Related Manuals for Honeywell HD28C4HR6
Summary of Contents for Honeywell HD28C4HR6
-
Page 1: Installation Guide
Premium Vandal Document 900.0275 – 10/05 – Rev 1.01 Dome Camera NTSC / PAL HD28C4HR6 HD28C4HR9 HD28W4HR6 HD28W4HR9 HD28D4HR6 HD28D4HR9 Installation Guide HD28C4HR6X HD28C4HR9X HD28W4HR6X HD28W4HR9X HD28D4HR6X HD28D4HR9X... - Page 2 Revisions Issue Date 1.00 09/05 1.01 10/05 Rev 1.01 Revisions New document. Changed HD28R to HD28 throughout, removed utp & fiber termination boards updated back cover. Document 900.0275 10/05...
-
Page 3: Explanation Of Graphical Symbols
Warnings Installation and servicing should be performed only by qualified and experienced technicians to conform to all local codes and to maintain your warranty. WARNING! The use of CSA Certified/UL Listed Class 2 power adapters is required to ensure compliance with electrical safety standards. -
Page 4: Fcc Compliance Statement
FCC Compliance Statement Information to the User: This equipment has been tested and found to comply with the limits for a Class A digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. -
Page 5: Table Of Contents
Contents Introduction ..........1 Before You Begin . -
Page 6: Introduction
• One product warranty If any parts are missing or damaged, contact the dealer you purchased the camera from or call Honeywell Customer Service (see “Warranty and Service” on page 12). Equipment Required You will require the following tools to complete the installation: •... -
Page 7: Installation
Installation Your HD28 camera is weather-sealed for indoor or outdoor locations. The wiring can be completely concealed for maximum vandal and tamper resistance. Mounting the Camera The HD28 camera is designed to be surface mounted on a wall or ceiling. Preparing the Mounting Surface Affix the mounting template to the mounting surface (see Pre-drill four holes as indicated on the template, using the recommended... -
Page 8: Installing The Conduit Plug
Installing the Conduit Plug Your HD28 enclosure comes with a conduit plug pre-installed in the 1/2” conduit entry on the back of the housing. This plug may be removed and installed in the side 3/4” conduit entry (see Figure 2 Conduit Plug Installation Back View Caution... -
Page 9: Wiring Options
Wiring Options Your HD28 Series camera is supplied with a coaxial termination board mounted to the bottom of the enclosure. All connections are made here (see Figure 3 Wiring Options Connecting the Wiring Pull the cables through either the back or the side conduit. To minimize moisture leaking into the housing, position the enclosure with the conduit pointing down. -
Page 10: Adjusting The Camera
Figure 4 Gimbal Adjustment Legend 1 = Pan rotation 2 = Horizontal rotation 3 = Tilt rotation Adjusting the Lens Focus Lenses are pre-focused at the factory but may require a final adjustment after installation in the unlikely event the optical effect of the dome causes a slight defocusing of the lens. -
Page 11: Dip Switch Functions (Color Cameras, Including Tdn Models)
Dip Switch Functions (Color Cameras, Including TDN Models) Follow Figure 5 to set the dip switches on a color camera. Figure 5 Color Camera Switch Settings * Not used. Leave in Off position. Auto Iris Level Adj. (Varifocal lens). Turn screw clockwise to increase brightness level. -
Page 12: Adjustment Method (Color Cameras)
Adjustment Method (Color Cameras) Switch no. Function GAMMA AE (Automatic Exposure) FLON (Flicker Less) BLC (Backlight Compensation) IRIS Control Not used White Balance Adjustment Method (Color Cameras) Symbol Push lock Indoor (3200° K) Outdoor (6500° K) * To manually set Push lock feature: place a white background in front of camera and press “Push lock”... -
Page 13: Manually Setting Shutter Speed (Color Cameras)
Manually Setting Shutter Speed (Color Cameras) To manually set the shutter speed, turn switch #2 to the ON position; then set switch #3, #4, and #5 for the desired shutter speed (see Shutter speed(s) 1/50 (PAL) 1/60 (NTSC) 1/100 (PAL) 1/120 (NTSC) 1/250 1/500... -
Page 14: Dip Switch Functions (Wdr Cameras)
Dip switch functions (WDR cameras) Figure 6 Wide Dynamic Range Camera Switch Settings Line-lock adjustment Auto Iris level adjustment. If necessary, turn clockwise to increase brightness level. Note The Wide Dynamic Range camera has been designed for the best wide dynamic performance and can only be used with vari-focal auto iris lenses. -
Page 15: Adjusting The Line Lock (Vertical Phase) For 24 Vac Operation
Adjusting the Line Lock (Vertical Phase) for 24 VAC Operation Phase adjustment may be necessary in multiple camera installations to prevent picture roll when switching between two cameras. To adjust the vertical phase while switching between two cameras, turn the Line lock adjustment screw on one camera until there is no vertical roll. -
Page 16: Routine Maintenance
Video switcher or other equipment connections. To eliminate video problems, connect a video monitor directly to the HD28 video output cable. Noisy video Check: • Video ground connections • For ground loops. For additional assistance, call Honeywell Customer Service (see below). Rev 1.01 Document 900.0275 10/05... -
Page 17: Warranty And Service
Warranty and Service Subject to the terms and conditions listed on the product warranty, during the warranty period Honeywell will repair or replace, at its sole option, free of charge, any defective products returned prepaid. In the event you have a problem with any Honeywell product, please call Customer Service at 1.800.796.2288 for assistance or to request a Return... -
Page 18: Specifications
Specifications Note Specifications apply to all camera models, unless otherwise noted. Video Signal Specifications Pickup device: Electronic iris: Surge protection: Video output: Coaxial Video signal: Light sensitivity: Color, Including TDN Wide Dynamic Resolution: Backlight compensation: Auto white balance: (Color cameras only) Power Requirements Input voltage (at camera): Current consumption:... -
Page 19: Cable Guidelines
Calculations are based on an unregulated linear power supply which would be the Note worst case. Using a regulated or switching power supply can increase the cable distance. Honeywell recommends using a CSA Certified/UL listed Class 2 power supply to ensure compliance with electrical safety standards. Coaxial video cable maximum length (feet/meters) - Page 20 All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof.