Table of Contents
Advertisement
MICRO COMPONENT SYSTEM
DVD-E600MK2
The RDX-E600MK2 consists of the RX-E600MK2 and the DVD-E600MK2.
This service manual is for the DVD-E600MK2.
For the RX-E600MK2 service manual, please refer to the following publication number:
This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.
It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already
known and understood by the users, and have therefore not been restated.
WARNING:
IMPORTANT:
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and
service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable
and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please
contact the distributor's Service Division.
WARNING:
IMPORTANT:
I CONTENTS
TO SERVICE PERSONNEL ....................................... 2~5
LOCALE MANAGEMENT INFORMATION .................... 5
FRONT PANEL ............................................................... 6
REAR PANEL ................................................................. 6
REMOTE CONTROL PANEL ......................................... 6
SPECIFICATIONS ....................................................... 6~7
INTERNAL VIEW ............................................................ 7
DISASSEMBLY PROCEDURES .............................. 8~10
1 0 0 9 8 4
SERVICE MANUAL
RX-E600MK2 100983
IMPORTANT NOTICE
Failure to follow appropriate service and safety procedures when servicing this product may result in personal
injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons,
we advise all YAMAHA product owners that any service required should be performed by an authorized
YAMAHA Retailer or the appointed service representative.
The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or
recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.
Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).
Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.
MAINTENANCE FLOW CHART ............................. 11~15
IC DATA .................................................................. 16~17
DISPLAY DATA ............................................................ 18
BLOCK DIAGRAM ........................................................ 19
PRINTED CIRCUIT BOARD ................................... 20~24
SCHEMATIC DIAGRAM ......................................... 25~27
PIN CONNECTION DIAGRAM ..................................... 29
PARTS LIST ............................................................ 30~33
2005
All rights reserved.
This manual is copyrighted by YAMAHA and may not be copied or
redistributed either in print or electronically without permission.
RDX-E600MK2
DVD PLAYER
P.O.Box 1, Hamamatsu, Japan
'05.10
Advertisement
Table of Contents
Related Manuals for Yamaha RDX-E600MK2
Summary of Contents for Yamaha RDX-E600MK2
-
Page 1: Table Of Contents
This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already known and understood by the users, and have therefore not been restated. -
Page 2: To Service Personnel
DVD-E600MK2 I TO SERVICE PERSONNEL AC LEAKAGE WALL EQUIPMENT TESTER OR 1. Critical Components Information OUTLET UNDER TEST EQUIVALENT Components having special characteristics are marked s and must be replaced with parts having specifications equal to those originally installed. 2. Leakage Current Measurement (For 120V Models Only) When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated INSULATING... - Page 3 DVD-E600MK2 WARNING: Laser Safety This product contains a laser beam component. This component may emit invisible, as well as visible radiation, which may cause eye damage. To protect your eyes and skin from laser radiation, the following precautions must be used during servicing of the unit.
- Page 4 DVD-E600MK2 WARNING CAUTION The unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit Use of controls or adjustments or performance of itself is turned off. This state is called the standby mode. In procedures other than those specified herein may result in this state, this unit is designed to consume a very small hazardous radiation exposure.
-
Page 5: Prevention Of Electrostatic Discharge
DVD-E600MK2 Warning for power supply The primary side of the power supply carries live mains voltage when the player is connected to the mains even when the player is switched off ! This primary area is not shielded so it is possible to touch copper tracks and/or components when servicing the player. Service personnel have to take precautions to prevent touching this area or components in this area . -
Page 6: Front Panel
DVD-E600MK2 I FRONT PANEL I REMOTE CONTROL PANEL B, G, E models B, G, E models B, G, E models I REAR PANEL B, G, E models B, G, E models I SPECIFICATIONS PLAYBACK SYSTEM AUDIO PERFORMANCE DVD Video DA Converter 24 bits Video CD &... -
Page 7: Internal View
DVD-E600MK2 GENERAL DIMENSIONS Dimensions (W x H x D) 217 x 108 x 346 (8-9/16" x 4-1/4" x 13-5/8") Weight Approx. 2.6 Kg (5 lbs. 12 oz.) Finish Gold color G, E models Silver color B, G, E models Power Supply AC230V, 50Hz Power Consumption Standby Power Consumption (reference data) -
Page 8: Disassembly Procedures
DVD-E600MK2 I DISASSEMBLY PROCEDURES (Remove parts in the order as numbered.) Disconnect the power cable from the AC outlet. 1. Removal of Top Cover Top Cover a. Remove 4 screws (1), 4 screws (2). (Fig. 1) b. Slide the Top Cover rearward to remove it. Fig. - Page 9 DVD-E600MK2 MAIN (2) P.C.B. MAIN (3) P.C.B. CB301 CB205 MAIN (4) P.C.B. CB201 1106 1105 1301 1104 MONO BOARD 1103 CB17 1102 CB16 Fig. 3 6. Removal of MONO BOARD 4. Removal of MAIN (3) P.C.B. a. Remove 4 screws (8). (Fig. 3) a.
- Page 10 DVD-E600MK2 7. Removal of MAIN (5), MAIN (6) P.C.B. and POWER SUPPLY UNIT a. Remove 5 screws (9). (Fig. 4) b. Remove 5 screws (0). (Fig. 5) c. Remove 2 screws (A). (Fig. 5) d. Loosen 1 Locking Card Spacer. (Fig. 5) e.
-
Page 11: Maintenance Flow Chart
DVD-E600MK2 I MAINTENANCE FLOW CHART Start Power on Are voltages 1. Check Cable 2. Replace power supply unit if MAIN (5) Board is not shorted, at all pins of W4 in MAIN (5) Board otherwise find out first where the short is. normal ? Are voltages at +8V and +1V8 of power part... - Page 12 DVD-E600MK2 Check 74HCU04 (Ref 7103) and Is logo displayed Main Clock peripheral circuit. on TV screen? normal ? Check NCP303 (Ref 7102) and reset signal peripheral circuit. normal ? Is signal Check peripheral circuit of FLASH (Ref 7303) on FLASH (Ref 7303) normal ? Is signal on DRAM (Ref 7302)
- Page 13 DVD-E600MK2 Is signal Does sled automatically move to inside STBY (Pin 1 of MM1646) Check the STBY circuit when it is outside ? high level ? Is signal FMO Check the FMO circuit (Pin 5 of MM1646) more than 1.4V ? Are signals SL+ Check MM1646 and (Pin 11 of MM1646) &...
- Page 14 DVD-E600MK2 Is any signal Check circuit between Optical on pins A B C D E F of Is Focus on OK ? Pick Up and MT1389 MT1389 turned ON ? Check MT1389 and its peripheral circuit. Is DMO Check MT1389 and its Is Spindle on OK ? (pin 37 of MT1389) peripheral circuit.
- Page 15 DVD-E600MK2 Does AK4385ET Check connection between Is audio signal normal ? MT1389 and AK4385ET receive correct data ? Check AK4385ET and its Is output signal peripheral circuit correct ? Check circuit of filter, amplifier, and mute etc. Do GP1UM271 Check connection between Are GP1UM271, and uPD16312 communicate MT1389 and uPD16312 and...
-
Page 16: Ic Data
DVD-E600MK2 I IC DATA IC501: µPD16312GB-3B4 [MAIN (1) P.C.B.] 8-bit Microprocessor Grid Grid /Grid /Grid /Grid /Grid /Grid Command decoder Dimming circuit 16-bit Seg- Display memory output ment Serial I/F 16 bits x 11 words latch driver /Grid Timing generator key scan Data selector /Grid... - Page 17 DVD-E600MK2 IC501: µPD16312GB-3B4 [MAIN (1) P.C.B.] 8-bit Microprocessor Name Symbol Description Switch input These pins constitute a 4-bit general-purpose input port. Data output DOUT Output serial data at the falling edge of the shift clock, starting from low order bit. This is N-ch open-drain output pin. Data input Input serial data at rising edge of shift clock, starting from the low order bit.
-
Page 18: Display Data
DVD-E600MK2 I DISPLAY DATA G V1 : 7-BT-299GNK (WD602800) PATTERN AREA G PIN CONNECTION PIN NO. CONNECTION F2 NOTE : 1) F1, F2 ..Filament 2) NP ..No pin 3) 1G ~ 7G ..Grid G GRIG ASSIGNMENT G ANODE CONNECTION... -
Page 19: Block Diagram
DVD-E600MK2 I BLOCK DIAGRAM MAIN (1) MAIN (5) U501 • See page 27 → SCHEMATIC DIAGRAM • See page 27 → SCHEMATIC DIAGRAM GP1UM271 IR REMOTE • See page 27 → STANDBY/ON SCHEMATIC DIAGRAM SW501 W502 CB11 MAIN (3) CB17 KEY SW 502-506 JK301 IC501... -
Page 20: Printed Circuit Board
DVD-E600MK2 I PRINTED CIRCUIT BOARD (Foil side) MAIN (1) P.C.B. (Side A) MAIN (2) P.C.B. (Side A) MAIN (5) (CB16) MAIN (4) (CB204) STANDBY FL DISPLAY (SCART) MAIN (5) (CB17) MAIN (4) P.C.B. (Side A) LINE_R AGND LINE_L AGND BLANK MUTE MAIN (3) P.C.B. - Page 21 DVD-E600MK2 I PRINTED CIRCUIT BOARD (Foil side) MAIN (1) P.C.B. (Side B) Lead Free Solder Used MAIN (2) P.C.B. (Side B) Lead Free Solder Used 11 12 MAIN (4) P.C.B. (Side B) Lead Free Solder Used • Semiconductor Location Ref no. Location MAIN (3) P.C.B.
- Page 22 DVD-E600MK2 I PRINTED CIRCUIT BOARD (Foil side) MAIN (6) P.C.B. (Side A) MAIN (5) P.C.B. (Side A) to POWER SUPPLY UNIT (CN101, CN202) MAIN (1) MAIN (1) MAIN (6) (W502) (W501) (W5) MAIN (5) LOAD- (CB6) LOAD+ MONO BOARD TROUT MONO BOARD (1103) LOAD-...
- Page 23 DVD-E600MK2 I PRINTED CIRCUIT BOARD (Foil side) MAIN (5) P.C.B. (Side B) Lead Free Solder Used MAIN (6) P.C.B. (Side B) Lead Free Solder Used • Semiconductor Location Ref no. Location Ref no. Location D501 Q501 Q504 MAIN (7) P.C.B. (Side B) Lead Free Solder Used...
- Page 24 DVD-E600MK2 The first digit of a component indicates the component type. 1xxx : Connector 3xxx : Resistor 5xxx : Coil 7xxx : IC, Transistor, FET I PRINTED CIRCUIT BOARD (Foil side) 2xxx : Capacitor 4xxx : SMD jumper 6xxx : Diode 9xxx : Wire jumper FOR INFORMATION ONLY (NO REPLACEMENT COMPONENT PARTS WILL BE AVAILABLE) MONO Board-Top View...
- Page 25 DVD-E600MK2 The first digit of a component indicates the component type. 1xxx : Connector 3xxx : Resistor 5xxx : Coil 7xxx : IC, Transistor, FET I SCHEMATIC DIAGRAM 2xxx : Capacitor 4xxx : SMD jumper 6xxx : Diode 9xxx : Wire jumper FOR INFORMATION ONLY (NO REPLACEMENT COMPONENT PARTS WILL BE AVAILABLE) MONO BOARD 1/2 +3V3...
- Page 26 DVD-E600MK2 The first digit of a component indicates the component type. 1xxx : Connector 3xxx : Resistor 5xxx : Coil 7xxx : IC, Transistor, FET I SCHEMATIC DIAGRAM 2xxx : Capacitor 4xxx : SMD jumper 6xxx : Diode 9xxx : Wire jumper FOR INFORMATION ONLY (NO REPLACEMENT COMPONENT PARTS WILL BE AVAILABLE) 1301 E12 2301 A3...
- Page 27 DVD-E600MK2 SCHEMATIC DIAGRAM (MAIN) FL DISPLAY MAIN (7) -17.8 -17.8 -17.8 -20.9 MAIN (6) IR REMOTE STANDBY/ TO 1106 OF MONO BOARD Page 25 -14.3 TO 1105 OF MONO BOARD Page 25 KEY SW MAIN (1) MAIN (5) MAIN (3) 11.4 -18.9 AUDIO...
-
Page 28: Pin Connection Diagram
DVD-E600MK2 I PIN CONNECTION DIAGRAM PQ070X25MZP AK4385ET NJM78M05DL 1A NJM2068MD TK15420M ADG733 NJM78M08A 8V HD74HC126FP uPD16312GB Transistors 2SA1037K (Q, R, S) 2SA1708 (S, T) 2SC2412K (Q, R, S) 2SC4488 (S, T) 2SD1938F (S, T) DTC144EKA RSR025N03 Diodes UDZ5.1B 5.1V KDS160-RTK UDZS5.6BTE-17 5.6V Anode Anode... -
Page 29: Parts List
DVD-E600MK2 PARTS LIST I ELECTRICAL PARTS I WARNING Components having special characteristics are marked s and must be replaced with parts having specifications equal to those originally installed. ABBREVIATIONS IN THIS LIST ARE AS FOLLOWS: C.A.EL.CHP : CHIP ALUMI.ELECTROLYTIC CAP L.EMIT : LIGHT EMITTING MODULE C.CE... - Page 30 DVD-E600MK2 P.C.B. MAIN P.C.B. MAIN P.C.B. MAIN Chip Resistors The chip resistor is not supplied as a replacement part. Ref. No. Part No. Description Markets Ref. No. Part No. Description Markets Ref. No. Part No. Description Markets * When a chip resistor is necessary, use the following part. AAX60720: CHIP RESISTOR SAMPLE BOOK Ref.
- Page 31 DVD-E600MK2 I EXPLODED VIEW 1-1 (3) 1-1 (2) 1-1 (4) 1-1 (5) 1-1 (7) 1-111 1-103 SHEET/FL 1-110 1-1 (6) 1-101 1-102 1-111 1-110 1-104 1-103 %: Note on the MAIN P.C.B. Of the MAIN P.C.B. part Nos., only the silver (SI) type part Nos. are included in the table. The only different part between the gold (GD) and silver (SI) type parts is the sheet/FL that is attached to the fluorescent character display tube.
- Page 32 DVD-E600MK2 I MECHANICAL PARTS ✻ New Parts ✻ New Parts...
- Page 33 DVD-E600MK2...