>...
Page 183: Ae Lock Effects
A AE Lock Use AE lock when the area of focus is to be different from the exposure metering area or when you want to take multiple shots at the same exposure setting. Press the <A> button to lock the exposure, then recompose and take the shot.
Page 184: Bulb Exposures
Bulb Exposures When bulb shooting is set, the shutter stays open as long as you hold down the shutter button completely, and closes when you let go of the shutter button. Use bulb exposures for night scenes, fireworks, the heavens, and other subjects requiring long exposures. Set the shooting mode to <buLb>.
Page 185: F Using A Remote Switch
Bulb Exposures Using the Eyepiece Shutter If you use the self-timer or bulb and take a picture without looking through the viewfinder, stray light entering the eyepiece can throw off the exposure and result in a dark picture. To prevent this, slide the eyepiece shutter lever as shown by the arrow to shutter the eyepiece.
Page 186: P Multiple Exposures
P Multiple Exposures You can shoot two to nine exposures to be merged into one image. If you shoot multiple-exposure images with Live View shooting (p.205), you can see how the single exposures merge while shooting. Select [Multiple exposure]. Under [z1], select [Multiple exposure] then press <0>.
Page 187 P Multiple Exposures Set [Multi-expos ctrl]. Select the desired multiple-exposure control method, then press <0>. Additive The exposure of each single exposure is added cumulatively. Based on the [No. of exposures], set a negative exposure compensation. Refer to the basic guide below to set a negative exposure compensation. Exposure Compensation Setting Guide for Multiple Exposures Two exposures: -1 stop, three exposures: -1.5 stop, four exposures: -2 stops If [On:Func/Ctrl] and [Additive] are both set, the image displayed...
Page 188 P Multiple Exposures Set the images to be saved. To save all the single exposures and the merged multiple-exposure image, select [All images], then press <0>. To save only the merged multiple- exposure image, select [Result only], then press <0>. Select [Continue Mult-exp].
Page 189 P Multiple Exposures Shoot subsequent exposures. When [On:Func/Ctrl] is set, the merged multiple-exposure image will be displayed. With Live View shooting, the multiple-exposure images merged so far will be displayed. By pressing the button, you can display only the Live View image. After you shoot the set number of exposures, multiple-exposure shooting will be canceled.
Page 190 P Multiple Exposures Merging Multiple Exposures with an Image Recorded in the Card You can select an image recorded in the card as the first single exposure. The original of the selected image will remain intact. You can only select 1 images. You cannot select 41/61 or JPEG images.
Page 191 P Multiple Exposures You can also select a 1 multiple-exposure image. If you select [Deselect img], the selected image will be canceled. Checking and Deleting Multiple Exposures During Shooting When [On:Func/Ctrl] is set and you have not finished shooting the set number of exposures, you can press the <x>...
Page 192 P Multiple Exposures Are there any restrictions on the image-recording quality? All JPEG image-recording quality settings can be selected. If 41 or 61 is set, the merged multiple-exposure will be recorded as a 1 image. Image-Recording Merged Multiple- Single Exposures Quality Setting Exposure JPEG...
Page 193: Mirror Lockup
2 Mirror Lockup Although using the self-timer or Remote Switch can prevent camera shake, using mirror lockup to prevent camera vibrations (mirror shock) can also help when you use a super telephoto lens or shoot close ups (macro photography). Set [Mirror lockup]. Under the [z3] tab, select [Mirror lockup], then press <0>.
Page 194 2 Mirror Lockup In very bright light such as at the beach or a ski slope on a sunny day, take the picture promptly after mirror lockup. Do not point the camera toward the sun. The sun’s heat can scorch and damage the shutter curtains.
Page 195: Flash Photography
Flash Photography This chapter explains how to shoot with an EOS- dedicated, EX-series Speedlite (sold separately) or non- Canon flash unit and how to set flash functions on the camera’s menu screen.
Page 196: D Flash Photography
D Flash Photography EOS-dedicated, EX-series Speedlites An EX-series Speedlite (sold separately) makes flash photography as easy as normal shooting. For detailed instructions, refer to the EX-series Speedlite’s instruction manual. This camera is a Type-A camera that can use all the features of EX-series Speedlites. To set the flash functions and flash Custom Functions with the camera’s menu, see pages 199-204.
Page 197 Cautions for Live View shooting If you use a non-Canon flash unit with Live View shooting, set [z4: Silent LV shoot.] to [Disable] (p.214). The flash will not fire if it is set to [Mode 1] or [Mode 2].
Page 198 D Flash Photography If the camera is used with a flash unit or flash accessory dedicated to another camera brand, the camera may not operate properly and malfunction may result. Do not connect to the camera’s PC terminal any flash unit requiring 250 V or more.
Page 199: Setting The Flash
Setting the Flash With an EX-series Speedlite having compatible flash function settings, you can use the camera’s menu screen to set the Speedlite’s functions and Custom Functions. Attach the Speedlite to the camera and turn on the Speedlite. For details on the Speedlite’s functions, refer to the Speedlite’s instruction manual.
Page 200 3 Setting the Flash [Flash sync. speed in Av mode] You can set the flash-sync speed for flash photography in the aperture-priority AE (f) mode. : Auto The flash sync speed is set automatically within a range of 1/250 sec. to 30 sec. to suit the scene’s brightness. High-speed sync is also possible.
Page 201: Flash Function Settings
3 Setting the Flash [Flash function settings] The information and available functions displayed on the screen will differ depending on the Speedlite, current flash mode, flash Custom Function settings, etc. For details on your Speedlite’s flash functions, refer to the Speedlite’s instruction manual.
Page 202 3 Setting the Flash Wireless functions Wireless (multiple) flash shooting is possible with radio or optical transmission. For details on wireless flash, refer to the Speedlite’s instruction manual. Flash zoom (Flash coverage) With Speedlites having a zooming flash head, you can set the flash coverage. Normally, set this to [AUTO] so that the camera will automatically set the flash coverage to match the lens focal length.
Page 203 3 Setting the Flash Flash exposure compensation The same setting as “Flash exposure compensation” on page 196 can be set. For details, refer to the Speedlite’s instruction manual. Flash exposure bracketing While the flash output is changed automatically, three shots are taken. For details on FEB (Flash Exposure Bracketing), refer to the Speedlite’s instruction manual.
Page 204: Flash Custom Function Settings
3 Setting the Flash Flash Custom Function Settings For details on the Speedlite’s Custom Functions, refer to the Speedlite’s instruction manual. Select [Flash C.Fn settings]. Select [Flash C.Fn settings], then press <0>. Set the functions. Turn the <5> dial to select the number, then press <0>.
Page 205: Shooting With The Lcd Monitor
Shooting with the LCD Monitor (Live View Shooting) You can shoot while viewing the image on the camera’s LCD monitor. This is called “Live View shooting”. Live View shooting is effective for photos of still subjects. If you handhold the camera and shoot while viewing the LCD monitor, camera shake can cause blurred images.
Page 206: A Preparing For Live View Shooting
A Preparing for Live View Shooting During Live View shooting, you can take still photos. To shoot movies, see page 225. Select [LV z/k set.]. Under the [z4] tab, select [LV z/ k set.], then press <0>. “LV” stands for Live View. Select [Stills].
Page 207: A Shooting With The Lcd Monitor
A Shooting with the LCD Monitor Select the shooting mode. Press the <W> button and turn the <6> or <5> dial to select the shooting mode. Focus the subject. When you press the shutter button halfway, the camera will focus with the current AF mode (p.215).
Page 208 A Shooting with the LCD Monitor Battery Life with Live View Shooting [Approx. number of shots] Temperature At 23°C / 73°F At 0°C / 32°F Possible shots The figures above are based on a fully-charged Battery Pack LP-E4N and CIPA (Camera & Imaging Products Association) testing standards. With a fully-charged Battery Pack LP-E4N, continuous Live View shooting is possible for approx.
Page 209 A Shooting with the LCD Monitor About the Information Display Each time you press the button, the information display will change. AF mode Auto Lighting Optimizer •d : Live mode •c : Face detection Live AF point (Live mode) mode •f : Quick mode Shooting mode...
Page 210 A Shooting with the LCD Monitor Final Image Simulation The final image simulation reflects the effects of the Picture Style, white balance, etc., in the Live View image so you can see what the captured image will look like. During shooting, the Live View image will automatically reflect the function settings listed below.
Page 211: Shooting Function Settings
Shooting Function Settings W / f / R / y / S / i / O / B Settings While the Live View image is displayed, if you press the <W>, <o>, <Q>, <S>, , <O>, or button, the setting screen will appear on the LCD monitor and you can turn the <6>...
Page 212: Menu Function Settings
Menu Function Settings Function settings particular to Live View shooting are explained here. The menu options under the [z4] tab are explained on pages 212-214. The functions settable on this menu screen only apply during Live View shooting. These functions do not take effect during viewfinder shooting.
Page 213 3 Menu Function Settings Exposure simulation Exposure simulation displays and simulates how the brightness of the actual image (exposure) will look. • Enable (g) The displayed image brightness will be close to the actual brightness (exposure) of the resulting image. If you set exposure compensation, the image brightness will change accordingly.
Page 214 If you use flash, silent shooting will not be possible regardless of the [Silent LV shoot.] setting. When using a non-Canon flash unit, set this function to [Disable]. The flash will not fire if it is set to [Mode 1] or [Mode 2].
Page 215: Using Af To Focus
Using AF to Focus Selecting the AF Mode The AF modes available are [Live mode], [u Live mode] (face detection, p.216), and [Quick mode] (p.220). If you want to achieve precise focus, set the lens focus mode switch to <MF>, magnify the image, and focus manually (p.222). Select the AF mode.
Page 216 Using AF to Focus Focus the subject. Aim the AF point over the subject and press the shutter button halfway. When focus is achieved, the AF point will turn green and the beeper will sound. If focus is not achieved, the AF point will turn orange.
Page 217 Using AF to Focus Focus the subject. Press the shutter button halfway and the camera will focus the face covered by the frame. When focus is achieved, the AF point will turn green and the beeper will sound. If focus is not achieved, the AF point will turn orange.
Page 218 Using AF to Focus Live Mode and u (Face Detection) Live Mode Notes AF operation Focusing will take slightly longer. Even when focus has been achieved, pressing the shutter button halfway will focus again. The image brightness may change during and after the AF operation.
Page 219 EF50mm f/1.4 USM, EF50mm f/1.8 II, EF50mm f/2.5 Compact Macro, EF75-300mm f/4-5.6 III, EF75-300mm f/4-5.6 III USM For information on discontinued lenses, refer to your local Canon Web site.
Page 220 Using AF to Focus Quick Mode: f The dedicated AF sensor is used to focus in One-Shot AF mode (p.67), using the same AF method as with viewfinder shooting. Although you can focus the target area quickly, the Live View image will be interrupted momentarily during the AF operation.
Page 221 Using AF to Focus Select the AF point. Use the <9> to select an AF point. If you press <9> straight down, the center AF point (or center Zone) will be selected. You can also use the <6> and <5> dials to select the AF point. The <6>...
Page 222: Focusing Manually
Focusing Manually You can magnify the image and focus precisely with manual focus. Set the lens focus mode switch to <MF>. Turn the lens focusing ring to focus roughly. Move the magnifying frame. Use <9> to move the magnifying frame to the position where you want to focus.
Page 223 Live View Shooting Cautions Image Quality When you shoot at high ISO speeds, noise (such as dots of light and banding) may become noticeable. Shooting in high temperatures may cause noise and irregular colors in the image. If Live View shooting is used continuously for a long period, the camera’s internal temperature may rise, degrading image quality.
Page 224 Live View Shooting Cautions Live View Image Under low- or bright-light conditions, the Live View image may not reflect the brightness of the captured image. If the light source within the image changes, the screen may flicker. If this happens, exit Live View shooting and resume shooting under the actual light source to be used.
Page 225: Shooting Movies
Shooting Movies The live image displayed on the camera’s LCD monitor can be recorded as a movie to the card. The movie recording format will be MOV. Cards that Can Record Movies When shooting movies, use a large-capacity card with a fast writing/reading speed as shown in the table.
Page 226: Preparing To Shoot Movies
k Preparing to Shoot Movies Set the camera so it can record the live image displayed on the LCD monitor as a movie. To shoot still photos, see page 205. Select [LV z/k set.]. Under the [z4] tab, select [LV z/ k set.], then press <0>.
Page 227: Shooting Movies
k Shooting Movies Autoexposure Shooting When the shooting mode is set to <d> or <BULB>, autoexposure control will take effect to suit the scene’s current brightness. Autoexposure control will be the same for <d> and <BULB>. Set the shooting mode to <d/ BULB>.
Page 228: Shutter-Priority Ae
k Shooting Movies Shutter-priority AE When the shooting mode is <s>, you can manually set the shutter speed for movie shooting. The ISO speed and aperture will be set automatically to suit the brightness and obtain a standard exposure. Set the shooting mode to <s>. Press the <W>...
Page 229: Aperture-Priority Ae
k Shooting Movies Aperture-priority AE When the shooting mode is <f>, you can manually set the aperture for movie shooting. The ISO speed and shutter speed will be set automatically to suit the brightness and obtain a standard exposure. Set the shooting mode to <f>. Press the <W>...
Page 230 k Shooting Movies ISO speed in the d, s, f, and BULB modes The ISO speed will be set automatically within ISO 100 - 25600. Under [z2: ISO speed settings], if [ISO speed range]’s [Maximum] setting (p.132) is set to [51200/H] in the d, s, and BULB modes, the automatic ISO speed setting range’s maximum will be expanded to H (equivalent to ISO 51200).
Page 231: Manual Exposure Shooting
k Shooting Movies Manual Exposure Shooting You can manually set the shutter speed, aperture, and ISO speed for movie shooting. Using manual exposure to shoot movies is for advanced users. Set the shooting mode to <a>. Press the <W> button and turn the <6>...
Page 232 k Shooting Movies ISO speed during manual-exposure shooting With [Auto] (A), the ISO speed will be set automatically within ISO 100 - 25600. You can set the ISO speed manually within ISO 100 - 25600 in 1/3- stop increments. Under [z2: ISO speed settings], if [ISO speed range]’s [Maximum] is set to [51200/H], the manual ISO speed setting range’s maximum will be expanded to H (equivalent to ISO 51200).
Page 233: Information Display
k Shooting Movies Information Display Each time you press the button, the information display will change. AF mode Picture Style •d: Live mode •c : Face detection Time code Live mode AF point (Live mode) •f:Quick mode Shooting mode Drive mode Recording movie White balance...
Page 234 k Shooting Movies Notes on Movie Shooting The camera cannot autofocus continuously like a camcorder. Autofocusing during movie shooting may momentarily throw the focus far off or change the exposure. When you autofocus during movie shooting under low-light conditions using a USM lens, horizontal stripes (noise) may be recorded. Note that with certain lenses equipped with the electronic focusing ring, similar noise may be recorded even with manual focusing (MF).
Page 235 k Shooting Movies Notes on Movie Shooting Under [z5: Movie shoot. btn], if [V/o] is selected, you can press the shutter button completely to start or stop the movie shooting (p.248). Monaural sound is recorded by the camera’s built-in microphone (p.227). By connecting a stereo microphone (commercially available) equipped with a 3.5 mm mini plug to the camera’s external microphone IN terminal (p.21), stereo sound recording is possible.
Page 236: Shooting Still Photos
k Shooting Movies Shooting Still Photos While shooting a movie, you can also take a still photo by pressing the shutter button completely. Taking still photos during movie shooting If you take a still photo during movie shooting, the movie will record a still moment lasting approx.
Page 237 k Shooting Movies AEB cannot be used. Even if an external Speedlite is used, it will not fire. Continuous still photo shooting is possible during movie shooting. However, the captured images will not be displayed on the screen. Depending on the still photo’s image-recording quality, number of shots during continuous shooting, card performance, etc., the movie shooting may stop automatically.
Page 238: Shooting Function Settings
Shooting Function Settings W / f / R / S / i / O / B Settings If you press the <W>, <o>, <S>, , <O>, or button while the image is displayed on the LCD monitor, the setting screen will appear on the LCD monitor and you can turn the <6>...
Page 239: Setting The Movie-Recording Size
Setting the Movie-Recording Size With [z4: Movie rec. size], you can set the movie’s image size, frame rate per second, and compression method. The frame rate switches automatically depending on the [53: Video system] setting. Image size A [1920x1080] : Full High-Definition (Full HD) recording quality. The aspect ratio will be 16:9.
Page 240 3 Setting the Movie-Recording Size Total Movie Recording Time and File Size Per Minute Total Recording Time (approx.) Movie-Recording File Size Size (approx.) 4 GB Card 8 GB Card 16 GB Card 654 X 16 min. 32 min. 1 hr. 4 min. 235 MB/min.
Page 241 3 Setting the Movie-Recording Size An increase of the camera’s internal temperature may cause movie shooting to stop before the maximum recording time shown on the preceding page (p.249). Even if [Record func.] is set to [Auto switch card], the card cannot be switched automatically during movie shooting.
Page 242: Setting The Sound Recording
Setting the Sound Recording You can shoot movies while recording sound with the built-in monaural microphone or with a commercially- available stereo microphone. You can also freely adjust the sound-recording level. Set the sound recording with [z4: Sound recording]. Sound Recording/Sound-Recording Level [Auto] : The sound-recording level is adjusted automatically.
Page 243 3 Setting the Sound Recording Using the microphone The built-in microphone records monaural sound. Stereo sound recording is possible by connecting an external stereo microphone (commercially-available) equipped with a miniature stereo plug (3.5 mm) to the camera’s external microphone IN terminal (p.21). When an external microphone is connected, sound recording will switch automatically to the external microphone.
Page 244: Silent Control
Silent Control This function is convenient when you want to change the ISO speed, sound-recording level, etc., silently while shooting a movie. When [z5: Silent Control] is set to [Enable h], you can use the touch pad <h> on the inner ring of the Quick Control Dial.
Page 245: Setting The Time Code
Setting the Time Code The time code is a time reference recorded automatically to synchronize the video and audio during movie shooting. It is recorded at all times in the following units: hours, minutes, seconds, and frames. It is mainly used during movie editing.
Page 246 3 Setting the Time Code Regardless of the [Movie rec count] setting, the time code will always be recorded to the movie file. Movie Playback Count You can select what to display on the movie playback screen. [Rec time] : Displays the recording time and playback time during movie playback.
Page 247: Menu Function Settings
Menu Function Settings [z4] Menu When you select [Movies] under [z4: LV z/k set.], the [z4] [z5] tabs for movie shooting will appear. The menu options are as follows. AF mode The AF modes will be the same as described on pages 215-221. You can select [Live mode], [u Live mode], or [Quick mode].
Page 248 3 Menu Function Settings Silent LV shooting This function applies to still photo shooting. For details, see page 214. Metering timer You can change how long the exposure settings are displayed (AE lock time). [z5] Menu Time code You can set the time code. For details, see pages 245 and 246. Silent Control When [Enable h] is set, you can use the touch pad <h>...
Page 249 Movie Shooting Cautions White <s> and Red <E> Internal Temperature Warning Icons If the camera’s internal temperature increases due to prolonged movie shooting or a high ambient temperature, a white icon <s> will appear. Even if you shoot a movie while this icon is displayed, the movie’s image quality will hardly be affected.
Page 250 Movie Shooting Cautions Recording and Image Quality If you use a card with a slow writing speed, a five-level indicator may appear on the right of the screen during movie shooting. It indicates how much data has not yet been written to the card (remaining capacity of the internal buffer memory).
Page 251: Image Playback
Image Playback This chapter explains how to play back and erase photos and movies, how to display them on a TV screen, and other playback-related functions. About images taken with another camera The camera may not be able to properly display images captured with a different camera or edited with a computer or whose file name was changed.
Page 252: Image Playback
x Image Playback Single-Image Display Play back the image. Press the <x> button. The last captured image or last image viewed will appear. Select an image. To play back images starting with the last image, turn the <5> dial counterclockwise. To play back images starting with the first captured image, turn the dial clockwise.
Page 253: Grid Display
x Image Playback Exit the image playback. Press the <x> button to exit the image playback and return to shooting-ready state. 3 Grid Display With single-image display, you can overlay the grid on the image during playback. With [33: Playback grid], you can select [3x3 l], [6x4 m], or [3x3+diag This function is convenient for checking the image’s tilt and composition.
Page 254: B: Shooting Information Display
B: Shooting Information Display Sample Information for Still Photos AF Microadjustment Protect images Rating Exposure compensation amount Voice memo Flash exposure Folder number - File number compensation amount Card Aperture Histogram Shutter speed (Brightness/RGB) FE Microadjustment Metering mode Shooting mode AE Microadjustment ISO speed Color temperature...
Page 255 B: Shooting Information Display Sample Information for Movies Shooting time, Playback time/Time code Playback Shutter speed Aperture Shooting mode Movie recording Movie file size size Frame rate Compression method About the Highlight Alert When [33: Highlight alert] is set to [Enable], overexposed highlight areas will blink.
Page 256 B: Shooting Information Display About the Histogram The brightness histogram shows the exposure level distribution and overall brightness. The RGB histogram is for checking the color saturation and gradation. The display can be switched with [33: Histogram]. [Brightness] Display Sample Histograms This histogram is a graph showing the distribution of the image’s brightness level.
Page 257: Hi Searching For Images Quickly
x Searching for Images Quickly H Display Multiple Images on One Screen (Index Display) You can search for images quickly with the index display showing four or nine images on one screen. Press the button. During image playback, press the ...
Page 258 x Searching for Images Quickly Jump through Images (Jump Display) With the single-image display, you can turn the <6> dial to jump through the images forward or backward according to the jump method set. Select [Image jump w/6]. Under the [32] tab, select [Image jump w/6], then press <0>.
Page 259: Magnified View
u Magnified View You can magnify a captured image by approx. 1.5x to 10x on the LCD monitor. Magnify the image. The image can be magnified during image playback (single-image display), during image review after image capture, and from shooting- ready state.
Page 260 u Magnified View 3 Magnification Settings Under the [33] tab, when you select [Magnificatn (apx)], you can set the starting magnification and initial position for the magnified view. 1x (no magnification) The image will not be magnified. The magnified view will start with the single-image display.
Page 261: Rotating The Image
b Rotating the Image You can rotate the displayed image to the desired orientation. Select [Rotate image]. Under the [31] tab, select [Rotate image], then press <0>. Select an image. Turn the <5> dial to select the image to be rotated. You can also select an image on the index display (p.257).
Page 262: Setting Ratings
Setting Ratings You can rate images and movies with one of five rating marks: l/m/ n/o/p. This function is called rating. 3 Set Ratings with the Menu Select [Rating]. Under the [32] tab, select [Rating], then press <0>. Select an image or movie. Turn the <5>...
Page 263 Setting Ratings Using the <J> Button Under [85:J/Kbutton function], if you set [Rating (J and K disabled)] (p.338), you can press the <J> button to rate images/ movies during playback. Set the < > button’s function. Set [85:J/Kbutton function] to [Rating (J and Kdisabled)].
Page 264: Q Quick Control During Playback
Q Quick Control During Playback During playback, you can press the <Q> button to set the following: [K: Protect images, b: Rotate image, 9: Rating, R: RAW image processing (RAW images only), S: Resize (JPEG image only), : AF point display, e: Image jump w/6]. Highlight alert, For movies, only the functions in bold above can be set.
Page 265 Q Quick Control During Playback To rotate an image, set [51: Auto rotate] to [OnzD]. If [51: Auto rotate] is set to [OnD] or [Off], the [b Rotate image] setting will be recorded to the image, but the camera will not rotate the image for display. Press the <Q>...
Page 266: Enjoying Movies
k Enjoying Movies You can play back movies in the following three ways: Playback on a TV set (p.275, 278) Use the provided AV cable or an HDMI Cable HTC-100 (sold separately) to connect the camera to a TV set. Then you can play back captured movies and still photos on the TV.
Page 267 k Enjoying Movies Playback and Editing with a Personal Computer (p.426) The movie files recorded on the card can be transferred to a personal computer and played with ImageBrowser EX. To have the movie play back smoothly on a personal computer, use a high-performance personal computer.
Page 268: Playing Movies
k Playing Movies Play back the image. Press the <x> button to display images. Select a movie. Turn the <5> dial to select the movie to be played. With the single-image display, the <1s> icon displayed on the upper left indicates a movie. In the index display, perforations at the left edge of a thumbnail indicate a movie.
Page 269 k Playing Movies Function Playback Description 2 Exit Returns to the single-image display. 7 Play Pressing <0> toggles between play and stop. Adjust the slow motion speed by turning the <5> dial. The 8 Slow motion slow-motion speed is indicated at the upper right of the screen.
Page 270: Editing The Movie's First And Last Scenes
X Editing the Movie’s First and Last Scenes You can edit out the first and last scenes of a movie in 1-sec. increments. On the movie playback screen, select [X]. The movie editing panel will be displayed at the bottom of the screen. Specify the part to be edited out.
Page 271 X Editing the Movie’s First and Last Scenes Save the movie. Select [W], then press <0>. The save screen will appear. To save it as a new movie, select [New file]. To save it and overwrite the original movie file, select [Overwrite].
Page 272: Slide Show (Auto Playback)
Slide Show (Auto Playback) You can play back the images on the card as an automatic slide show. Select [Slide show]. Under the [32] tab, select [Slide show], then press <0>. Select the images to be played. Number of images to be played Turn the <5>...
Page 273 3 Slide Show (Auto Playback) Item Playback Description All the still photos and movies on the card will be played jAll images back. Still photos and movies taken on the selected shooting iDate date will be played back. Still photos and movies in the selected folder will be nFolder played back.
Page 274: Start The Slide Show
3 Slide Show (Auto Playback) Start the slide show. Turn the <5> dial to select [Start], then press <0>. After [Loading image...] is displayed, the slide show will start. Quit the slide show. To quit the slide show and return to the setting screen, press the <M>...
Page 275: Viewing The Images On Tv
Viewing the Images on TV You can view the still photos and movies on a TV set. Adjust the movie’s sound volume with the TV set. The sound volume cannot be adjusted with the camera. Before connecting or disconnecting the cable between the camera and television, turn off the camera and TV set.
Page 276 Viewing the Images on TV Press the <x> button. The image will appear on the TV screen. (Nothing will be displayed on the camera’s LCD monitor.) The images will automatically be displayed at the TV’s optimum resolution. By pressing the button, you can change the display format.
Page 277 Viewing the Images on TV Connect the camera to a TV set. Use an HDMI cable to connect the camera to the TV. The TV’s input will switch automatically to the HDMI port connected to the camera. Press the camera’s <x> button. An image will appear on the TV screen and you can use the TV’s remote control to play back images.
Page 278 Viewing the Images on TV Viewing on Non High-Definition (HD) TV Sets Connect the provided AV cable to the camera. With the plug’s <Canon> logo facing the back of the camera, insert it into the <q> terminal. Connect the AV cable to the TV (Red) set.
Page 279: J Protecting Images
J Protecting Images Protecting an image prevents it from being erased accidentally. Protecting Images Individually with the <J> Button Select the image to be protected. Press the <3> button to play back images, then turn the <5> dial to select the image. Protect the image.
Page 280: Protecting All Images In A Folder Or Card
J Protecting Images Protect the image. Turn the <5> dial to select the image to be protected, then press <0>. The image will be protected, and the <K> icon will appear at the top of the screen. To cancel the image protection, press <0>...
Page 281: K Recording And Playing Voice Memos
K Recording and Playing Voice Memos You can append a voice memo to a captured image. The voice memo will be saved as a WAV sound file with the same file number as the image. It can be played back with the camera or provided software. Recording a Voice Memo Select the image to which you want to append a voice memo.
Page 282: Playing A Voice Memo
K Recording and Playing Voice Memos Playing a Voice Memo When [85: J/K button function] is set to [Play memo (Hold: Rec. memo)] (p.338), you can play back a voice memo appended to an image. Set [85: J/K button function] to [Play memo (Hold: Rec.
Page 283: Copying Images
a Copying Images The images recorded on one card can be copied to the other card. 3 Copying Individual Images Select [Image copy]. Under the [31] tab, select [Image copy], then press <0>. Select [Sel.Image]. Check the copy source and target card’s capacity.
Page 284 a Copying Images Select the images to be copied. Total images selected Turn the <5> dial to select an image to be copied, then press <0>. The <X> icon will appear on the upper left of the screen. If you press the button and turn the <6>...
Page 285 a Copying Images Select [OK]. Check the copy source and target card’s information. Turn the <5> dial to select [OK], then press <0>. The copying will start and its progress will be displayed. When the copying is completed, the result will be displayed. Select [OK] to return to the screen in step 2.
Page 286: L Erasing Images
L Erasing Images You can either select and erase images one by one or erase them in one batch. Protected images (p.279) will not be erased. Once an image is erased, it cannot be recovered. Make sure you no longer need the image before erasing it. To prevent important images from being erased accidentally, protect them.
Page 287 L Erasing Images Select [Select and erase images]. Select [Select and erase images], then press <0>. The images will be displayed. If you press the button and turn the <6> dial counterclockwise, you can select an image from a three- image display.
Page 288: Changing Image Playback Settings
Changing Image Playback Settings 3 Adjusting the LCD Monitor Brightness You can adjust the brightness of the LCD monitor to make it easier to read. Select [LCD brightness]. Under the [52] tab, select [LCD brightness], then press <0>. Adjust the brightness. While referring to the gray chart, turn the <5>...
Page 289: Auto Rotation Of Vertical Images
Changing Image Playback Settings 3 Auto Rotation of Vertical Images Vertical images are rotated automatically so they are displayed vertically on the camera’s LCD monitor and on the personal computer instead of horizontally. You can change the setting for this feature.
Page 290 MEMO...
Page 291: Post-Processing Images
Post-Processing Images You can process RAW images with the camera or resize (shrink) JPEG images. The camera may not be able to process images taken with another camera. Post-processing images as described in this chapter is not possible if the camera is set for multiple exposures or while it is connected to a personal computer via the <C>...
Page 292: R Processing Raw Images With The Camera
R Processing RAW Images with the Camera You can process 1 images with the camera and save them as JPEG images. While the RAW image itself does not change, you can process the RAW image according to different conditions to create any number of JPEG images from it.
Page 293 R Processing RAW Images with the Camera Displaying the setting screen Press <0> to display the selected function’s setting screen. Turn the <5> or <6> dial to change the setting. To return to the screen in step 3, press <0>. Save the image.
Page 294 R Processing RAW Images with the Camera RAW Image Processing Options Brightness adjustment You can adjust the image brightness up to ±1 stop in 1/3-stop increments. The displayed image will reflect the setting’s effect. White balance (p.143) You can select the white balance. If you select [P], turn the <6> dial to set the color temperature on the setting screen.
Page 295 R Processing RAW Images with the Camera Color space (p.168) You can select either sRGB or Adobe RGB. Since the camera’s LCD monitor is not compatible with Adobe RGB, the image will not look very different when either color space is set. Peripheral illumination correction (p.157) If [Enable] is set, the corrected image will be displayed.
Page 296 R Processing RAW Images with the Camera Chromatic aberration correction When [Enable] is set, the lens’ chromatic aberrations (color fringing along the subject’s outline) can be corrected. If [Enable] is set, the corrected image will be displayed. If the effect is difficult to discern, press the ...
Page 297: S Resize
S Resize You can resize an image to make the pixel count lower and save it as a new image. Resizing an image is possible only with JPEG 3/H/5 images. JPEG 6 and RAW images cannot be resized. Select [Resize]. Under the [32] tab, select [Resize], then press <0>.
Page 298 S Resize Resize Options According to Original Image Size Available Resize Settings Original Image Size...
Page 299: Sensor Cleaning
If visible spots still remain after the automatic sensor cleaning, having the sensor cleaned by a Canon Service Center is recommended. Even while the Self Cleaning Sensor Unit is operating, you can press the shutter button halfway to interrupt the cleaning and start shooting immediately.
Page 300: Automatic Sensor Cleaning
f Automatic Sensor Cleaning Whenever you set the power switch to <1/R> or <2>, the Self Cleaning Sensor Unit operates to automatically shake off the dust on the front of the sensor. Normally, you need not pay attention to this operation.
Page 301: Appending Dust Delete Data
Appending Dust Delete Data Normally, the Self Cleaning Sensor Unit will eliminate most of the dust that may be visible on captured images. However, in case visible dust still remains, you can append the Dust Delete Data to the image for erasing the dust spots later.
Page 302 3 Appending Dust Delete Data Photograph a solid-white object. At a distance of 20 cm - 30 cm (0.7 ft. - 1.0 ft.), fill the viewfinder with a patternless, solid-white object and take a picture. The picture will be taken in aperture- priority AE mode at an aperture of f/22.
Page 303: Manual Sensor Cleaning
Before cleaning the sensor, detach the lens from the camera. The surface of the image sensor is extremely delicate. If the sensor needs to be cleaned directly, having it done by a Canon Service Center is recommended. Select [Sensor cleaning].
Page 304 If the battery level becomes low while you clean the sensor, the beeper will sound as a warning. Stop cleaning the sensor. If a smudge that cannot be removed with a blower remains, having the sensor cleaned by a Canon Service Center is recommended.
Page 305: Printing Images And Transferring Images To A Computer
Printing Images and Transferring Images to a Computer Printing (p.308) You can connect the camera directly to a printer and print out the images on the card. The camera is compatible with “wPictBridge” which is the standard for direct printing. Digital Print Order Format (DPOF) (p.315) DPOF (Digital Print Order Format) enables you to print images recorded on the card according to your printing...
Page 306: Preparing To Print
Preparing to Print The direct printing procedure can be performed entirely with the camera while you look at the LCD monitor. Connecting the Camera to a Printer Set the camera’s power switch to <2>. Set up the printer. For details, refer to the printer’s instruction manual.
Page 307 Preparing to Print Play back the image. PictBridge Press the < > button. The image will appear, and the <w> icon will appear on the upper left to indicate that the camera is connected to a printer. Movies cannot be printed. The camera cannot be used with printers compatible only with CP Direct or Bubble Jet Direct.
Page 308: Wprinting
wPrinting The screen display and setting options will differ depending on the printer. Some settings may not be available. For details, refer to the printer’s instruction manual. Printer-connected icon Select the image to be printed. Check that the <w> icon is displayed on the upper left of the LCD monitor.
Page 309 wPrinting Q Setting the Paper Size Select the size of the paper loaded in the printer, then press <0>. The paper type screen will appear. Y Setting the Paper Type Select the type of the paper loaded in the printer, then press <0>. The page layout screen will appear.
Page 310: Set The Printing Effects
wPrinting Set the printing effects. Set if necessary. If you do not need to set any printing effects, go to step 5. What is displayed on the screen differs depending on the printer. Select the option, then press <0>. Select the desired printing effect, then press <0>.
Page 311: Start Printing
wPrinting Set the date and file number imprinting. Set if necessary. Select < >, then press <0>. Set as desired, then press <0>. Set the number of copies. Set if necessary. Select < >, then press <0>. Set the number of copies, then press <0>.
Page 312 wPrinting e Adjustment of Printing Effects In step 4 on page 310, select the printing effect. When the <e> icon is highlighted next to <z>, you can press the button. You can then adjust the printing effects. What can be adjusted or what is displayed will depend on the selection made in step 4.
Page 313: Trimming The Image
wPrinting Trimming the Image You can crop the image and print only Tilt correction the trimmed portion as if the image was recomposed. Set the trimming right before printing. If you set the trimming and then set the print settings, you may have to set the trimming again before printing.
Page 314 wPrinting Depending on the printer, the trimmed image area may not be printed as you specified. The smaller you set the trimming frame, the grainier the picture will look in the print. While trimming the image, look at the camera’s LCD monitor. If you look at the image on a TV screen, the trimming frame may not be displayed accurately.
Page 315: W Digital Print Order Format (Dpof)
W Digital Print Order Format (DPOF) You can set the print type, date imprinting, and file number imprinting. The print settings will be applied to all print-ordered images. (Settings cannot be set individually for each image.) Setting the Printing Options Select [Print order].
Page 316 W Digital Print Order Format (DPOF) Standard Prints one image on one sheet. Index Multiple thumbnail images are printed on one sheet. Print type Both Prints both the standard and index prints. Date [On] imprints the recorded date on the print. File number [On] imprints the file number on the print.
Page 317: Print Ordering
W Digital Print Order Format (DPOF) Print Ordering Sel.Image Select and order images one by one. If you press the button and turn the <6> dial counterclockwise, you can select an image from a three-image display. To return to the single-image display, turn the <6>...
Page 318: W Direct Printing With Dpof
W Direct Printing with DPOF With a PictBridge printer, you can easily print images with DPOF. Prepare to print. See page 306. Follow the “Connecting the Camera to a Printer” procedure up to step 5. Under the [31] tab, select [Print order]. Select [Print].
Page 319: Transferring Images To A Personal Computer
d Transferring Images to a Personal Computer You can connect the camera to a personal computer and operate the camera to transfer images on the card to the personal computer. This is called direct image transfer. Direct image transfer is performed and controlled from the camera, with the interface displayed on the camera’s LCD monitor.
Page 320: Transferring Raw+Jpeg Images
d Transferring Images to a Personal Computer Set the camera’s power switch to <1>. When the personal computer prompts you to select a program, select [EOS Utility]. The EOS Utility screen will appear on the personal computer. After the EOS Utility screen appears, do not operate EOS Utility. If any screen other than EOS Utility’s top screen is displayed, [Direct transfer] in step 5 on page 322 will not be displayed.
Page 321 d Transferring Images to a Personal Computer 3 Select the Images to be Transferred Sel.Image Select [Image transfer]. Under the [32] tab, select [Image transfer], then press <0>. Select [Image sel./transfer]. Select [Image sel./transfer], then press <0>. Select [Sel.Image]. Select [Sel.Image], then press <0>. Select the images to be transferred.
Page 322 d Transferring Images to a Personal Computer Transfer the image. On the computer screen, check that EOS Utility’s top screen is displayed. Select [Direct transfer], then press <0>. On the confirmation screen, select [OK] and the images will be transferred to the personal computer. Images selected with [Sel.n] and [All image] can also be transferred this way.
Page 323: Customizing The Camera
Customizing the Camera You can customize various camera features to suit your picture-taking preferences with Custom Functions. Also, you can register the current camera settings under shooting modes <w1>, <w2>, or <w3>, or save the camera settings to a card.
Page 324: Custom Functions
Custom Functions k Movie 81: Exposure A LV Shooting Shooting Exposure level increments p.326 ISO speed setting increments Bracketing auto cancel (Still photo, with WB Bracketing sequence bracketing p.327 set) Number of bracketed shots Spot metering linked to AF point p.328 Safety shift p.329...
Page 325 3 Custom Functions k Movie A LV 84: Display/Operation Shooting Shooting Focusing Screen p.334 Viewfinder info. during exposure LCD panel illumination during Bulb p.335 Recording card, image size setting 85: Operation Dial direction during Tv/Av p.336 Av setting without lens Multi function lock p.337 Custom Controls...
Page 326: Custom Function Settings
Custom Function Settings Under the [8] tab, you can customize various camera features to suit your picture-taking preferences. Any settings different from the default will be displayed in blue. C.Fn1: Exposure Exposure level increments 1/3: 1/3-stop, Exposure compensation 1/3-stop Sets 1/3-stop increments for the shutter speed, aperture, exposure compensation, and flash exposure compensation.
Page 327 3 Custom Function Settings Bracketing sequence The AEB shooting sequence and white balance bracketing sequence can be changed. 0 - +: 0, -, + - 0+ : -, 0, + +0 - : +, 0, - White Balance Bracketing B/A Direction M/G Direction 0 : Standard exposure 0 : Standard white balance 0 : Standard white balance...
Page 328 3 Custom Function Settings Spot metering linked to AF point You can enable or disable AF point-linked spot metering in the <r> metering mode. Center AF point only Regardless of the AF point currently selected, spot metering will always be linked to the viewfinder’s center AF point. Linked to active AF point Spot metering will be linked to the manually-selected AF point.
Page 329 3 Custom Function Settings Safety shift OFF: Disable Tv/Av: Shutter speed/Aperture This function takes effect in the shutter-priority AE (s) and aperture- priority AE (f) modes. If the subject’s brightness changes and the standard exposure cannot be obtained within the autoexposure range, the camera will automatically change the manually-selected setting to obtain a standard exposure.
Page 330: C.fn2: Exposure
3 Custom Function Settings C.Fn2: Exposure Restrict shooting modes You can restrict the shooting modes selectable with the <W> button. Select a shooting mode (a/s/f/d/BULB/w1/w2/w3) to be made selectable and press <0> to append a checkmark <X>. The restricted shooting mode settings are not registered to C1, C2, or C3. At least one shooting mode must be checkmarked <X>.
Page 331 3 Custom Function Settings Set shutter speed range You can set the shutter speed range. In the <s> and <a> modes, you can set the shutter speed manually within the range that you have set. In the <d> and <f> modes, the shutter speed will be set automatically within the range that you have set.
Page 332 3 Custom Function Settings AE Microadjustment Normally, this adjustment is not required. Perform this adjustment only if necessary. Note that performing this adjustment may prevent the correct exposure from being achieved. You can fine-tune the standard for exposure metering. This adjustment can help if automatic exposure always makes the image look too dark or too bright even without any exposure compensation.
Page 333: C.fn3: Drive
3 Custom Function Settings C.Fn3: Drive Continuous shooting speed You can set the continuous shooting speed for <o> high-speed continuous shooting and low-speed continuous shooting. High speed You can set it from 2 to 12 shots/sec. Low speed You can set it from 1 to 11 shots/sec. If you set 12 or 11 shots/sec.
Page 334: C.fn4: Disp./Operation
3 Custom Function Settings C.Fn4: Display/Operation Focusing Screen You can change the focusing screen to an Ec-series focusing screen more suited for your shooting. If you change the focusing screen, change this setting to match the focusing screen type to obtain the correct exposure. Std.: Ec-CV Standard focusing screen.
Page 335: Lcd Panel Illumination During Bulb
3 Custom Function Settings When the shooting mode is set to “Bulb”, the viewfinder information will not be displayed even if [Enable] is set. LCD panel illumination during Bulb You can set the LCD panel illumination behavior during Bulb exposures, such as whether it stays on during the exposure, and whether it turns off or stays on when the ...
Page 336: C.fn5: Operation
3 Custom Function Settings C.Fn5: Operation Dial direction during Tv/Av Normal Reverse direction You can reverse the dial’s turning direction when setting the shutter speed and aperture. In the <a> shooting mode, the turning direction of the <6> and <5> dial will be reversed.
Page 337: Multi Function Lock
3 Custom Function Settings Multi function lock When the power switch is set to <R>, it will prevent the <6>, <5>, and <9> from accidentally changing a setting. Select the camera control(s) you want to lock when the power switch is set to <R>, then press <0>...
Page 338: J/K Button Function
3 Custom Function Settings J/K button function You can change the function of the <J/K> button. During image playback, you can protect images, record a voice memo, and rate images. J/K Protect (Hold: Record memo) To protect an image, press the <J/K> button. To start recording a voice memo, hold down the <J/K>...
Page 339: C.fn6: Others
3 Custom Function Settings C.Fn6: Others Add cropping information If you set cropping information, vertical lines for the aspect ratio you have set will appear on the Live View image. You can then compose the shot as if you were shooting with a medium- or large-format camera (6x6 cm, 4x5 inch, etc.).
Page 340: Shutter Release Time Lag
3 Custom Function Settings Shutter release time lag Normally, the shutter release is controlled for a stable release time lag. By setting [Shortened], this stabilization control can be omitted to make the shutter-release time lag shorter. Standard Shortened The normal shutter-release time lag is approx. 0.055 sec. when the aperture is stopped down by no more than four stops (depending on the lens).
Page 341: Same Exposure For New Aperture
3 Custom Function Settings Same exposure for new aperture If the <a> mode (manual exposure shooting) is set and the ISO speed is set manually (other than Auto ISO), the maximum aperture’s f/number may change to a high number (smaller aperture) or a low number if you perform any of the following: 1.
Page 342 3 Custom Function Settings This function does not work with macro lenses whose actual aperture f/number changes when the magnification changes. This function does not work with movies. If [Shutter speed] is set and the same exposure cannot be maintained within the shutter speed range set with the [82: Set shutter speed range], shutter speed will not be changed automatically.
Page 343: 85: Custom Controls
85: Custom Controls You can assign frequently-used functions to camera buttons or dials according to your preferences. Select [85: Custom Controls]. Under the [85] tab, select [Custom Controls], then press <0>. The Custom Controls screen will appear. Select a camera button or dial. Turn the <5>...
Page 344 85: Custom Controls Assignable Functions to Camera Controls Function Page Metering and AF start AF stop Switch to registered AF function ONE SHOT z AI SERVO Switch to registered AF point AF point direct selection Select AF point, + OzS during metering) Metering start AE lock...
Page 345 85: Custom Controls * The AF stop button ( ) is provided only on super telephoto IS lenses.
Page 346: Function Page
85: Custom Controls Function Page Image size selection One-touch image quality setting One-touch image quality (hold) Record func+card/folder selection 14fps super high speed Picture Style White balance selection Depth-of-field preview IS start VF electronic level Menu display Register/recall shooting function Start movie recording (when k set) Switch to Custom shooting mode Image replay...
Page 347 85: Custom Controls * The AF stop button ( ) is provided only on super telephoto IS lenses.
Page 348: Metering And Af Start 348 K K
85: Custom Controls : Metering and AF start When you press the button assigned to this function, metering and AF are executed. *1: If it is assigned to the or <A> button and you press the button in step 3 on page 343, you can set the AF in detail.
Page 349 85: Custom Controls AI Servo AF characteristics (p.85) Press the or <A> button to perform AF with [Case1] to [Case6]. AF mode (p.66) Press the or <A> button to perform AF with AF mode set. Super high speed continuous shooting (p.116) Press the ...
Page 350: Af Stop K K
85: Custom Controls : AF stop The AF will stop while you hold down the button assigned to this function. Convenient when you want to lock the focus during AI Servo : Switch to registered AF function After setting AF area selection mode (p.69), Tracking sensitivity (p.90), Acceleration/deceleration tracking (p.91), AF point auto switching (p.92), AI Servo 1st image priority (p.94), and AI Servo 2nd image priority (p.94) and assigning this function to a button, you can apply...
Page 351: Af Point Direct Selection
85: Custom Controls : AF point direct selection During metering, you can select an AF point directly with the <5> dial or <9> without pressing the <S> button. With the <5> dial, you can select a left or right AF point, or cycle through the zones if using Zone AF. *4: If you use <9>...
Page 352: During Metering)
85: Custom Controls : FE lock During flash photography, pressing the button assigned to this function will fire a preflash and record the required flash output (FE lock). : Set ISO speed You can press <0> to change the ISO speed. Set while looking at the top LCD panel, viewfinder, or LCD monitor.
Page 353: Aperture Setting In M Mode
85: Custom Controls : Aperture setting in M mode In manual exposure <a>, you can set the aperture with the <6> or <5> dial. : Exposure compensation (hold button, turn You can set exposure compensation by holding down <0> and turning the <6>...
Page 354 85: Custom Controls : Record func+card/folder selection Press <0> to display the [Record func+card/folder sel.] screen (p.120) on the LCD monitor. : 14fps super high speed In the <o> drive mode, while you hold down the or <A> button and press the shutter button completely, you can switch to super high speed continuous shooting (max.
Page 355 85: Custom Controls : VF electronic level When you press the button assigned to this function, the viewfinder will display a grid and an electronic level using the AF points. 1° Over 4° 1° Over 6° : Menu display Pressing <0> will display the menu on the LCD monitor. : Register/recall shooting function You can manually set the main shooting functions such as the shooting mode, ISO speed, metering mode, and AF Area selection mode and...
Page 356 85: Custom Controls : Start movie recording (when k set) With [LV z/k set.] set to [Movies], pressing the button assigned with this function will start the movie shooting immediately. To stop the movie shooting, press the button again. : Switch to Custom shooting mode When the shooting mode is not <w1>, <w2>, or <w3>, you can press the ...
Page 357: Registering My Menu
Registering My Menu Under the My Menu tab, you can register up to six menu options and Custom Functions whose settings you change frequently. Select [My Menu settings]. Under the [9] tab, select [My Menu settings], then press <0>. Select [Register to My Menu]. Select [Register to My Menu], then press <0>.
Page 358: Saving And Loading Camera Settings
Saving and Loading Camera Settings The camera’s shooting modes, menus, Custom Functions, and other camera settings can be saved to the card as a camera settings file. When this file is loaded by the camera, the saved camera settings will be applied.
Page 359 3 Saving and Loading Camera Settings Saved Settings Shooting functions Shooting mode, Shutter speed, Aperture, ISO speed, AF mode, AF area selection mode, AF point, Metering mode, Drive mode, Exposure compensation amount, Flash exposure compensation amount Menu functions [z1] White balance, Set Custom WB, White balance Shift/ Bracketing, Color space, Picture Style, Lens aberration correction (Peripheral illumination correction, Chromatic aberration correction), Multiple exposure (settings)
Page 360 3 Saving and Loading Camera Settings Loading Camera Settings In step 2, select [Load from card]. Up to ten camera settings files saved in the card will be displayed. When you select the desired file, it will be loaded and the settings will be applied to the camera. Compatibility of camera settings file A file saved by a camera having firmware version 2.x.x cannot be read by a camera having firmware version 1.x.x.
Page 361: W: Registering Custom Shooting Modes
w: Registering Custom Shooting Modes You can register your preferred shooting mode, menu settings, Custom Function settings, and other current camera settings to the <w1>/ <w2>/<w3> Custom shooting modes. To use <w2> or <w3>, set them in [82: Restrict shooting modes] (p.330). Select [Custom shooting mode (C1-C3)].
Page 362 w: Registering Custom Shooting Modes Settings Registered Shooting functions Shooting mode, Shutter speed, Aperture, ISO speed, AF mode, AF area selection mode, AF point, Metering mode, Drive mode, Exposure compensation amount, Flash exposure compensation amount Menu functions [z1] White balance, Set Custom WB, White balance Shift/ Bracketing, Color space, Picture Style, Lens aberration correction (Peripheral illumination correction, Chromatic aberration correction), Multiple exposure (settings)
Page 363 w: Registering Custom Shooting Modes My Menu settings will not be registered. When the shooting mode is <w1>, <w2>, or <w3>, you cannot select [54: Clear all camera settings] and [87: Clear all Custom Func. (C.Fn)]. Even in the <w1>, <w2>, or <w3> shooting mode, you can still change the shooting function settings and menu settings.
Page 364 MEMO...
Page 365: Reference
Reference This chapter provides reference information for camera features, system accessories, etc. Using the Cable Protector Interface cable Cable Protector HDMI cable (Sold separately)
Page 366: Function Availability Table According To Shooting Mode
Function Availability Table According to Shooting Mode o: Set automatically k: User selectable : Not selectable/Disabled Viewfinder Shooting k Movie z LV Function Shooting Shooting d s f a BULB k k k k All image quality settings selectable (Still photo) k k k k Automatically set/Auto ISO ISO speed...
Page 367 Function Availability Table According to Shooting Mode z LV k Movie Viewfinder Shooting Function Shooting Shooting d s f a BULB k k k k Auto AF point selection With f k k k k Manual k k k k AF-assist beam k k k k Manual focusing (MF)
Page 368: System Map
System Map ST-E2 ST-E3-RT 90EX 270EX II 320EX 430EX II 600EX-RT/ Macro Ring Lite Macro Twin Lite 600EX MR-14EX MT-24EX Bundled Accessories Dioptric Adjustment Lenses Eg Anti-Fog Eyepiece Eg Wide Strap Cable protector Eyecup Eg CR2025 lithium battery Angle Finder C EOS DIGITAL Software Instruction Hand Strap...
Page 369 System Map GPS Receiver Timer Remote Remote Wireless GP-E2 Controller Switch Controller TC-80N3 RS-80N3 LC-5 EF lenses External microphone HDMI Cable HTC-100 (2.9 m/9.5 ft.) Stereo AV Cable TV/Video AVC-DC400ST (1.3 m/4.3 ft.) Wireless File Transmitter WFT-E6 Interface Cable IFC-200U (1.9 m/6.2 ft.) Wireless LAN Interface Cable access point...
Page 370: B Button Functions
B Button Functions When you press the button while the camera is ready to shoot, you can display [Displays camera settings], [Electronic level] (p.61), and [Displays shooting functions] (p.371). Under the [52] tab, [z button display options] enables you to select the options displayed when the ...
Page 371: Shooting Settings
B Button Functions Shooting Settings White balance AE lock Highlight tone priority Aperture Exposure level indicator Picture Style ISO speed Shutter speed Exposure level indicator Shooting mode Auto Lighting Flash exposure compensation Optimizer AF mode Focus confirmation light Quick Control icon AF status indicator Battery check Possible shots...
Page 372: Checking The Battery Information
(Red): Purchasing a new battery is recommended. The use of a genuine Canon Battery Pack LP-E4N or LP-E4 is recommended. If you use any battery other than the Battery Pack LP-E4N or LP-E4, the camera’s full performance may not be attained or malfunction may result.
Page 373: Using A Household Power Outlet
Using a Household Power Outlet With the AC Adapter Kit ACK-E4 (sold separately), you can connect the camera to a household power outlet and not worry about the remaining battery level. Connect the DC Coupler’s plug. Connect the DC Coupler’s plug to the AC adapter’s DC terminal.
Page 374: Replacing The Date/Time Battery
Replacing the Date/Time Battery The date/time (backup) battery maintains the camera’s date and time. Its service life is approx. 5 years. If the date/time is reset when camera is turned on, follow the procedure below to replace the backup battery with a new CR2025 lithium battery.
Page 375: Menu Settings
Menu Settings For Viewfinder Shooting and Live View Shooting z: Shooting 1 (Red) Page Q / W / E / R / Y / U / D / O (1 - 5) White balance / P (Approx. 2500 - 10000) / PC-1 - 5 Set Custom WB Manual registration of white balance data White balance correction: B/A/M/G bias, 9...
Page 376 Menu Settings z: Shooting 2 (Red) Page Compression rate for 3 JPEG quality 1 / 41 / 61 Image type/size 3 / H / 5 / 6 ISO speed / ISO speed range / Auto ISO range ISO speed settings / Minimum shutter speed Disable / Low / Standard / High Auto Lighting...
Page 377 Menu Settings z: Shooting 4* (Red) Page LV z/k setting Disable / Stills / Movies Live mode / u Live mode / Quick mode AF mode Off / 3x3 l / 6x4 m / 3x3+diag n Grid display Enable / During e / Disable Exposure simulation Silent LV shooting Mode 1 / Mode 2 / Disable...
Page 378 Menu Settings 2: AF3 (Purple) Page Enable after One-Shot AF / Disable after One- USM lens electronic MF Shot AF / Disable in AF mode AF-assist beam firing Enable / Disable / IR AF assist beam only One-Shot AF release Release priority / Focus priority priority 2: AF4 (Purple)
Page 379 Menu Settings 2: AF5 (Purple) Page Manual AF point Stops at AF area edges / Continuous selection pattern Selected (constant) / All (constant) / Selected AF point display during (pre-AF, focused) / Selected (focused) / focus Disable display VF display illumination Auto / Enable / Disable AF status in viewfinder Show in field of view / Show outside view AF Microadjustment Disable / All by same amount / Adjust by lens...
Page 380 Menu Settings 3: Playback 3 (Blue) Page Highlight alert Disable / Enable AF point display Disable / Enable Off / 3x3 l / 6x4 m / 3x3+diag n Playback grid Histogram Brightness / RGB Movie play count* Rec time / Time code 1x (no magnification) / 2x (magnify from center) / 4x (magnify from center) / 8x (magnify Magnification (Approx.)
Page 381 Menu Settings 5: Set-up 2 (Yellow) Page 1 min. / 2 min. / 4 min. / 8 min. / 15 min. / Auto power off 30 min. / Disable LCD brightness Adjustable to one of seven brightness levels Date (year, month, day) / Time (hour, min., Date/Time/Zone sec.) / Daylight saving time / Time zone LanguageK...
Page 382 Menu Settings 5: Set-up 4 (Yellow) Page Save/load camera Save/load camera settings to/from the card settings on card Register current camera settings to the w1, Custom shooting mode w2, w3 shooting mode. (C1-C3) Clear all camera Resets the camera to the default settings settings Display copyright information / Enter author’s Copyright information...
Page 383 Menu Settings For Movie Shooting z: Shooting 4 (Movie) (Red) Page LV z/k setting Disable / Stills / Movies Live mode / u Live mode / Quick mode AF mode Off / 3x3 l / 6x4 m / 3x3+diag n Grid display 1920x1080 (6 / 5 / 4) (W / X) 1280x720 (8 / 7) (W / X)
Page 384: Troubleshooting Guide
Canon Service Center. Power-Related Problems The battery pack does not recharge. Do not recharge any battery pack other than a genuine Canon Battery Pack LP-E4N or LP-E4. The battery charger’s <CAL/CHARGE> lamp blinks in red, no Charge level lamp is lit, or all three Charge level lamps are blinking.
Page 385 Troubleshooting Guide The battery becomes exhausted quickly. Use a fully-charged battery pack (p.30). The battery performance may have degraded. See [53: Battery info.] to check the battery’s recharge performance level (p.372). If the battery performance is poor, replace the battery pack with a new one. The number of possible shots will decrease with any of the following operations: •...
Page 386 Troubleshooting Guide No images can be shot or recorded. Make sure the card is properly inserted (p.35). If the card is full, replace the card or delete unnecessary images to make room (p.35, 286). If you try to focus in the One-Shot AF mode while the focus confirmation light <o>...
Page 387 Troubleshooting Guide There are fewer AF points. Depending on the attached lens, the number of usable AF points and patterns will differ. The lenses are categorized into nine groups from A to I. Check which group your lens belongs to. Using a lens in Groups F to H will have fewer usable AF points (p.77).
Page 388 Troubleshooting Guide The maximum burst during continuous shooting is lower. If you shoot something that has fine detail (such as a field of grass), the file size will be larger and the actual maximum burst may be lower than the number mentioned on page 126. ISO 100 cannot be set/ISO speed expansion cannot be selected.
Page 389 Make sure the flash (or PC sync cord) is securely attached to the camera. If you use a non-Canon flash unit with Live View shooting, set [z4: Silent LV shoot.] to [Disable] (p.214). The flash always fires at full output.
Page 390 Troubleshooting Guide Flash exposure compensation cannot be set. If flash exposure compensation has already been set with the Speedlite, flash exposure compensation cannot be set with the camera. When the Speedlite’s flash exposure compensation is canceled (set to 0), flash exposure compensation can be set with the camera.
Page 391 Troubleshooting Guide The ISO speed cannot be set for movie shooting. If the shooting mode is <d/s/f/BULB>, the ISO speed will be set automatically. In the <a> mode, you can freely set the ISO speed (p.232). For movie shooting, ISO 32000/40000/51200 cannot be set. Under [z2: ISO speed settings], if [ISO speed range]’s [Maximum] is set to [51200/H] or higher, the manual setting range’s Maximum will be expanded to enable ISO 32000/40000/51200 to be set.
Page 392 Troubleshooting Guide The subject looks distorted during movie shooting. If you move the camera to the left or right quickly (high-speed panning) or shoot a moving subject, the image may look distorted. The image flickers or horizontal stripes appear during movie shooting.
Page 393 Troubleshooting Guide Operation Problems I cannot change the setting with <6>, <5>, or <9>. Set the power switch to <1> (p.38). Check the [85: Multi function lock] setting (p.337). Vertical-grip controls such as <6> and <9> do not work. Set the vertical-grip operation switch to <1> (p.49). The camera button/dial’s function has changed.
Page 394 Troubleshooting Guide The file numbering does not start from 0001. If the card already contains recorded images, the image number may not start from 0001 (p.164). The shooting date and time displayed is incorrect. Make sure the correct date and time has been set (p.40). Check the time zone and daylight savings time (p.41).
Page 395 Troubleshooting Guide Playback Problems Part of the image blinks in black. [33: Highlight alert] is set to [Enable] (p.255). A red box is displayed on the image. [33: AF point disp.] is set to [Enable] (p.255). The image cannot be erased. If the image is protected, it cannot be erased (p.279).
Page 396 Troubleshooting Guide No image appears on the TV screen. Use the stereo AV cable that came with the camera (p.278). Make sure the stereo AV cable or HDMI cable’s plug is inserted all the way in (p.275, 278). Set the video OUT system (NTSC/PAL) to the same video system as the TV set (p.278).
Page 397 Troubleshooting Guide Sensor Cleaning Problems The shutter makes a noise during sensor cleaning. If you selected [Clean nowf], the shutter will make a noise, but no picture is taken (p.300). Automatic sensor cleaning does not work. If you repeatedly turn the power switch <1> and <2> at a short interval, the <f>...
Page 398: System Status Display
You can also check the status log for past Error and Caution messages. Use this function to check the camera’s condition. If necessary, take the camera to your nearest Canon Service Center for maintenance to minimize camera problems in the future. Select [System status display].
Page 399 Battery Pack LP-E4N or LP- E4, there may be a problem with the camera. Consult your nearest Canon Service Center. Retry operation was The shutter- and mirror-cocking operation performed for the shutter was not completed normally.
Page 400 Cautions. If there are more than five entries, the oldest entries will be deleted automatically. The shutter release cycles are displayed in units of 1000. If there have been 1,000,000 or more shutter release cycles, 1,000,000 will be displayed. If the same Error or Caution occurs often, consult a Canon Service Center.
Page 401: Error Codes
50, 60, Operate the power switch, remove and install the battery pack 70, 80, again, or use a Canon lens (p.34, 38). * If the error still persists, write down the error number and contact your nearest Canon Service Center.
Page 402: Specifications
* Dual CF card slots Image sensor size: Approx. 36 x 24 mm Compatible lenses: Canon EF lenses (except EF-S and EF-M lenses) (35 mm- equivalent lens focal length will be as indicated on the lens) Lens mount: Canon EF mount •...
Page 403 Specifications Noise reduction: Applicable to long exposures and high ISO speed shots Automatic image brightness correction: Auto Lighting Optimizer Highlight tone priority: Provided Lens aberration correction: Peripheral illumination correction, Chromatic aberration correction • Viewfinder Type: Eye-level pentaprism Coverage: Vertical/Horizontal approx. 100% (with Eye point approx. 20 mm) Magnification: Approx.
Page 404 Specifications AI Servo AF characteristics:Tracking sensitivity, Acceleration/deceleration tracking, AF point auto switching AF fine adjustment: AF Microadjustment (All lenses by same amount or Adjust by lens) AF-assist beam: Emitted by the EOS-dedicated external Speedlite • Exposure Control Metering modes: Approx. 100,000-pixel RGB metering sensor and 252-zone TTL metering at max.
Page 405 RAW+JPEG Large: Approx. 17 shots (approx. 17 shots) * During high-speed continuous shooting * Figures are based on Canon’s testing standards (ISO 100 and Standard Picture Style) and an 8 GB card. * Figures in parentheses apply to an UDMA mode 7, 128 GB card based on Canon’s testing standards.
Page 406 Specifications • Movie Shooting Movie recording MPEG-4 AVC/H.264 compression: Variable (average) bit rate Audio recording format: Linear PCM Recording format: Recording size and frame rate: 1920x1080 (Full HD) : 30p/25p/24p 1280x720 (HD) : 60p/50p 640x480 (SD) : 30p/25p * 30p: 29.97 fps, 25p: 25.00 fps, 24p: 23.976 fps, 60p: 59.94 fps, 50p: 50.00 fps Compression method: ALL-I (I-only), IPB...
Page 407 Specifications Sound recording: Built-in monaural microphone, external stereo microphone terminal provided Sound recording level adjustable, wind filter provided Grid display: Three types Still photo shooting: Possible • LCD Monitor Type: TFT color, liquid-crystal monitor Monitor size and dots: Wide, 8.1 cm (3.2-in.) (3:2) with approx. 1.04 million dots Brightness adjustment: Manual (7 levels) Electronic level: Provided...
Page 408 Specifications • Direct Printing Compatible printers: PictBridge-compatible printers Printable images: JPEG and RAW images Print ordering: DPOF Version 1.1 compatible • Wired LAN Ethernet: 10BASE-T, 100BASE-TX, 1000BASE-T FTP transfer: Automatic transfer upon shooting, Image selection/ transfer, Transfer with SET button, Transfer with caption EOS Utility: EOS Utility’s remote control works with wired LAN WFT server:...
Page 409 Specifications • Power Battery: Battery Pack LP-E4N/LP-E4 (Quantity 1) * AC power can be supplied via AC Adapter Kit ACK-E4 Battery information: Remaining capacity, Shutter count, and Recharge performance displayed Battery life: With viewfinder shooting: (Based on CIPA Approx. 1120 shots at 23°C/73°F, approx. 860 shots at 0°C/32°F testing standards) With Live View shooting: Approx.
Page 410 Specifications All the data above is based on Canon’s testing standards and CIPA (Camera & Imaging Products Association) testing standards and guidelines. Dimensions, maximum diameter, length and weight listed above are based on CIPA Guidelines (except weight for camera body only).
Page 411 Trademarks Adobe is a trademark of Adobe Systems Incorporated. Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. Macintosh and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries.
Page 412 Use of genuine Canon accessories is recommended This product is designed to achieve excellent performance when used with genuine Canon accessories. Canon shall not be liable for any damage to this product and/or accidents such as fire, etc., caused by the malfunction of non- genuine Canon accessories (e.g., a leakage and/or explosion of a battery...
Page 413: Safety Warnings
Safety Warnings Follow these safeguards and use the equipment properly to prevent injury, death, and material damage. Preventing Serious Injury or Death • To prevent fire, excessive heat, chemical leakage, and explosions, follow the safeguards below: - Do not use any batteries, power sources, and accessories not specified in this booklet.
Page 414 • Do not use paint thinner, benzene, or other organic solvents to clean the equipment. Doing so may cause fire or a health hazard. If the product does not work properly or requires repair, contact your dealer or your nearest Canon Service Center.
Page 415 If such changes or modifications should be made, you could be required to stop operation of the equipment. Canon U.S.A. Inc. One Canon Park, Melville, NY 11747, U.S.A. Tel No. 1-800-OK-CANON (1-800-652-2666) CAN ICES-3 (B) / NMB-3 (B)
Page 416 4. Do not expose the charger to rain or snow. 5. Use of an attachment not recommended or sold by Canon may result in fire, electric shock, or personal injury. 6. To reduce risk of damage to electric plug and cord, pull by plug rather than by cord when disconnecting charger.
Page 417 MEMO...
Page 418 MEMO...
Page 419 MEMO...
Page 420 MEMO...
Page 421 MEMO...
Page 422 MEMO...
Page 423 MEMO...
Page 424 MEMO...
Page 425: Software Start Guide
Software Start Guide This chapter gives an overview of the software in the EOS DIGITAL Solution Disk (CD-ROM) provided with the camera and explains how to install the software on a personal computer. It also explains how to view the PDF files on the Software Instruction Manual CD-ROM.
Page 426: Software Start Guide
Software Start Guide EOS DIGITAL Solution Disk This disk contains various software for EOS DIGITAL cameras. EOS Utility With the camera connected to a personal computer, EOS Utility enables you to transfer still photos and movies shot with the camera to the computer.
Page 427: Installing The Software
Insert EOS DIGITAL Solution Disk (CD-ROM). For Macintosh, double-click to open the CD-ROM icon displayed on the desktop, then double-click on [Canon EOS Digital Installer]. Click [Easy Installation] and follow the on-screen instructions to install.
Page 428 Software Start Guide Software Instruction Manual Contains the Software Instruction Manuals. Copying and Viewing the Instruction Manual PDFs Insert the [Software INSTRUCTION MANUAL] CD-ROM into your computer. Double-click the CD-ROM icon. For Windows, the icon is displayed in [(My) Computer]. For Macintosh, the icon is displayed on the desktop.
Page 429: Index
Index Numerics AF-ON (AF start) button ....46 AI SERVO (AI Servo AF)....68 10-sec. or 2-sec. delay....117 Accel./decel. tracking ....91 1280x720 ........239 AF pt auto switching....92 1920x1080 ........239 AF starting point....... 103 4- or 9-image index display...257 Illumination.......
Page 430 Index Calibration........32 Camera Date/Time........40 Camera shake ......193 Date/time battery Clear camera settings ....58 replacement ......374 Holding the camera ....45 Daylight saving time ....... 41 Save/load camera settings ..358 DC coupler ........373 Settings display ......370 Depth-of-field preview .. 176, 207, 210 System status......398 Dial Camera shake ......45, 46...
Page 431 Index FE lock ..........196 Grid display ....61, 212, 247 FE Microadjustment ......332 Feature guide........63 HD ........239, 275 File name ......162, 164 HDMI ........266, 275 File size....126, 240, 254, 255 HDMI CEC........276 Filter effect ........140 High ISO speed NR...... 153 Final image simulation ..210, 235 High-Definition (HD) ..
Page 432 Index Slide show ........272 Lens ..........43 Transfer ........319 Chromatic aberration View on TV .......266, 275 correction ......... 158 Voice memo......281 Lock release ......44 Peripheral illumination Image dust prevention ....299 correction ......... 157 Image review ........57 Live View shooting ....... 205 Image-recording quality Exposure simulation ....
Page 433 Aperture-priority AE ....229 Long exposures ....... 154 Autoexposure shooting.....227 Compression method ....239 Nomenclature ......... 18 Drop frame........246 Non-Canon flash units....197 Edit ...........270 NTSC........239, 381 Editing out first and last Number of AF points ...... 77 scenes ........270 Enjoying........266 External microphone....243...
Page 434 Index PictBridge ........305 RAW+JPEG ......... 123 Picture Style....135, 138, 141 Rear LCD panel ......26 Pixels ..........124 Rec. separately ......121 Playback ........251 Rec. to multiple ......121 Possible shots....39, 126, 208 Recharge........30 Power Record function ......120 Auto power off ......57 Recording level ......
Page 435 Index Shooting settings display ..50, 371 Tripod socket ........18 Shutter button .........46 Tv (Shutter-priority AE)..173, 228 Shutter synchronization ....202 Shutter-priority AE....173, 228 Ultra DMA (UDMA)......36 Silent shooting USB (Digital) terminal... 306, 319 Silent LV shooting.....214, 248 Single silent shooting....116 Vertical-grip ON/OFF switch...
Page 436 The lenses and accessories mentioned in this Instruction Manual are current as of November 2013. For information on the camera’s compatibility with any lenses and accessories introduced after this date, contact any Canon Service Center. CPH-E111-000 © CANON INC. 2013...

Canon EOS-1DX Instruction Manual

Table of Contents

Introduction

Getting Started

Setting the AF and Drive Modes

Image Settings

Exposure Control

Flash Photography

Shooting with the LCD Monitor

(Live View Shooting)

Shooting with the LCD Monitor (Live View Shooting)

Shooting Movies

Image Playback

Post-Processing Images

Sensor Cleaning

Printing Images and Transferring Images to a Computer

Customizing the Camera

84: Display/Operation

Assignable Functions to Camera Controls

Reference

Software Start Guide

Quick Links

Chapters

Related Manuals for Canon EOS-1DX

Summary of Contents for Canon EOS-1DX