Advertisement
READ THE INSTRUCTION INSIDE CAREFULLY.
KEEP THIS USER MANUAL FOR FUTURE
REFERENCE.
For future reference, record the serial
number of your colour monitor.
The serial number is located on the rear of
the monitor.
This monitor is Energy Star compliant when used
with a computer equipped with VESA DPMS,:
The Energy Star emblem does not represent EPA
endorsement of any product or service.
Advertisement
Related Manuals for Hitachi CM2111M
Summary of Contents for Hitachi CM2111M
- Page 1 HITACHI COLOUR MONITOR CM2111M CM-2112M USER MANUAL BEDIENUNGSANLNTUNG MANUAL DE USUARiO GEBRUIKSAANWIJZING MANUEL UTILISATEUR READ THE INSTRUCTION INSIDE CAREFULLY. KEEP THIS USER MANUAL FOR FUTURE REFERENCE. For future reference, record the serial number of your colour monitor. SERIAL No. EPA POLLUTION PREVENTER...
- Page 2 s-I--- c-<-- _ L i------ L.--A -----...
- Page 3 USER MANUAL ’ IL BEDIENUNGSANLEITUNG 1 9 3 5 i MANUAL DE USUARIO GEBRUIKSAANWIJZING 5 MANUEL UTILISATEUR...
- Page 5 . . -‘, ‘, .’ ;/,:. ‘, ,-z.‘,, .~,‘ ,z; ,:, ,,...
-
Page 7: Table Of Contents
MANUAL NOTE : The information in this manual is subject to change without notice. HITACHI assumes no responsibility for any errors that may appear in this manual. FEATURES ............ -
Page 8: Features
The following features are provided by the HITACHI Colour Monitor. Sharpest Focus and Highest Contrast Flat screen CRT with anti-glare, dynamic focus circuit, dark glass, and an INVAR shadow mask gives the sharpest focus and highest contrast to minimize eye fatigue. -
Page 9: Cautions
‘F . A NEVER REMOVE THE REAR COVER ! The rear cover MUST be removed only by authorized service personnel. This colour monitor contains high voltage components. A BE CAREFUL OF STATIC ELECTRICITY ON CRT SURFACE ! To prevent electrical shock by the static electricity on the CRT surface, disconnect the power cord at least 30 SECONDS AFTER turning off the power. -
Page 10: Installation
Install the monitor in the following way, taking care to maintain safety. 1. Installation Install the monitor on a horizontal base. Front Cover , CRT Surface , Power Switch Control Panel A * Tilt & Swivel Base FRONTVIEW Rear Cover Rear Panel AC Inlet Signal Input... - Page 11 A INSTALL THE UNIT IN AN ADEQUATE ENVIRONMENT ! DO NOT expose this monitor to rain or moisture to prevent electric shock or fire hazard. This unit is designed to be used in an office or business environment. DO NOT subject the unit to vibrations, dust, or corrosive gases. A KEEP IN A WELL VENTILATED PLACE ! DO NOT cover this monitor or place anything against any sides (not only the top, right and left side but also the rear and bottom side) of unit.
- Page 12 - Lb FOR THE CUSTOMERS IN U.K. THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U.K. PLEASE REFER TO THE NOTES ON THIS PAGE. IMPORTANT FOR UNITED KINGDOM WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND LABELS The mains lead on this equipment is supplied with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug.
- Page 13 3. Signal Cable Connection 0 For model CM21 12M, use a signal cable with a 13W3 Type D-Sub connector. 13W3Type D-Sub connectorTerminal TABLE l-l Insert connector to the “Signal Input Terminal” (13W3 Type D-Sub Connector Terminal), and secure the screws on the connector shell firmly. 0 For model CM21 11 M, use a signal cable with a D-Sub Mini 15-pin Connector.
- Page 14 4. Power On Turn on the Power Switch of the monitor first, then the computer. NOTICE : 1. After turning OFF the switch, wait at least 5 seconds to restart the monitor. Otherwise the monitor may operate unusually. 2. If the picture doesn’t appear, turn OFF the power switch, make sure of the following and wait at least 30 seconds to restart the monitor.
-
Page 15: Standard Settings
icroprocessor- can store 31 sets of geometry settings including the standard settings. The following industrial standard settings have been preprogrammed by the factory. NOTE : 1. Input signals with approximately the same frequencies may be regarded as the same signal. 2. - Page 16 Power Switch *..-., l---l F-l- Control Panel L .-.-. J-J iADJUSTMENT STORE f ; D E G A U S S I N G L .-.-.-.-.-. COLOUR SELECT MOIRE REDUCTION ._._.-.-.-. ti ON/OFF COLOUR ADJUSTMENT 0 If two or more buttons are pressed at the same time, they will be invalid except when mentioned in the following cases: POWER ON/OFF Press the switch IO I,...
- Page 17 ADJUSTMENT Contrast 0 Press the button 10 1. ,........0 The EasyMenu will showthe Y-f* input signal information with the contrast adjustment condition. ! 0 P r e s s t h e b u t t o n [ - ] o r [ + ] . 8OkHz/ 75Hz .
-
Page 18: Operation
- Trapezoid To activate the Trapezoid control function, ........pressthebuttons[CDland[EI] simultaneously. TRAPEZOID ‘2qfg D+U ; Press the button [ -1 or [+I......[ + ] expands the top side and shrinks the bottom side. [ - ] shrinks the top side and expands the bottom side. To activate the Rotation control function, Rotation “.....,.....~... - Page 19 COLOUR ADJUSTMENT o Select the colour to adjust, by pressing the following buttons. [ :. I and [B ] simultaneously, select the Red colour. [ :. ] and [ 8 ] simultaneously, select the Green colour. [ :. j and [ 0 ] simultaneously, select the Blue colour. El If the LEDs [ :.
- Page 20 4 SToRE Sr O RE Press the button I, to store the currently STORE adjusted data for the following items : @ For the following items, only one setting is allowed : Rotation, Parallelogram Colour (Red, Green and Blue) It is stored to the user colour balance No.3. _..
- Page 21 AUTOMATIC 0 When the monitor has detected a change in the signal input condition, the monitor will - SIGNAL CHECK indicate the condition automatically, as follows : 0 When the monitor detects a valid siqnal, .......a..- the EasyMenu will indicate the horizontal frequency and vertical frequency.
-
Page 22: Power Saving System
0 This monitor complies with VESA, Nutek, and Energy Star power saving requirements. The power saving system works only when used with VESA DPMS compliant PC’s and/or graphic controllers. POWER SAVING STATES 0 This monitor complies with VESA DDCl/ZB specifications. Plug & Play is a system with computer, peripherals (including monitors), and operating system. -
Page 23: Specifications
21 inches diagonal, 0.26 mm (horizontal : 0.21 mm) mask pitch, lnvar shadow mask, Black matrix, Short persistence phosphors. CMZlllME CM21 12MET New Anti- Anti-Reflection Reflection coat panel Video : 0.7 Vp-p, Analog Input Signal Sync. : Separate H, V or Composite H/V TTL level or Sync.