Related Manuals for Fujitsu ADA-91270-90340-100PFV V1.0
Summary of Contents for Fujitsu ADA-91270-90340-100PFV V1.0
- Page 1 Fujitsu Microelectronics Europe FMEMCU-UG-910012-16 User Guide F²MC-16LX FAMILY EVALUATION BOARD ADA-91270-90340-100PFV V1.0 USER GUIDE...
-
Page 2: Revision History
V1.2, HWe: Chapter 9 (Related Products): socket corrected 2006-07-03 V1.3, MWi: MB96(F)34x added 2006-10-18 V1.4, HWe: Chapter 5 (Programming) corrected 2007-03-02 V1.5 Recycling Note added 2008-09-16 V1.6, MSc China-RoHS regulation added This document contains 24 pages. UG-910012-16 - 2 - © Fujitsu Microelectronics Europe GmbH... -
Page 3: Warranty And Disclaimer
Product or parts thereof, if the Product is returned to Fujitsu Microelectronics Europe GmbH in original packing and without further defects resulting from the customer’s use or the transport. -
Page 4: Table Of Contents
Edge connector (X3, X4) ..................16 7 BOARD MODIFICATION FOR MB96340 SERIES............17 8 SILK-PLOT OF THE BOARD ..................18 9 NOTES ON USING THE ADA-91270-90340-100PFV V1.0..........19 Stand-alone mode ....................19 PCB History......................19 10 RELATED PRODUCTS ....................20 11 INFORMATION IN THE WWW.................. -
Page 5: Overview
The adapter board will be delivered with the MB91F272WPFV (dual clock version). This microcontroller contains a 'burn-in'-boot loader for programming the flash. This board must only be used for test applications in an evaluation laboratory environment. © Fujitsu Microelectronics Europe GmbH - 5 - UG-910012-16... -
Page 6: Installation
Jumper 2 pol Open JP71 Optional: URXD Jumper 2 pol Open JP72 Optional: URST Jumper 2 pol Open JP73 Optional: RTS-CTS Jumper 2 pol Open JP74 Optional: URST Jumper 3 pol Open UG-910012-16 - 6 - © Fujitsu Microelectronics Europe GmbH... -
Page 7: Mb91270 Series
Jumper 2 pol Open JP71 Optional: URXD Jumper 2 pol Open JP72 Optional: URST Jumper 2 pol Open JP73 Optional: RTS-CTS Jumper 2 pol Open JP74 Optional: URST Jumper 3 pol Open © Fujitsu Microelectronics Europe GmbH - 7 - UG-910012-16... -
Page 8: Jumper Settings Of Flash-Can-100P-340
GH22 JP41 P00/P65 Jumper 3 pol JP42 P01/P66 Jumper 3 pol JP43a SCK0(MB90340) Jumper 2 pol Closed JP43b SCK0(MB90800) / SCK4(MB90945) Jumper 2 pol Open JP44 SIN_A Jumper 2 pol Closed UG-910012-16 - 8 - © Fujitsu Microelectronics Europe GmbH... - Page 9 ADA-91270-90340-100PFV v1.0 Chapter 3 Installation (LIN- (LIN- UART3) UART1) Please see the user guide ug-900003 for a detailed description of the FLASH-CAN100P-340 evaluation board. © Fujitsu Microelectronics Europe GmbH - 9 - UG-910012-16...
-
Page 10: Jumpers And Switches
Note: Dip-Switch S2 JP50: 1-2 MB90340 / MB96340 JP51: 1-2 RUN mode 4.1.2 MB91270 Series MD0 MD1 MD2 nc P11 P10 Note: Dip-Switch S2 JP50: 2-3 MB91270 RUN mode JP51: 2-3 UG-910012-16 - 10 - © Fujitsu Microelectronics Europe GmbH... -
Page 11: Analogue Power Supply Voltage (Jp: 60, 61, 62, 63)
If JP63 is open, the resistors R11 and R23 define AVRH. If JP62 is open, the resistors R26 and R27 define AVRL. By default the resistor network (R11, R23 and R26, R27) is not mounted on the board. © Fujitsu Microelectronics Europe GmbH - 11 - UG-910012-16... -
Page 12: Subclock (Jp: 55,56)
Pin 12 is connected to the 32kHz Subclock (X1A) JP56 (X1A/P41) Pin 12 is used as P41 and is connected to X3-12 Default: JP55: 1-4, JP56: 1-2 By default, the 32kHz-subclock-crystal is connected to the microcontroller. UG-910012-16 - 12 - © Fujitsu Microelectronics Europe GmbH... -
Page 13: Uart"A" (Jp: 52, 53, 54)
By default, UART1 is used as UART”A”. Note for MB91270 Series: Make sure that jumper JP21a and JP22a (LIN transceiver) on the FLASH-CAN-100P-340 are open, while the UART1 of MB91270 Series is used. © Fujitsu Microelectronics Europe GmbH - 13 - UG-910012-16... -
Page 14: Programming The Internal Flash
5.1 Asynchronous Mode The Flash-microcontroller of MB90340, MB96340, and MB91270 Series can be programmed in circuit by using the freeware “Fujitsu Flash MCU Programmer” that is available on the Fujitsu Micros CD-ROM or Web Site (http://www.fme.gsdc.de/gsdc.htm: select < Software <... - Page 15 6. Check that the Reset LED is off. Otherwise change the DTR polarity (JP35) and check the power supply voltage. 7. Start the tool “Fujitsu Flash MCU Programmer” software and follow the instructions: Note: The screenshot may differ regarding the used release version of the tool...
-
Page 16: Connectors
The following pins are not routed to the connecter (X3, X4): Pin 13 (VCC) Pin 14 (GND) Pin 42 (GND) Pin 63 (VCC) Pin 64 (GND) Pin 88 (VCC) Pin 89 (GND) Pin 90 (X1) Pin 91 (X0) UG-910012-16 - 16 - © Fujitsu Microelectronics Europe GmbH... -
Page 17: Board Modification For Mb96340 Series
Please see the following photograph of the backside of the board for a possible connection: The positive pole of the capacitor is connected to the middle pin of jumper JP57. The negative pole is connected to a ground pin of connector X14. © Fujitsu Microelectronics Europe GmbH - 17 - UG-910012-16... -
Page 18: Silk-Plot Of The Board
ADA-91270-90340-100PFV v1.0 Chapter 8 Silk-Plot of the Board 8 Silk-Plot of the Board VG96-male FlashKit Power- MAX232 Jack MAX232 CAN”B” UART”B” optional: LCD User-LEDs (P00-P07) Reset CAN”A” UART”A” LIN”A” LIN”B” UG-910012-16 - 18 - © Fujitsu Microelectronics Europe GmbH... -
Page 19: Notes On Using The Ada-91270-90340-100Pfv V1.0
ADA-91270-90340-100PFV v1.0 Chapter 9 Notes on using the ADA-91270-90340-100PFV V1.0 9 Notes on using the ADA-91270-90340-100PFV V1.0 9.1 Stand-alone mode The MB91F272 does not have an internal power-on reset circuitry. Therefore, when using the MB91F272 on the ADA-91270-90340-100PFV in stand-alone mode, a reset must be generated externally after powering-up the board. -
Page 20: Related Products
< MB2198-01 Emulator debugger main unit < MB2198-10 Emulator DSU cable < MB2198-130 Emulation POD < MB91V280CR-ES Evaluation chip for MB91270 Series, single-clock < MB2198-129 Emulator probe cable for MB91270/M05 Package UG-910012-16 - 20 - © Fujitsu Microelectronics Europe GmbH... -
Page 21: Information In The Www
Datasheets and Hardware Manuals, Support Tools (Hard- and Software) http://www.fme.gsdc.de/gsdc.htm Linear Products: Power Management, A/D and D/A Converters http://www.fujitsu.com/emea/services/microelectronics/linears/ Media Products: SAW filters, acoustic resonators and VCOs http://www.fujitsu.com/emea/services/microelectronics/saw/ For more information about FUJITSU MICROELECTRONICS http://www.fujitsu.com/emea/services/microelectronics/ © Fujitsu Microelectronics Europe GmbH - 21 - UG-910012-16... -
Page 22: China-Rohs Regulation
“Year”. UG-910012-16 - 22 - © Fujitsu Microelectronics Europe GmbH... - Page 23 X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/T11363-2006. • Data listed in the table represents best information available at the time of publication © Fujitsu Microelectronics Europe GmbH - 23 - UG-910012-16...
-
Page 24: Recycling
According to the European WEEE-Directive and its implementation into national laws we take this device back. For disposal please send the device to the following address: Fujitsu Microelectronics Europe GmbH Warehouse/Disposal Monzastraße 4a 63225 Langen UG-910012-16 - 24 - © Fujitsu Microelectronics Europe GmbH...