LCD TV SERVICE MANUAL CHASSIS : LB61A FACTORY MODEL : 32LC2D-AA MODEL : 32LC2D CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards.
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service unit under test. manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or...
Page 5
IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through Circuit Board Foil Repair which the IC leads are inserted and then bent flat against the Excessive heat applied to the copper foil of any printed circuit circuit foil. When holes are the slotted type, the following technique board will weaken the adhesive that bonds the foil to the circuit should be used to remove and replace the IC.
ADJUSTMENT INSTRUCTION 1. Application Object 5. MST3362M-Set Adjustment These instructions are applied to all of the 32" LCD TV, 5-1. Synopsis LB61A Chassis MST3362M-Set adjustment to set the black level and the Gain of optimum with an automatic movement from the analog => 2.
6. Video(uPD)-Set Each PCB Assy must be checked by Check JIG Set before assembly. (Especially, be careful Power PCB Assy which can 6-1. Synopsis cause Damage to the PDP Module.) This is a adjustment to reduce the color difference of video signal Main/Sub Display.
8-3. EDID DATA 8. EDID(The Extended Display (1) HDMI EDID DATA. Identification Data)/DDC 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F (Display Data Channel) Download 00 00 FF FF FF FF FF FF 00 1E 6D 01 01 01 01 01 01 10 0A 10 01 03 80 6E 3E 78 0A 31 30 A5 58 3B B8 26 This is the function that enables “Plug and Play".
Page 13
8-4. Act or set the EDID S/W 9. Adjustment of White Balance 1) As above Fig. 6, Connect the Set, EDID Download Jig, PC 9-1. Required Equipment & Cable. 2) Turn on the PC & EDID Download Jig. And Execute the (1) Color analyzer (CA-210 or similar product) S/W : EDID TESTER Ver,2.5.
Page 14
9-4. Adjustment of White Balance (Automatic Adjustment) Calibrate of the CA-210, then attach sensor to PDP module surface when you adjust. Manual adjustment is also possible by the following sequence. (1) HEAT RUN at least 30 minutes by pressing the Power only Key on the Service Remote Control and adjust.
Page 15
10. Shipping Conditions Item Value Remark Power CH Memory Analog C0,C5,C6,S11,S28,C27,C44,C60 Digital Pictur Dynamic Contrast Brightness Color Sharpness Tint (Not available) Color temperature COOL Auto , Manual Audio Standard Balance Treble Bass Front surround TV speaker Time Auto clock Manual Clock Enable Off timer On timer Sleep timer...
SVC REMOCON FUNTION REAMARK To turn the TV on or off POWER To turn the TV on automatically if the power is supplied to the TV. (Use the POWER ON POWER key to deactivate): It should be deactivated when delivered. To activate the mute function.
TROUBLESHOOTING 1. Power Board 1-1. The whole flowchart which it follows in voltage output state Start check Doesn't the Is it identical Is the Interface screen whole come with Power Off signal operated? out? condition? 1. Check the Power Off 2.
Page 18
1-2. 42” Power Board Structure T801: Vs Trans T901: Va Trans T112: Low Voltage Trans T501: ST-BY Trans T601: PFC Inductor - 18 -...
Page 19
2. In case of occurring strange screen into specific mode 2-1. In case the OSD does not displayed (1) Symptom 1) LED is white. 2) Some discharge on Panel becomes accomplished continuously. (2) Check follow Is the LVDS cable Is the LVDS cable Replace the cable.
Page 20
2-2. In case of does’t display the screen into specific mode (1) Symptom 1) The screen does not become the display from specific input mode. (RF, AV, Component, RGB, DVI) (2) Check following 1) Check the all input mode should become normality display. 2) Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become normality display from the PIP mode or DW mode.(Re-Check using Swap function) Check the NEC64015(IC701) if the main picture is abnormal, and...
Page 21
(5) When Component or RGB-DTV/ PC mode is abnormal Is the CXA2151Q(IC500) Is normal the Input voltage, IIC Replace the IC. normal? Communication and HV sync? Is the MST3362(IC604) Is normal the Input voltage, IIC Replace the IC. normal? Communication and HV sync? Is normal the Input voltage, IIC Is the Scaler normal? Replace the IC.
Page 22
3. When sound is abnormal (1) Symptom 1) LED is green. 2) Screen display but sound is not output. (2) Check following Is the SPK cable Is the SPK cable Replace SPK cable. normal? connected well? Cable inserts well. Is the Flat cable Cable inserts well.
Speaker,Fullrange, C112K01K1450. FERRITE 15W 8OHM 83.5DB 170HZ 116 X 42 X 38.5 LUG ESTEC AMERICA CORPORATION 49509K0195A Plate, CASTING AL FRAME SUPPORT 32LC2 EBR30742201 PCB Assembly,Sub, SUB T.T LB61A 32LC2D-AA AAULLHX SIDE AV TOTAL_DMS apply EBR31378301 PCB Assembly,Sub, SUB T.T LB61A 32LC2D-AA AAULLHX KEY FRONT TOTAL EBR31311501 PCB Assembly,Sub, SUB T.T LB61A 32LC2D-AA AAULLHX IR FOR DMS...
REPLACEMENT PARTS LIST For Capacitor & Resistors, the CC, CX, CK, CN, CH : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit in the CQ : Polyestor RS : Metal Oxide Film P/No. means as follows; CE : Electrolytic RN : Metal Film CF : Fixed Film RH : CHIP, Metal Glazed(Chip)