Advertisement
INTRODUCTION
The 5883 RF Transceiver Module:
N
contains an RF receiver and a transmitter,
N
is intended for use with 5800 series RF transmitters, including bi-
directional wireless units (e.g. 5804BD), and the 5800RL Wireless
Relay Module (see Fig. 1),
N
receives
alarm,
status,
transmitters, and passes these messages to the control panel via
wired connections, which then responds accordingly (arm/disarm the
system, initiate an alarm, etc.),
N
transmits system status and other conditions to bi-directional
devices (e.g., 5804BD),
N
emulates the functions of a 5800TM module, and can control the
relays on the 5800RL Wireless Relay Module,
N
features a Spatial Diversity system that virtually eliminates the
possibility of "Nulls" and "Dead Spots" within the coverage area,
N
incorporates new high-security encryption technology (UL-864 and
RF Jam Detect),
N
supports the number of zones shown in the chart at right.
MOUNT THE MODULE OR PC BOARD
The 5883 can be mounted remotely, or, with some controls, can be mounted inside the control's cabinet.
When mounting, make sure the antennas do not touch any metal surfaces.
First, Check for RF Interference:
use the red RF Interference LED (see figure 3) to check for strong
local radio frequency interference at the intended mounting location.
If this LED is continuously lit, the 5883 module should be relocated.
Removing the Cover
Remove the 5883's cover by inserting and twisting a screwdriver blade
in the slot at the center of the cover's lower edge.
Replace the cover when installation is complete if unit is not mounted
within a cabinet.
Mounting inside the control's cabinet (refer to Fig. 2):
1. Remove the 5883's circuit board from its base by bending back the
two flexible plastic tabs that hold the board's lower edge. Discard
the 5883's unused plastic cover and base.
2. In the control's cabinet, unfasten and move the control circuit board
downward (if already installed).
3. Hang two short (black) mounting clips (provided) on the raised
cabinet tabs in the cabinet, as shown in Detail B of Figure 2.
4. Insert the top of the 5883's board into the supporting slots at the top
of the cabinet (Detail A). Swing the bottom of the board into the two
short (black) mounting clips installed in step 3, and secure it to the
cabinet with the accompanying screws. See Detail B.
5. Insert the top of the control's board into the slot in the black clips
holding the lower edge of the 5883 board (see Detail B); position two
long (red) clips at the lower edge of the board (see Detail C).
6. Swing the lower edge of the control board into place, and secure with
two additional screws.
7. Insert the grounding lugs (provided) through the top of the cabinet
and into the left-hand terminals of the antenna blocks (at the upper
edge of the 5883's circuit board). Secure it to the cabinet with the
two screws provided. See Detail D.
8. Insert the 5883's two antennas through the two openings in the top
of the cabinet, one into each block's right-hand terminal, and tighten
the screws to secure them.
9. Affix the 5883's Summary of Connections label to the inside of the
control's cabinet door.
I N S T A L L A T I O N A N D S E T U P G U I D E
and
control
messages
from
Before mounting permanently,
RF Zones Supported
5883M
Up to 16 zones
5883H
Depends on the control with which it is used. See the
control panel's instructions for specific details.
If "SET UP ERROR" (alpha keypads) or "E4 or "E8"" (fixed-word
keypads) is displayed on the system's keypad, it indicates that
more than the permitted number of wireless zones have been
5800
programmed, and none of the zones will be protected.
Figure 1. Block Diagram
CONTROL
PANEL*
KEYPAD
TERMINALS
ON CONTROL
BOARD
DATA OUT
TO 5883
DATA IN TO
CONTROL
*CONTROL MUST BE CAPABLE OF
SUPPORTING A 5800 RF SYSTEM
BOARD
SUPPORTING
SLOTS
MOUNTING
CLIP
MOUNTING
CLIP
CABINET
+
ANTENNA AND GROUNDING LUG INSTALLATION
Figure 2. Installing the 5883 Board in the Control's Cabinet
(Check the control's Installation and Setup Guide for applicability.)
Mounting the 5883 remotely
NOTE: If mounting the 5883 in its own enclosure, the supplied PCB
mounting clips, grounding lugs, and screws are not needed.
1. All wiring between the 5883 and the control panel must be located
in a conduit.
2. For concealed wiring, route wires through the rectangular opening at
the rear of the base before mounting. For surface wiring entry, a thin
breakaway area is provided along the base's right edge.
3. Mount the module in the selected location. For greatest security,
use all four mounting holes (two keyslot holes and two round holes)
in the plastic base. (Refer to Detail D in Figure 2 above.)
4. Install each antenna in the respective right-hand terminal of the
two terminal blocks at the upper edge of the 5883's circuit board,
and tighten the screws to secure them.
5. Affix the 5883's Summary of Connections label to the inside of the
housing cover.
5800 SERIES
WIRELESS
TRANSMITTERS
2-WAY
TRANSMISSION
5883
TRANSCEIVER
HOLES FOR ANTENNAS
CABINET
AND GROUNDING LUGS
CIRCUIT BOARD
RECEIVER CIRCUIT BOARD
(See Detail D)
+
+
CONTROL
CIRCUIT
BOARD
SCREW
(2)
ANTENNA
(2)
GROUNDING
LUG
(2)
RCVR BRD
+
ANTENNA
MOUNT
(2 PLACES)
DETAIL D
K3791 3/04 Rev. B
2-WAY
WIRELESS
KEYPAD
(e.g. 5804BD)
OR
5800RL 2-WAY
RELAY MODULE
DETAIL A
SIDE VIEW
OF BOARD
SUPPORTING SLOTS
DETAIL B
SIDE VIEW
OF MOUNTING
CLIP
DETAIL C
SIDE VIEW
OF MOUNTING
CLIP
pcb_RF_mount-V0
Advertisement
Related Manuals for Honeywell Ademco 5883
Summary of Contents for Honeywell Ademco 5883
- Page 1 K3791 3/04 Rev. B I N S T A L L A T I O N A N D S E T U P G U I D E RF Zones Supported INTRODUCTION 5883M Up to 16 zones The 5883 RF Transceiver Module: 5883H Depends on the control with which it is used.
-
Page 2: Dip Switch Functions
1. Remove the PC board by bending back the two flexible plastic tabs Mounting for Commercial Fire Applications (in separate cabinet) that hold the board's lower edge. Discard the 5883’s unused plastic For Commercial Fire applications, the 5883 module must be mounted cover and base. -
Page 3: Specifications
PROGRAM THE CONTROL FOR RF OPERATION Proceed with any control panel programming that may be necessary for RF operation and the installation of the system's wireless transmitters, as described in the control's Installation And Setup Guide. In addition, note the following: Enable the appropriate control data field for RF usage. - Page 4 LIMITED WARRANTY Honeywell International Inc., acting through its Security & Custom Electronics business ("Seller") 165 Eileen Way, Syosset, New York 11791, warrants its product(s) to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and service for 24 months from the date stamp control on the product(s) or, for product(s) not having a manufacturer’s date...