Related Manuals for Miele Miele@home XKM 2000 KM
Summary of Contents for Miele Miele@home XKM 2000 KM
- Page 1 Fitting and installation instructions Miele|home Con|ctivity XKM 2100 KM en - GB M.-Nr. 07 828 230...
-
Page 2: Table Of Contents
How the Miele|home system works ........ -
Page 3: Warning And Safety Instructions
Warning and safety instructions The electrical safety of this This appliance complies with all appliance can only be guaranteed relevant legal safety requirements. when continuity is complete between it Improper use of the appliance can and an effective earthing system which present a risk of both personal injury complies with current local and national and material damage. - Page 4 Installation, maintenance and This appliance is not intended for repairs may only be carried out by a use by persons (including children) Miele authorised person in strict with reduced physical, sensory or accordance with current national and mental capabilities, or lack of local safety regulations.
-
Page 5: Electrical Connection
Electrical connection All electrical work should be carried Ensure power is not supplied to the out by a suitably qualified and appliance until after installation work competent person in strict has been carried out. accordance with current local and national safety regulations (BS 7671 The appliance must only be in the UK). - Page 6 If the connection cable is damaged, it must be replaced by cable type H 05 V V-F (pvc insulated), available from the Miele Spare Parts Department. If the appliance is connected via a fused spur, the electrical cable must only be replaced by a suitable qualified electrician in accordance with local and national safety regulations.
-
Page 7: Description Of The Appliance
Description of the appliance Miele|home connection box a Shaft with communication module fitted b Data line c Connection point for mains connection cable 1 connection cable with plug 1 connection cable with wire end ferrules Accessories supplied: Adapter... -
Page 8: Connecting The Communication Module
Connecting the communication module Data line The connection point for the data line is located underneath the hob. The following illustrations are examples. The connection position may vary. Type 1 Type 2 Type 3... - Page 9 Use the adapter supplied for connection types 1 and 2. ^ Replace the cover and secure with the screws (Type 1 and Type 2 connections). ^ Connect the Miele|home connection box to the mains supply. The Miele|home connection box must not be screwed...
-
Page 10: Con|Ctivity
Con|ctivity How the Con|ctivity system works Con|ctivity is the communication between the hob and the cooker hood. The operation of the cooker hood is automatically controlled by the operating status of the hob. For communication to take place, the cooker hood must be fitted with communication module XKM 2000 DA a and the hob must be fitted with communication module XKM 2100 KM b. -
Page 11: Establishing Connection
All other hobs: please refer to the "Con|ctivity / Miele|home" section in the operating instruction manual for your hob. If the signing on process is unsuccessful, repeat the procedure. If this does not solve the problem, call the Miele Service Department. -
Page 12: Con|Ctivity And Miele|Home
Con|ctivity Con|ctivity and Miele|home To install Con|ctivity and Miele|home for the first time ^ Select the correct installation option (see chart in "Miele|home / Installation options"). Carry out the first installation without signing on the cooker hood and the hob. -
Page 13: Miele|Home
How the Miele|home system works Communication enabled appliances use the existing household power supply (Powerline communications) to transfer data to Miele|home master appliances (e.g. the InfoControl unit, the SuperVision appliance). You can use the master appliance to call up information about communication enabled appliances, such as programme status or fault messages at any time. - Page 14 – Dishwashers fridge/freezers. A wine storage unit will be shown as – Steam ovens a fridge. Sets the time for the Miele|home system. – Combi steam ovens InfoControl Receives and displays data from up to 8 signed on (master appliance) appliances.
- Page 15 – The SuperVision appliance must be fitted with Communication module XKM 2000 SV. – The First installation of the Miele|home system only needs to be carried out once. – The appliances remain signed on even if the SuperVision appliance is switched off.
-
Page 16: Installation Options
Miele|home Installation options Please make sure you know how to use your Miele|home enabled appliances and the InfoControl unit (if present) before you start. Please read the operating instructions supplied. Please also observe the Warning and Safety instructions contained in the operating instructions. -
Page 17: Miele|Home First Installation
^ Select that installation has been successful by pressing the # button on the base station. If acitvation is not successful, repeat the procedure. If this does not solve the problem, call the Miele Service Department. Signing on the hob... - Page 18 If you do not press the "#" button to confirm, the display will go out after 10 minutes. ^ Confirm the signing on process on the hob. If the signing on process is unsuccessful, repeat the procedure. If this does not solve the problem, call the Miele Service Department.
-
Page 19: First Installation Of The Supervision Appliance And Signing On Of The Hob
^ Start the signing on process on the hob. Induction hob KM 59**: see "KM 59**" All other hobs: please refer to the "Con|ctivity / Miele|home" section in the operating instruction manual for your hob. During the hob signing on process, you will be asked to... - Page 20 ^ Confirm that signing on has been successful with "OK". ^ Confirm the signing on process on the hob. If the signing on process is unsuccessful, repeat the procedure. If this does not solve the problem, call the Miele Service Department.
-
Page 21: First Installation Of The Infocontrol Unit And Supervision Appliance, Signing On Of The Hob
Start the signing on process on the hob. Induction hob KM 59**: see "KM 59**" All other hobs: please refer to the "Con|ctivity / Miele|home" section in the operating instruction manual for your hob. ^ Now sign on the SuperVision appliance. - Page 22 If you do not press the "#" button to confirm, the display will go out after 10 minutes. ^ Confirm the signing on process on the hob. If the signing on process is unsuccessful, repeat the procedure. If this does not solve the problem, call the Miele Service Department.
-
Page 23: Miele|Home Installation At A Later Date
^ Start the signing on process on the hob. Induction hob KM 59**: see "KM 59**" All other hobs: please refer to the "Con|ctivity / Miele|home" section in the operating instruction manual for your hob. During the hob signing on process, you will be asked to... - Page 24 If you do not press the "#" button to confirm, the display will go out after 10 minutes. ^ Confirm the signing on process on the hob. If the signing on process is unsuccessful, repeat the procedure. If this does not solve the problem, call the Miele Service Department.
-
Page 25: Signing On The Hob To The Supervision Appliance At A Later Date
^ Confirm that signing on has been successful with "OK". ^ Confirm the signing on process on the hob. If the signing on process is unsuccessful, repeat the procedure. If this does not solve the problem, call the Miele Service Department. -
Page 26: Signing Off The Hob
The signing off process must be carried out on the Miele|home master appliance and on the hob. Signing off ^ Switch on the Miele|home master appliance and start the signing off process (see the operating instructions for the relevant appliance). -
Page 27: Signing On/Off Km 59** Hobs
^ Touch the hob ON/OFF sensor s until the displays go out to save the setting. If the signing on process is unsuccessful, repeat the procedure. If this does not solve the problem, call the Miele Service Department. - Page 28 Signing on/off KM 59** hobs Signing off ^ With the hob switched off, touch the hob ON/OFF sensor s and the safety lock sensor $ at the same time until the indicator for the safety lock flashes. After the programming mode has been called up, P (Programme), S (Status) and numbers will appear in the cooking zone displays.
-
Page 29: Problem Solving Guide
There was a problem with appliances" function on installing the SuperVision / the master appliance. InfoControl master appliance at a later date. ^ Refer to the chart in The hob is not suitable for "Miele|home". displaying on the SuperVision appliance or the InfoControl unit. - Page 30 ^ Repeat the signing off The signing off There was a problem procedure on the hob. procedure on the hob during the signing off has been unsuccessful. procedure. You cannot resolve the problem. Please contact your Miele Dealer or the Miele Service Department.
- Page 32 Alteration rights reserved / 3212 M.-Nr. 07 828 230 / 01...