Mixer section
1
2
3 45
PHONO1/
DECK1
LINE1
HEADPHONES
MIXING
j
CUE
MASTER
LEVEL
i
0
CH1
CH2
h
g
b
10
9
8
7
6
d
5
4
3
2
1
0
1 DECK1/PHONO1/LINE1 selector switch
This selects the [CH 1] input source from among the devices con-
nected to this unit.
! When set to [PHONO/LINE], the mixer section can be used as a
DJ mixer. In this case, the effect sections of the respective decks
can be used.
2 EQ (HI, MID, LOW) controls
These adjust the sound quality of the respective channels.
These adjust the [HI] (high range), [MID] (middle range) and [LOW]
(low range), respectively.
3 TRIM control
Adjusts the level of audio signals input in each channel.
4 LEVEL indicator
This displays the audio levels of the respective channels.
! Press the [MASTER] button to switch the channel whose audio
level is displayed.
5 MASTER LEVEL control
Adjusts the audio level output from the [MASTER OUT 1] and
[MASTER OUT 2] terminals.
6 MASTER button
This switches the channel indicated on the [LEVEL] indicator.
— When off: The audio level input to [CH 1] (channel 1) and [CH 2]
(channel 2) is displayed on the [LEVEL] indicator.
— When lit: The audio level output from the [MASTER OUT 1] and
[MASTER OUT 2] terminals is displayed on the [LEVEL] indicator.
7 DECK2/PHONO2/LINE2 selector switch
This selects the [CH 2] input source from among the devices con-
nected to this unit.
! When set to [PHONO/LINE], the mixer section can be used as a
DJ mixer. In this case, the effect sections of the respective decks
can be used.
8 MIC LEVEL control
Adjusts the audio level input to the [MIC] terminal.
20
En
6
3
2
PHONO2/
TRIM
TRIM
DECK2
LINE2
MASTER
LEVEL
9
9
HI
HI
MIC
LEVEL
9
9
MID
MID
0
EQ
9
9
LOW
LOW
LOW
HI
LEVEL
ON/OFF
MASTER
9
9
MIC
FILTER
FILTER
AUTO MIX
CH1
CH2
10
9
8
7
6
5
4
3
2
1
CROSS F.
0
CURVE
THRU
f
e
7
! Use the [MIC ATT.] control on this unit's rear panel to adjust the
audio level before DJ performances.
9 MIC EQ control
This adjusts the microphone's sound quality.
a MIC (ON/OFF) button
Turns the microphone on/off.
8
b FILTER control
— Turn clockwise to apply the high pass filter.
— Turn counterclockwise to apply the low pass filter.
9
= Using the filter function (p.21)
c AUTO MIX button
a
This turns the auto mix function on and off.
b
d Channel fader
c
Adjusts the level of audio signals output in each channel.
e CROSS F. CURVE (THRU,
selector switch)
d
This switches the crossfader curve characteristics.
f Crossfader
The sound of the respective channels is output according to the
curve characteristics selected with the [THRU,
switch.
(CH2) button
g
The sound of [CH 2] is monitored.
(CH1) button
h
The sound of [CH 1] is monitored.
i HEADPHONES LEVEL control
Adjusts the audio level output from the [PHONES] terminal.
j HEADPHONES MIXING control
Adjusts the balance of the monitor volume between the sound of the
deck whose [
Adjusting the sound quality
Turn the [HI], [MID], [LOW] controls for the respective
channels.
! The sound for that range can be turned completely off by turning the
control all the way counterclockwise (isolator function).
Monitoring sound with headphones
1 Connect headphones to the [PHONES] terminal.
For instructions on connections, see Connecting the input/output termi-
nals on page 10.
2 Press the [
Select the channel you want to monitor.
! This operation is not necessary to monitor the sound output from the
[MASTER OUT 1] and [MASTER OUT 2] terminals (the sound of the
master channel).
3 Turn the [HEADPHONES MIXING] control.
— When turned counterclockwise: The volume of [CH 1] and [CH 2]
becomes relatively louder.
— At the center position: The volume of the [CH 1] and [CH 2]
sound is the same as the volume of the sound output from the
[MASTER OUT 1] and [MASTER OUT 2] terminals (the sound of
the master channel).
,
) (crossfader curve
] button is pressed and the master sound.
(CH1)] or [
(CH2)] button.
,
] selector