Advertisement
Quick Links
You must be fully aware of all the distinctive
features and precautions related to this
COMPOSITION:
camera before installing it.
Service Monitor Cable
L-Wrench
Operation Manual
Mounting Screw
INSTALLATION:
Ceiling
1
Stick the guide pattern on the
wall or ceiling.
2
Drill four holes according to
the guide pattern then insert
anchors into the drilled holes.
3
Draw out power / video wires
to the connecting places.
4
Fix the camera to a celling using
four screws.
5
Adjust desired focus and scene
by turning and moving the
3-axis camera bracket by hand.
6
Put the dome cover over the
base.
7
Fix the dome cover on the base
by L-Wrench.
PRECAUTIONS:
!
Do not install the camera in
extreme temperature conditions.
Do use the camera under conditions
where temperatures are within
-20¡ÆC to 45¡ÆC.
Be especially careful with ventilation
under high temperatures.
!
Do not disassemble the camera.
There are no user-serviceable parts
inside it.
!
Do not drop the camera or
subject them to physical shocks.
It can cause malfunctions to occur.
!
Note
When this camera is installed near
wireless communication devices
that emits strong electromagnetic
field, irregularity such as noise on
the monitor may appear.
CONNECTION:
#1
Connecting to
Monitor and Power
12VDC Power Type
#2
DIMENSIONS(mm):
100.0
Guide Pattern
142.4
¡Ø 3/4 JIS B0202-1982
SPECIFICATIONS:
Model
Signal System
Scanning System
Guide Pattern
Scanning Frequency ( H )
Scanning Frequency ( V )
Image Sensor
Total / Effective Pixels No.
S / N Ratio
Dome Base
Resolution
Video Output Level
Lens
Focus
Sync. System
Sensitivity
Mounting
Electronic Shutter
Screw
White Balance
AGC
BLC
Flickerless
Dome Cover
Input / Output Connector
Power Consumption
Dome Size ( Ø )
Weight
L-Wrench
Call 1.800.796.CCTV for sales, service and customer support.
NAME AND FUNCTION:
Fixed Lens & IR LED Type
1
2
Tilt rotation: Adjusting the vertical angle.
1
Pan rotation: Adjusting the horizontal angle.
2
3
Horizontal rotation: Adjusting the horizontal
position of the screen.
• Power Consumption: 5W
IR LED (4mm Fixed Lens)
• IR LED Specification: 850nm / 30¡Æ(24EA)
• The wire is polarized. • Use 12VDC
Video Output
Video
(Yellow)
No.
Function
#1
Video Output
GND
#2
Power Input
Power - 12VDC
(Red)
NTSC
PAL
NTSC : 525 Lines
PAL : 625 Lines
2 : 1 Interlace
15.734kHz
15.625kHz
59.94Hz
50Hz
1/3" SONY Super HAD CCD
410K / 380K
470K / 440K
More than 50dB (AGC Off)
550 TV Lines
1.0 Vp-p (75 Ohms, composite)
Fixed Lens : f=4.0mm
Manual
Internal
0 Lux, IR LED
1/60 ~ 100,000 Sec.
1 /50 ~ 100,000 Sec.
Auto
On / Off
On / Off (with Slide Switch)
On / Off (with Slide Switch)
Power, Video
12VDC (10V~15V) / 5W (Max)
100mm
Approx. 844g
Need Help?
www.honeywellvideo.com
Design and specifications are
subject to change without notice.
5
4
3
IR LED: 850nm / 30¡Æ(24EA)
4
Sensor
5
Camera Lay-out
power source.
Terminal Color
Remark
Yellow
1.0 Vp-p
Red
12VDC, Max 5W/ 400mA
HD70
Series
Operation
Manual
• 1/3" Sony Super HAD CCD
• High Resolution:550 TV Lines
• 4mm Fixed Lens
• Color Day/Night with 24 LEDs
• Auto White Balance
• AGC, BLC, Flickerless On/Off
• Extra Video Output for Installer
• 3-Axis Camera Construction
• Vandal-Resistant Dome Housing
3-axis
Built-in
camera
bracket makes it much
360º
easier to rotate in any
direction.
CAMERA SET-UP:
Fixed Lens & IR LED Type
a
Function Selection Switch:
J504
•FL(Flickerless) ON/OFF
AC24V
•AGC(Auto Gain Control) ON/OFF
b
•BLC(Back Light Compensation)
ON/OFF
Service Monitor Connecter:
b
Use service monitor connector
to set camera angle & focus
AC 24V
when installing.
J503
BLC
ON
AGC
OFF
CAUTION : When AGC is off,
FL
ON
D/N does not work because the
a
D/N switching function is
dependent on the AGC level.
TROUBLESHOOTING:
If you have trouble operating your camera, refer to the following.
If the guidelines do not enable you to solve the problem, contact an authorized technician.
Check the power source for the monitor and camera
The image does not
and ensure that the voltage and polarity are properly
appear on the screen.
connected and being supplied correctly.
Check if the lens is stained. If dirty, clean the lens with
The image on the
a soft, clean cloth.
screen is dim.
Adjust the Back Focus of the lens again.
Check if you have connected the camera to a proper
The camera does not work
properly, the surface of the
power source and If there is no problem with the power,
camera case is hot, and a black
turn the unit off immediately and seek assistance from
line appears on the screen.
our Customer Service department.
Check if the camera is pointed toward the sun or a
The screen blinks a lot.
fluorescent lamp.
Adjust the angle or location of the camera if too much
light is coming into the screen.
READ AND KEEP THIS
OPERATION MANUAL
90º
360º
Advertisement
