Version 1.3 Created in December 2004 Instruction Manual Thank you for purchasing our IV-08MTV LCD Color Monitor. Before using it, read this manual carefully to IV-08MTV become familiar with its functions and proper LCD Color Monitor use. Notes - This manual was written with the utmost care. However, if you have any questions or inquiries concerning the product, please feel free to contact our dealers or service agents.
- If you need to plug the monitor into a 200 VAC outlet, please contact our sales division or the shop where you purchased the monitor. - Do not use the specialized AC cord and adapter that come with the IV-08MTV to power any other devices.
Page 3
The Monitor can be used as a display monitor for any equipment with an NTSC output, such as the SHARP IV-S30 series, IV-C35M etc., and it can be used as a monitor for the SHARP IV-S51M (analog RGB output) or as a monitor for a personal computer.
2. Precautions for Use Please note the following points when handling the Monitor. (1) Installation location and environment - The Monitor should be used in a location with an ambient temperature of 0 to 45 C and a relative humidity of 90%RH or less. If the ambient temperature is higher than the maximum temperature above, install a fan for forced air cooling or an airconditioner to conditioning the space to bring the ambient temperature within the specified range.
3. System Configuration IV-08MTV IV-S30 series IV-C35 Monitor cable *2 (cable length: 2 m) Adj. POWER IV-S51M IV-S51M POWER +24V TERMINATOR LINK ANALOG HALT C (-) CAMERA1 Video cable IV MONITOR ONLY CAMERA2 Analog RGB cable (Commercially available item: (Commercially available item)
4. Name and Function of Each Part [Top view] 220.6 (Unit: mm) (7) Mounting holes (4 positions: two at bottom) [Side view] [Front view] 53.3 POWER Adj. (5) Power lamp Power key [Rear view] (8) M4 Screw hole (4 positions: For the mounting stand) (9) Cable clamp ANALOG VIDEO...
Page 7
- Connect a monitor cable here (IV-S30/C35M accessory). Terminal used to output an NTSC video signal from the Monitor. Video output terminal - Connect another video monitor here (or IV-08MTV) to see the same (VIDEO OUT) image elsewhere at the same time.
(4, including 2 on the bottom) IV-08MTV (See the cross section view below) 2) Insert a mounting bracket (2 each at the top and bottom) into each mounting hole on the housing, and secure the mounting brackets using the mounting screws.
Page 9
[Rear view when mounting the Monitor using the mounting brackets] 220.6 (Unit: mm) - 8 -...
Page 10
When using the specialized stand Install the Monitor on the specialized stand (custom order item). Then the Monitor can be used in a standalone configuration. Rotation center IV-08MTV Stand Dimensional drawings when the Monitor is installed on the stand Mounting screws on...
[1] To connect the Monitor to an IV-S30 series controller or an IV-C35M Connect the NTSC video input terminal (VIDEO IN) on the Monitor to the monitor connector on the IV- S30 series (controller), or the IV-C35M, using the monitor cable (*1). [Rear view of the IV-08MTV] IV-S30 series IV-C35M...
Page 12
Connect the analog RGB connector (ANALOG RGB) on the Monitor to the analog connector on the IV- S51M or personal computer using an analog RGB cable (purchase one locally). A connection example using an IV-S51M is shown below [Rear view of the IV-08MTV] IV-S51M IV-S51M...
Page 13
AC cord from the adapter (*2) into a 100 VAC power outlet. Make sure to connect the ground line on the power cord plug to a ground terminal on the power outlet. [Rear view of the IV-08MTV] AC adapter *2...
Page 14
[4] To connect two IV-08MTV monitors Connect the NTSC video output terminal (VIDEO OUT) on the IV-08MTV to the NTSC video input terminal (VIDEO IN) on another IV-08MTV using a standard video cable (available locally: less than 10 m). Then, you can monitor simultaneously at another location.
LANGUAGE JAPANESE/ENGLISH (JAPANESE) OSD H-POS (50) OSD V-POS (50) OSD TIMER (11) OSD DISPLAY OSD TRANSPARENCY (50) RECALL RETURN TIMER (0) TIMER * MODEL SELECT SHARP IV/OTHER (SHARP IV) VIDEO 1 SOURCE ANALOG RGB RETURN RECALL EXIT - 14 -...
Page 16
(2) When an analog RGB input signal is used Main menu Detailed menu (default values) BASIC ADJUST AUTO SETUP AUTO COLOR ADJUST RETURN BACKLIGHT (85) BRIGHTNESS (100) LUMINANCE CONTRAST (100) RECALL RETURN H.POSITION (43) V.POSITION (56) CLOCK (50) PHASE (0) DISPLAY SHARPNESS (0) QUALITY (20)
8. Specifications (1) General specifications Item Specifications 100 to 240 VAC, 50/60 Hz (using the accessory AC adapter) Power supply Power consumption 10 W Ambient storage - 20 to + 60 temperature Ambient operating 0 to 45 temperature Ambient humidity 35 to 90 %RH (non condensing) Environmental No corrosive gases...
Page 18
(2) Performance specifications Item Specifications 8.4 inches diagonal: 170.4 W x 127.8 H mm Display size Transmissive type TFT liquid crystal panel Display type TFT active matrix driving system Driving system 921,600 pixels: (640 W x 480 H) x 3, Ratio of functional pixels: 99.99% Number of pixels or better Approximately 262,000 colors...