Fujitsu SERVICE MANUAL COLOR MONITOR MCM1514V D556Q 154V/C551 41A50-108-01...
Page 2
THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY. EVERY REASONABLE EFFORT HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL; WE CANNOT GUARANTEE THE ACCURACY OF THIS INFORMATION AFTER THE DATE OF PUBLICATION AND DISCLAIMS LIABILITY FOR CHANGES, ERRORS OR OMISSIONS,...
2. PRECAUTIONS AND NOTICES SAFETY PRECAUTIONS Observe all caution and safety related notes located inside the display cabinet. Operation of the display with the cover removed, may cause a serious shock hazard from the display power supply. Work on the display should not be attempted by anyone who is not thoroughly familiar with precautions necessary when working on high voltage equipment.
HIGH VOLTAGE WARNING Operation of monitor outside of cabinet or with back removed may cause a serious shock hazard. Work on this model should only be performed by those who are thoroughly familiar with precautions necessary when working on high voltage equipment. Exercise care when servicing this chassis with power applied.
3. OPERATING INSTRUCTIONS This procedure gives you instructions for installing and using the 154V/C551 Series display. Position the display on the desired operation and plug the power cord into a convenient AC outlet. Three-wire power cord must be shielded and is provided as a safety precaution as it connects the chassis and cabinet to the electrical conduit ground. If the AC outlet in your location does not have provisions for the grounded type plug, the installer should attach the proper adapter to ensure a safe ground potential.
4. ADJUSTMENT ADJUSTMENT CONDITIONS AND PRECAUTIONS Approximately 30 minutes should be allowed for warm up before proceeding. Adjustments should be undertaken only on those necessary elements since most of them have been carefully preset at the factory. 4-2 MAIN ADJUSTMENTS FUNCTION LOCATION DESIGNATION...
Page 9
4. Focus adjustment: × A. Set mode 2 ( 640 480 Fh: 31.5KHz ) with character full page. B. Adjust external brightness to raster cutoff and external contrast to max. , then adjust focus VR to make the display be focused very well.
5. CIRCUIT DESCRIPTION 5-1 MICRO CIRCUIT IC101 is CPU, This CPU has the following functions. 1. Detect timing mode by sensing the horizontal frequency, vertical frequency, the polarity of Hor. Sync and Ver. Sync. 2. Key board scan control. 3. Cs capacitor switch control. 4.
5-5 TRANSISTOR & DIODE CIRCUIT LOCATION CIRCUIT FUNCTION DESCRIPTION D901 ~ D904 Bridge Rectifier for AC Source D909 Half-Wave Rectifier for Start CKT D910 Clamp Diode for Snubber CKT D919 Rectifier for Output Voltage D922 Rectifier for Output Voltage D923 Rectifier for Output Voltage D925 Rectifier for Output Voltage...
6.TROUBLE SHOOTING CHART 6-1 NO RASTER, CRT RELATIVE CIRCUIT PROBLEMS 1.ABNORMAL POWER SUPPLY 90V,12V CHECK MAIN PC BOARD CHECK POWER SAVING CIRCUIT Q909,Q910 CHECK THE HIGE VOLTAGE OF CRT ABOUT 23.5 ~ 25.5KV CHECK FAILSAFE CKT Q402,Q403 RELATIVE CKT. CHECK THE VOLTAGE OF CRT HEATER ABOUT 6.3V CHECK CRT’S HEATER RELATIVE CIRCUIT Q907,Q908...
Page 13
2.ABNORMAL VIDEO LEVEL ON SCREEN CHECK THE VOLTAGE OF IC801 PIN 2,16 ABOUT 8V CHECK 8V RELATIVE CIRCUIT CHECK THE SIGNAL INPUT OF R.G.B. ABOUT 0.7Vpp CHECK SIGNAL CABLE OR INTERFACE CARD. CHECK IC801 PIN 11 ABOUT 10Vpp CHECK THE RELATIVE CIRCUIT OF Q813,Q814 OR CLAMP.
6-2 ABNORMAL DISPLAY NO SIGNAL ON SCREEN CHECK VIDEO IC VCC ABOUT 8V CHECK THE 12V PIN OF P802 CONNECTOR CHECK THE OUTPUT VOLTAGE OF IC801 PIN 13,15,18 ABOUT 3Vpp CHECK THE RELATIVE CIRCUIT OF Q813,Q814 & IC801 CHECK THE B+ VOLTAGE OF VIDEO PCB ABOUT 75V CHECK THE 80V RELATIVE CIRCUIT OF SMPS ON MAIN PCB...
6-4 HOR./OSC/DEF/HV CIRCUIT FAULT NO RASTER (DISCONNECT WITH SIGNAL CABLE) CHECK IC401 PIN 29 ABOUT 11.5VDC CHECK IC401 PIN 29 RELATIVE CIRCUIT CHECK IC401 PIN 26 WAVE FROM ABOUT 3Vpp CHECK IC401 PIN 4 ~ 7, PIN 13 RELATIVE CIRCUIT CHECK THE COLLECTOR VOLTAGE OF Q402 ABOUT 30Vpp FROM ABOUT 3Vpp...
6-9 POWER SUPPLY TROUBLE SHOOTING CHART BEFORE CHECK SW.REG. PLEASE REFER TO THE POWER SUPPLY BLOCK DIAGRAM POWER SUPPLY OUTPUT: (A) VARIABLE OUTPUT : 90V - 160V (DEPENDING UPON H.SYNC FREQUENCY) (B) CONSTANT OUTPUT : 6.3V, 15V, -12V, 75V BEAD SET ABNORMAL VARIABLE OUTPUT CHECK AC LINE MAKE SURE THAT...
PARTS LIST OF CABINET LOCATION 154V/C551 SPECIFICATION (LOW RADIATION 220V) CMC556DQJ2 CHAS ASS'Y 503- SCREW RUBBER WASHER TERMINAL LUG 112- WIRE MOUNTS 112- WIRE MOUNT 115- FBT CLIP 6015 CRT SUPPORT 403- BUMPER STEEL SPRING 3598- ABS PLASTIC 3710- FUNC LED LENS 3735- KEY PAD 643-...
Page 22
PARTS LIST OF CHAS LOCATION 154V/C551 SPECIFICATION CMP556DQJAI MAIN PC BOARD ASS'Y CRPC556DQJ2 CRT BOARD ASS'Y 421- SCREW LOCK WASHER 121- PC SUPPORT 5640- AL GND LUG 5643- REAR BRACKET 3662- LED HOLDER 581- 26 - CHASSIS LABEL 500- CABLE TIE FERRITE BEAD 100- FERRITE CORE...
Page 31
J041 TIN COATED J042 TIN COATED J043 TIN COATED J044 TIN COATED J045 TIN COATED J046 TIN COATED...
Page 32
LOCATION 154V/C551 SPECIFICATION J049 TIN COATED J050 TIN COATED J051 TIN COATED J052 TIN COATED J053 TIN COATED J054 TIN COATED J057 TIN COATED J058 TIN COATED J061 TIN COATED J063 TIN COATED J064 TIN COATED J065 TIN COATED J066 TIN COATED J067 TIN COATED...
Page 33
J120 TIN COATED J121 TIN COATED J123 TIN COATED J125 TIN COATED...
Page 34
LOCATION 154V/C551 SPECIFICATION J130 TIN COATED J132 TIN COATED J133 TIN COATED J134 TIN COATED J914 TIN COATED L101 339 - 3.3UH +-10% L402 TIN COATED L403 TIN COATED L406 TIN COATED L907 TIN COATED Q101 446- 2SC1213AC Q401 419- 2SC945P Q404 420-...
Page 45
PARTS LIST OF Q403/Q406/D408 ASS'Y LOCATION PARTS No. SPECIFICATION NYLON WASHER 3028- MICA 354- HEAT SINK 1730- SCREW 1730- 10 - SCREW D408 220- FMP-2FUR 1500/600V 5A Q403 689- 2SC5297 Q406 415- TIP122 PARTS LIST OF AC LINET ASS'Y LOCATION PARTS No.
10. IC BLOCK DIAGRAMS IC101 UM6862/WT6018 DEGAUSS V-I/P BRIGHT H-I/P CONTRAST RESET_ OSC0 OFF MODE IC802 LM2438T OSC1 H-OUT Vin 1 V-OUT Vin 2 Vin 3 WRITE PROTECT MUTE Vout 3 STAND BY/SUSPEND Vout 2 H.W DDC Vout 1 SENSE AUDIO KEY SELECT LED DETECT...
Page 51
IC102 24C04 HV GENERATOR MEMORY EEPROM ARRAY CONTROL CONTROL (128X8) LOGIC LOGIC XDEC PAGE LATCHES YDEC SENSE AMP R.W CONTROL IC601 TDA9302H FLYBACK GENERATOR POWER AMPLITIER THERMAL PROTECTION IC901 3842 SET/ Vref Vref RESET U.V.L.O. INTERNAL LOGLC BIAS 1/2 Vref C.S.
Page 53
IC801 LM1279N RED OSD IN GREEN OSD IN BLUE OSD IN CONTRAST 12dB DRIVE ATTENUATOR ATTENUATOR RED VIDEO IN RED OUT R CLAMP CAP RED DRIVE 1.35V CONTRAST 12dB DRIVE Vref ATTENUATOR ATTENUATOR VCC2 GREEN VIDEO IN GROUND GREEN OUT G CLAMP CAP GREEN DRIVE CONTRAST...