Page 1 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Cisco MDS 9000 Family Command Reference, Release 4.x Cisco MDS NX-OS Release 4.1(3)
Page 2 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Page 3 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C O N T E N T S New and Changed Information xxxiii...
Page 4: Table Of Contents
Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Entering CLI Commands 1-16 Viewing Switch Configurations...
Page 5 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Deleting Files 1-35 Displaying File Contents...
Page 6 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m action reload 2-20 action snmp-trap...
Page 7 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m channel mode active 4-21 channel-group...
Page 8 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear ipv6 access-list 4-60 clear ipv6 neighbors...
Page 9 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear zone 4-97 cli alias name...
Page 10 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m crypto transform-set domain ipsec 4-149 customer-id...
Page 11 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m dpvm commit 5-48 dpvm database...
Page 12 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug fcs 6-45 debug fcsp-mgr...
Page 13 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug rdl errors 6-98 debug rib...
Page 14 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m event manager applet 7-14 event manager policy...
Page 15 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcroute 8-42 fcrxbbcredit extended enable...
Page 16 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fspf retransmit-interval 8-89 G Commands...
Page 17 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ip access-list 11-43 ip address (FCIP profile configuration submode)
Page 18 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m iscsi initiator idle-timeout 11-90 iscsi initiator ip-address...
Page 19 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr vsan-topology 11-138 ivr vsan-topology database...
Page 20 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m M Commands 15-1 C H A P T E R...
Page 21 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m out-of-service xbar 17-27 P Commands...
Page 22 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m pwwn (fcdomain database configuration submode) 18-47 pwwn (SDV virtual device configuration submode)
Page 23 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m role distribute 20-33 role name...
Page 24 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m shared-keymode 21-32 shutdown...
Page 25 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m suspend 21-78 switch-priority...
Page 26 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m system watchdog 21-129 Show Commands...
Page 27 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m show crypto map domain ipsec 22-50 show crypto sad domain ipsec...
Page 28 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m 22-104 show fc-redirect configs 22-105...
Page 29 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m show ip interface 22-180 show ip route...
Page 30 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m show ivr 22-241 show ivr fcdomain database...
Page 31 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m show running radius 22-334 show radius-server...
Page 32 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m show tacacs-server 22-412 show tech-support...
Page 33 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m tape-write command-id 23-21 target (iSLB initiator configuration)
Page 34 Contents S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m virtual-fcid (SDV virtual device configuration submode) 25-3 vrrp...
Page 35: New And Changed Information
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m New and Changed Information Table 1 summarizes the new and changed commands for Cisco MDS NX-OS Release 4.1(3) and tells...
Page 36 New and Changed Information S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Table 1 New and Changed Commands in the Cisco MDS 9000 Family Command Reference (continued) Feature...
Page 37 New and Changed Information S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Table 1 New and Changed Commands in the Cisco MDS 9000 Family Command Reference (continued) Feature...
Page 38 New and Changed Information S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Table 1 New and Changed Commands in the Cisco MDS 9000 Family Command Reference (continued) Feature...
Page 39 New and Changed Information S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Table 1 New and Changed Commands in the Cisco MDS 9000 Family Command Reference (continued) Feature...
Page 40 New and Changed Information S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Table 1 New and Changed Commands in the Cisco MDS 9000 Family Command Reference (continued) Feature...
Page 41 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Preface This preface describes the audience, organization, and conventions of the Cisco MDS 9000 Family Command Reference.
Page 42: Document Conventions
Preface S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Chapter Title Description...
Page 43: Related Documentation
Preface S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m This document uses the following conventions: Means reader take note.
Page 44: Cisco Fabric Manager
Preface S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Cisco MDS 9100 Series Hardware Installation Guide •...
Page 45: Obtaining Documentation And Submitting A Service Request
Preface S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Installation and Configuration Note Cisco MDS 9000 Family SSM Configuration Note •...
Page 46 Preface S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Cisco MDS 9000 Family SMI-S Programming Reference Guide OL-18886-01, Cisco MDS NX-OS Release 4.x...
Page 47: Cli Overview
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C H A P T E R CLI Overview This chapter prepares you to configure switches from the CLI (command-line interface).
Page 48: About The Switch Prompt
Chapter 1 CLI Overview About the Switch Prompt S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m About the Switch Prompt If you are connected to the console port when the switch boots up, you see the output shown in Example...
Page 49 Chapter 1 CLI Overview About the CLI Command Modes S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m About the CLI Command Modes Switches in the Cisco MDS 9000 Family have two main command modeuser EXEC mode and configuration mode.
Page 50 Chapter 1 CLI Overview Understanding CLI Command Hierarchy S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Understanding CLI Command Hierarchy The CLI commands are organized hierarchically, with commands that perform similar functions grouped under the same level.
Page 51: Exec Mode Options
Chapter 1 CLI Overview Understanding CLI Command Hierarchy S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m EXEC Mode Options When you start a session on the switch, you begin in EXEC mode.
Page 52 Chapter 1 CLI Overview Understanding CLI Command Hierarchy S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m terminal Set terminal line parameters test...
Page 53: Configuration Mode Options
Chapter 1 CLI Overview Understanding CLI Command Hierarchy S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m write Write current configuration zone...
Page 54 Chapter 1 CLI Overview Understanding CLI Command Hierarchy S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcflow Configure fcflow fcid-allocation...
Page 55: Cisco Fabric Switch For Ibm Bladecenter
Chapter 1 CLI Overview Understanding CLI Command Hierarchy S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Configuration Mode Commands for the Cisco Fabric Switch for HP c-Class BladeSystem and the Cisco Fabric Switch for IBM BladeCenter switch# config terminal...
Page 56 Chapter 1 CLI Overview Understanding CLI Command Hierarchy S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m rscn Config commands for RSCN scheduler...
Page 57 Chapter 1 CLI Overview Understanding CLI Command Hierarchy S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Table 1-2 Useful Command Key Description Command...
Page 58 Chapter 1 CLI Overview Understanding CLI Command Hierarchy S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Table 1-3 Submodes Within the Configuration Mode for the Cisco MDS 9000 Family (continued) Submode Name...
Page 59: Navigating Through Cli Commands
Chapter 1 CLI Overview Navigating Through CLI Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m SPAN is only supported on external ports.
Page 60: Using The No And Default Forms Of Commands
Chapter 1 CLI Overview Navigating Through CLI Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Using the no and Default Forms of Commands You can issue the no form of any command to perform the following actions: •...
Page 61 Chapter 1 CLI Overview Navigating Through CLI Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Table 1-5 Port Mapping Between the Cisco MDS 9000 Family and the Cisco Fabric Switch for HP c-Class BladeSystem...
Page 62: Entering Cli Commands
Chapter 1 CLI Overview Navigating Through CLI Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Table 1-6 Port Mapping Between the Cisco MDS 9000 Family and the Cisco Fabric Switch for IBM BladeCenter...
Page 63 Chapter 1 CLI Overview Navigating Through CLI Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m You can also gather specific information on the entire switch configuration by issuing the relevant show commands.
Page 64 Chapter 1 CLI Overview Navigating Through CLI Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Reason: Reset Requested by CLI command reload System version: 4.1(0.151) Service:...
Page 65: Saving A Configuration
Chapter 1 CLI Overview Navigating Through CLI Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The show running interface command is different from the show interface command.
Page 66: Searching And Filtering Cli Output
Chapter 1 CLI Overview Searching and Filtering CLI Output S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Searching and Filtering CLI Output The Cisco MDS NX-OS CLI provides ways of searching through large amounts of command output and filtering output to exclude information you do not need.
Page 67: Multiple Filter Commands
Chapter 1 CLI Overview Searching and Filtering CLI Output S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Multiple Filter Commands Cisco MDS NX-OS supports using multiple filters in the same show command output.
Page 68 Chapter 1 CLI Overview Searching and Filtering CLI Output S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fc4/6 sfpAbsent fc4/7...
Page 69 Chapter 1 CLI Overview Searching and Filtering CLI Output S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m 5 minutes output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec 0 transmit B2B credit remaining fc4/2 is down (SFP not present)
Page 70: Displaying Users
Chapter 1 CLI Overview Searching and Filtering CLI Output S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch# The following show interface brief EXEC command uses multiple filter commands to redirect the output where the administration mode is...
Page 71: Using Traceroute
Chapter 1 CLI Overview Searching and Filtering CLI Output S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Using traceroute The traceroute command prints the routes taken by a specified host or IP address.
Page 72: Clearing Vty Sessions
Chapter 1 CLI Overview Searching and Filtering CLI Output S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Parity: none Modem In: Disable...
Page 73: Setting The Switch's Terminal Width
Chapter 1 CLI Overview Using CLI Variables S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Setting the Switch’s Terminal Width To set the terminal screen width for the current session, use the terminal width command in EXEC mode.
Page 74: User-Defined Cli Persistent Variables
Chapter 1 CLI Overview Using CLI Variables S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Port WWN is 20:01:00:0d:ec:0e:1d:00 Admin port mode is auto, trunk mode is on snmp traps are enabled...
Page 75: System Defined Variables
Chapter 1 CLI Overview Using CLI Variables S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m 0 multicast frames, 0 compressed 0 input errors, 0 frame, 0 overrun 0 fifo 9089 packets output, 1234786 bytes, 0 underruns...
Page 76: Using Command Aliases
Chapter 1 CLI Overview Using Command Aliases S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Using Command Aliases Command alias support has the following characteristics: Command aliases are global for all user sessions.
Page 77: Internal Bootflash:
Chapter 1 CLI Overview Formatting Flash Disks and File Systems S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Figure 1-2 Flash Devices in the Cisco MDS 9000 Supervisor Module Internal...
Page 78: Initializing Bootflash:
Chapter 1 CLI Overview Using the File System S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Initializing bootflash: When a switch is shipped, the init system command is already performed and you do not need to issue it again.
Page 79: Setting The Current Directory
Chapter 1 CLI Overview Using the File System S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Displaying the Current Directory, page 1-33 •...
Page 80: Creating A New Directory
Chapter 1 CLI Overview Using the File System S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m This example shows how to list the files on the default volatile: file system: switch# dir Usage for volatile: filesystem...
Page 81: Copying Files
Chapter 1 CLI Overview Using the File System S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Copying Files The copy command copies a file.
Page 82: Saving Command Output To A File
Chapter 1 CLI Overview Using the File System S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Saving Command Output to a File You can force all screen output to go to a file by appending >...
Page 83: Displaying The Last Line In A File
Chapter 1 CLI Overview Using the File System S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The gunzip command uncompresses (unzips) LZ77 coded files.
Page 84: Setting The Delay Time
Chapter 1 CLI Overview Role-Based CLI S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Port WWN is 20:01:00:05:30:00:48:9e Admin port mode is auto, trunk mode is on vsan is 1...
Page 85: Using Valid Formats And Ranges
Chapter 1 CLI Overview Using Valid Formats and Ranges S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Using Valid Formats and Ranges Do not enter ellipsis ( ...
Page 86: Using Debug Commands
Chapter 1 CLI Overview Using Debug Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Table 1-7 Valid Formats and Ranges (continued) Address...
Page 87: Generating Debug Command Output
Chapter 1 CLI Overview Using Debug Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Using the no debug all command is a convenient way to ensure that you have not accidentally left any debug commands turned on.
Page 88: Enabling Message Logging
Chapter 1 CLI Overview Using Debug Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Be aware that the debugging destination you use affects system overhead.
Page 89: Limiting The Types Of Logging Messages Sent To The Console
Chapter 1 CLI Overview Using Debug Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Limiting the Types of Logging Messages Sent to the Console To limit the types of messages that are logged to the console, use the logging console router configuration command.
Page 90: Logging Messages To A Unix Syslog Server
Chapter 1 CLI Overview Using Debug Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m logging monitor notification Logging Messages to a UNIX Syslog Server To log messages to a syslog server host, use the logging host global configuration command.
Page 91 Chapter 1 CLI Overview Using Debug Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The local7 keyword specifies the logging facility to be used.
Page 92 Chapter 1 CLI Overview Using Debug Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Cisco MDS 9000 Family Command Reference 1-46 OL-18089-01, Cisco MDS NX-OS Release 4.x...
Page 93 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C H A P T E R A Commands The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric...
Page 94: Chapter 2 A Command
Chapter 2 A Commands aaa accounting logsize S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m aaa accounting logsize To set the size of the local accounting log file, use the aaa accounting logsize command to set the size of the local accounting log file.
Page 95: Aaa Accounting Default
Chapter 2 A Commands aaa accounting default S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m aaa accounting default To configure the default accounting method, use the aaa accounting default command.
Page 96: Aaa Authentication Dhchap Default
Chapter 2 A Commands aaa authentication dhchap default S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m aaa authentication dhchap default To configure DHCHAP authentication method, use the aaa authentication dhchap default command in configuration mode.
Page 97: Aaa Authentication Iscsi Default
Chapter 2 A Commands aaa authentication iscsi default S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m aaa authentication iscsi default To configure the iSCSI authentication method, use the aaa authentication iscsi default command in configuration mode.
Page 98: Aaa Authentication Login
Chapter 2 A Commands aaa authentication login S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m aaa authentication login To configure the authentication method for a login, use the aaa authentication login command in configuration mode.
Page 99 Chapter 2 A Commands aaa authentication login S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch(config)# aaa authentication login default none The following example reverts to the local authentication method (default): switch(config)# no aaa authentication login default group TacServer...
Page 100: Aaa Authentication Login Password-Aging Enable
Chapter 2 A Commands aaa authentication login password-aging enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m aaa authentication login password-aging enable To configure password aging notifcation from AAA server , use the aaa authentication login password-aging enable in configuration mode.
Page 101: Aaa Group Server
Chapter 2 A Commands aaa group server S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m aaa group server To configure one or more independent server groups, use the aaa group server command in configuration mode.
Page 102 Chapter 2 A Commands aaa group server S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 103: Abort
Chapter 2 A Commands abort S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m abort To discard a Call Home configuration session in progress, use the abort command in Call Home configuration submode.
Page 104: Action Cli
Chapter 2 A Commands action cli S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m action cli To configure a VSH command string to be executed when an Embedded Event Manager (EEM) applet is triggered, use the action cli command.
Page 105: Action Counter
Chapter 2 A Commands action counter S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m action counter To specify setting or modifying a named counter when an Embedded Event Manager (EEM) applet is triggered, use the action counter command.
Page 106 Chapter 2 A Commands action counter S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 107: Action Event-Default
Chapter 2 A Commands action event-default S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m action event-default To execute the default action for the associated event, use the action event-default command.
Page 108: Action Exception Log
Chapter 2 A Commands action exception log S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m action exception log To log an exception if the specific conditions are encountered when an Embedded Event Manager (EEM) applet is triggered, use the action exception log command.
Page 109: Action Forceshut
Chapter 2 A Commands action forceshut S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m action forceshut To configure a forced shutdown of a module, a crossbar, ASCII or the entire switch when an Embedded Event Manager (EEM) applet is triggered, use the action forceshut command.
Page 110: Action Overbudgetshut
Chapter 2 A Commands action overbudgetshut S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m action overbudgetshut To configure the shutdown of a module or the entire switch due to an overbudget power condition when an Embedded Event Manager (EEM) applet is triggered, use the action overbudgetshut command.
Page 111: Action Policy-Default
Chapter 2 A Commands action policy-default S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m action policy-default To enable the default action(s) of the policy being overridden, use the action policy-default command.
Page 112: Action Reload
Chapter 2 A Commands action reload S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m action reload To configure the reloading or to reload the switch software when an Embedded Event Manager (EEM) applet is triggered, use the action reload command.
Page 113: Action Snmp-Trap
Chapter 2 A Commands action snmp-trap S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m action snmp-trap To specify the generation of a Simple Network Management Protocol (SNMP) trap when an Embedded Event Manager (EEM) applet is triggered, use the action snmp-trap command.
Page 114: Action Syslog
Chapter 2 A Commands action syslog S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m action syslog To configure a syslog message to generate when an Embedded Event Manager (EEM) applet is triggered, use the action syslog command.
Page 115 Chapter 2 A Commands action syslog S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command History Release Modification...
Page 116: Active Equals Saved
Chapter 2 A Commands active equals saved S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m active equals saved To automatically write any changes to the block, prohibit or port address name to the IPL file, use the active equals saved command.
Page 117: Alert-Group
Chapter 2 A Commands alert-group S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m alert-group To customize a Call Home alert group with user-defined show commands, use the alert-group command in Call Home configuration submode.
Page 118 Chapter 2 A Commands alert-group S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example removes a user-defined command, called show license usage, for an alert group license.
Page 119 Chapter 2 A Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m To enable the Address Resolution Protocol (ARP) for the switch, use the arp command.
Page 120: Attach
Chapter 2 A Commands attach S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m attach To connect to a specific module, use the attach command in EXEC mode.
Page 121: Attachpriv
Chapter 2 A Commands attachpriv S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m attachpriv To connect to a specific ILC linecard as a privilege, use the attach module command in EXEC mode.
Page 122: Attributes (Dmm Job Configuration Submode)
Chapter 2 A Commands attributes (DMM job configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m attributes (DMM job configuration submode) To set the attributes of a data migration job, use the attributes command in DMM job configuration submode.
Page 123: Attribute Failover Auto
Chapter 2 A Commands attribute failover auto S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m attribute failover auto To configure an automatic fallback failover for a virtual device, use the attribute failover auto fallback command.
Page 124: Attribute Qos
Chapter 2 A Commands attribute qos S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m attribute qos To configure a QoS attribute, use the attribute qos command in Inter-VSAN Routing (IVR) zone configuration submode.
Page 125: Authentication
Chapter 2 A Commands authentication S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m authentication To configure the authentication method for an IKE protocol policy, use the authentication command in IKE policy configuration submode.
Page 126 Chapter 2 A Commands authentication S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 127: Autonomous-Fabric-Id (Ivr Topology Database Configuration)
Chapter 2 A Commands autonomous-fabric-id (IVR topology database configuration) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m autonomous-fabric-id (IVR topology database configuration) To configure an autonomous fabric ID (AFID) into the Inter-VSAN Routing (IVR) topology database, use the autonomous-fabric-id command.
Page 128 Chapter 2 A Commands autonomous-fabric-id (IVR topology database configuration) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The autonomous fabric ID (AFID), which distinguishes two VSANs that are logically and physically •...
Page 129: Autonomous-Fabric-Id (Ivr Service Group Configuration)
Chapter 2 A Commands autonomous-fabric-id (IVR service group configuration) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m autonomous-fabric-id (IVR service group configuration) To configure an autonomous fabric ID (AFID) into an IVR service group, use the autonomous-fabric-id command in IVR service group configuration submode.
Page 130 Chapter 2 A Commands autonomous-fabric-id (IVR service group configuration) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 131: Autonomous-Fabric-Id Database
Chapter 2 A Commands autonomous-fabric-id database S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m autonomous-fabric-id database To configure an autonomous fabric ID (AFID) database, use the autonomous-fabric-id database command.
Page 132: Auto-Volgrp
Chapter 2 A Commands auto-volgrp S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m auto-volgrp To configure the automatic volume grouping, use the auto-volgrp command.
Page 133 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C H A P T E R B Commands The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric...
Page 134: Chapter 3 B Command
Chapter 3 B Commands banner motd S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m banner motd To configure a message of the day (MOTD) banner, use the banner motd command in configuration mode.
Page 135: Banner Motd
Chapter 3 B Commands banner motd S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch(config)# banner motd # Enter TEXT message.
Page 136 Chapter 3 B Commands boot S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m boot To perform operations on the system, use the boot command in configuration mode.
Page 137: Boot
Chapter 3 B Commands boot S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m When the boot auto-copy command is issued, the system copies the boot variable images that are local (present) in the active supervisor module (but not in the standby supervisor module) to the standby supervisor module.
Page 138 Chapter 3 B Commands bport S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m bport To configure a B port mode on a FCIP interface, use the bport option.
Page 139: Bport
Chapter 3 B Commands bport-keepalive S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m bport-keepalive To configure keepalive responses for B port FCIP interfaces, use the bport-keepalive option.
Page 140: Broadcast
Chapter 3 B Commands broadcast S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m broadcast To enable the broadcast frames attribute in a zone attribute group, use the broadcast command.
Page 141 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C H A P T E R C Commands The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric...
Page 142: Chapter 4 C Command
Chapter 4 C Commands callhome S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m callhome To configure the Call Home function, use the callhome command.
Page 143 Chapter 4 C Commands callhome S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch# config terminal config terminal switch# snmp-server contact personname@companyname.com...
Page 144: Callhome Test
Chapter 4 C Commands callhome test S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m callhome test To simulate a Call Home message generation, use the callhome test command.
Page 145 Chapter 4 C Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m To change the default directory or file system, use the cd command.
Page 146 Chapter 4 C Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m To globally configure the Cisco Discovery Protocol parameters, Use the cdp command .
Page 147 Chapter 4 C Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example enables (default) the CDP protocol on the switch.
Page 148: Cfs Distribute
Chapter 4 C Commands cfs distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m cfs distribute To enable or disable Cisco Fabric Services (CFS) distribution on the switch, use the cfs distribute command in configuration mode.
Page 149 Chapter 4 C Commands cfs distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 150: Cfs Ipv4 Distribute
Chapter 4 C Commands cfs ipv4 distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m cfs ipv4 distribute To enable Cisco Fabric Services (CFS) distribution over IPv4 for applications that want to use this feature, use the cfs ipv4 command in configuration mode.
Page 151 Chapter 4 C Commands cfs ipv4 distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Enter configuration commands, one per line.
Page 152: Cfs Ipv4 Mcast-Address
Chapter 4 C Commands cfs ipv4 mcast-address S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m cfs ipv4 mcast-address To configure an IPv4 multicast address for Cisco Fabric Services (CFS) distribution over IPv4, use the cfs ipv4 mcast-address command in configuration mode.
Page 153 Chapter 4 C Commands cfs ipv4 mcast-address S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Change multicast address for CFS-IP ? Are you sure? (y/n) [n] y Related Commands...
Page 154: Cfs Ipv6 Distribute
Chapter 4 C Commands cfs ipv6 distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m cfs ipv6 distribute To enable Cisco Fabric Services (CFS) distribution over IPv6 for applications that want to use this feature, use the cfs ipv6 distribute command in configuration mode.
Page 155 Chapter 4 C Commands cfs ipv6 distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Enter configuration commands, one per line.
Page 156: Cfs Ipv6 Mcast-Address
Chapter 4 C Commands cfs ipv6 mcast-address S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m cfs ipv6 mcast-address To configure an IPv6 multicast address for Cisco Fabric Services (CFS) distribution over IPv6, use the cfs ipv6 mcast-address command in configuration mode.
Page 157 Chapter 4 C Commands cfs ipv6 mcast-address S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Change multicast address for CFS-IP ? Are you sure? (y/n) [n] y Related Commands...
Page 158: Cfs Region
Chapter 4 C Commands cfs region S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m cfs region To create a region that restricts the scope of application distribution to the selected switches, use the cfs region command in the configuration mode.
Page 159 Chapter 4 C Commands cfs region S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch# config Enter configuration commands, one per line.
Page 160: Cfs Static-Peers
Chapter 4 C Commands cfs static-peers S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m cfs static-peers To enable static peers interface, use the cfs static-peers command.
Page 161: Channel Mode Active
Chapter 4 C Commands channel mode active S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m channel mode active To enable channel mode on a PortChannel interface, use the channel mode active command.
Page 162: Channel-Group
Chapter 4 C Commands channel-group S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m channel-group To add a port to a PortChannel group, use the channel-group command.
Page 163: Cimserver
Chapter 4 C Commands cimserver S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m cimserver To configure the Common Information Models (CIM) parameters, Use the cimserver command.
Page 164 Chapter 4 C Commands cimserver S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Examples The following example installs a Secure Socket Layer (SSL) certificate specified in the file named with a .pem extension:...
Page 165: Cimserver Clearcertificate
Chapter 4 C Commands cimserver clearcertificate S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m cimserver clearcertificate To clear the cimserver certificate, use the cimsever clearcertificate command in configuration mode.
Page 166: Cimserver Loglevel
Chapter 4 C Commands cimserver loglevel S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m cimserver loglevel To configure the cimserver loglevel filter, use the cimsever loglevel command in configuration mode.
Page 167: Class
Chapter 4 C Commands class S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m class To select a QoS policy map class for configuration, use the class command in QoS policy map configuration submode.
Page 168 Chapter 4 C Commands class S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command Description priority...
Page 169: Clear Accounting Log
Chapter 4 C Commands clear accounting log S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear accounting log To clear the accounting log, use the clear accounting log command.
Page 170: Clear Arp-Cache
Chapter 4 C Commands clear arp-cache S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear arp-cache To clear the ARP cache table entries, use the clear arp-cache command in EXEC mode.
Page 171: Clear Asic-Cnt
Chapter 4 C Commands clear asic-cnt S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear asic-cnt To clear ASCI counters, use the clear asic-cnt command in EXEC mode.
Page 172 Chapter 4 C Commands clear asic-cnt S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example shows how to list all device IDs: module-4# clear asic-cnt list-all-devices Asic Name...
Page 173: Clear Callhome Session
Chapter 4 C Commands clear callhome session S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear callhome session To clear Call Home Cisco Fabric Services (CFS) session configuration and locks, use the clear callhome session command.
Page 174: Clear Cdp
Chapter 4 C Commands clear cdp S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear cdp To delete global or interface-specific CDP configurations, use the clear cdp command.
Page 175: Clear Cores
Chapter 4 C Commands clear cores S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear cores To clear all core dumps for the switch, use the clear cores command in EXEC mode.
Page 176: Clear Counters (Exec Mode)
Chapter 4 C Commands clear counters (EXEC mode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear counters (EXEC mode) To clear the interface counters, use the clear counters command in EXEC mode.
Page 177: Clear Counters (San Extension N Port Configuration Mode)
Chapter 4 C Commands clear counters (SAN extension N port configuration mode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear counters (SAN extension N port configuration mode) To clear SAN extension tuner N port counters, use the clear counters command.
Page 178: Clear Crypto Ike Domain Ipsec Sa
Chapter 4 C Commands clear crypto ike domain ipsec sa S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear crypto ike domain ipsec sa To clear the IKE tunnels for IPsec, use the clear crypto ike domain ipsec sa command.
Page 179: Clear Crypto Sa Domain Ipsec
Chapter 4 C Commands clear crypto sa domain ipsec S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear crypto sa domain ipsec To clear the security associations for IPsec, use the clear crypto sa domain ipsec command.
Page 180: Clear Debug-Logfile
Chapter 4 C Commands clear debug-logfile S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear debug-logfile To delete the debug log file, use the clear debug-logfile command in EXEC mode.
Page 181: Clear Device-Alias
Chapter 4 C Commands clear device-alias S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear device-alias To clear device alias information, use the clear device-alias command.
Page 182: Clear Dpvm
Chapter 4 C Commands clear dpvm S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear dpvm To clear Dynamic Port VSAN Membership (DPVM) information, use the clear dpvm command.
Page 183: Clear Dpvm Merge Statistics
Chapter 4 C Commands clear dpvm merge statistics S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear dpvm merge statistics To clear the DPVM merge statistics, use the clear dpvm merge statistics command.
Page 184: Clear Fabric-Binding Statistics
Chapter 4 C Commands clear fabric-binding statistics S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear fabric-binding statistics To clear fabric binding statistics in a FICON enabled VSAN, use the clear fabric-binding statistics command in EXEC mode.
Page 185: Clear Fcanalyzer
Chapter 4 C Commands clear fcanalyzer S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear fcanalyzer To clear the entire list of configured hosts for remote capture, use the clear fcanalyzer command in EXEC mode.
Page 186: Clear Fcflow Stats
Chapter 4 C Commands clear fcflow stats S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear fcflow stats To clear Fibre Channel flow statistics, use the clear fcflow stats command in EXEC mode.
Page 187: Clear Fcns Statistics
Chapter 4 C Commands clear fcns statistics S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear fcns statistics To clear the name server statistics, use the clear fcns statistics command in EXEC mode.
Page 188: Clear Fcs Statistics
Chapter 4 C Commands clear fcs statistics S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear fcs statistics To clear the fabric configuration server statistics, use the clear fcs statistics command in EXEC mode.
Page 189: Clear Fctimer Session
Chapter 4 C Commands clear fctimer session S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear fctimer session To clear fctimer Cisco Fabric Services (CFS) session configuration and locks, use the clear fctimer session command.
Page 190: Clear Fc-Redirect Config
Chapter 4 C Commands clear fc-redirect config S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear fc-redirect config To delete a FC-Redirect configuration on a switch, use the clear fc-redirect config command.
Page 191: Clear Fc-Redirect Decommission-Switch
Chapter 4 C Commands clear fc-redirect decommission-switch S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear fc-redirect decommission-switch To remove all existing FC-Redirect configurations and disable any further FC-Redirect configurations on a switch, use the clear fc-redirect decommission-switch command.
Page 192 Chapter 4 C Commands clear fc-redirect decommission-switch S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 193: Clear Ficon
Chapter 4 C Commands clear ficon S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear ficon Use the clear ficon command in EXEC mode to clear the FICON information for the specified VSAN.
Page 194: Clear Fspf Counters
Chapter 4 C Commands clear fspf counters S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear fspf counters To clear the Fabric Shortest Path First statistics, use the clear fspf counters command in EXEC mode.
Page 195: Clear Install Failure-Reason
Chapter 4 C Commands clear install failure-reason S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear install failure-reason To remove the upgrade failure reason log created during in-service software upgrades (ISSUs) on the Cisco MDS 9124 Fabric Switch, use the clear install failure-reason command.
Page 196: Clear Ip Access-List Counters
Chapter 4 C Commands clear ip access-list counters S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear ip access-list counters To clear IP access list counters, use the clear ip access-list counters command in EXEC mode.
Page 197: Clear Ips Arp
Chapter 4 C Commands clear ips arp S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear ips arp To clear ARP caches, use the clear ips arp command in EXEC mode.
Page 198: Clear Ips Stats
Chapter 4 C Commands clear ips stats S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear ips stats To clear IP storage statistics, use the clear ips stats command in EXEC mode.
Page 199: Clear Ips Stats Fabric Interface
Chapter 4 C Commands clear ips stats fabric interface S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear ips stats fabric interface To clear the statistics for a given iSCSI or FCIP interface on a Cisco MDS 9000 18/4-Port Multi Service Module IPS linecard, use the clear ips stats fabric interface command.
Page 200: Clear Ipv6 Access-List
Chapter 4 C Commands clear ipv6 access-list S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear ipv6 access-list To clear IPv6 access control list statistics, use the clear ipv6 access-list command.
Page 201: Clear Ipv6 Neighbors
Chapter 4 C Commands clear ipv6 neighbors S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear ipv6 neighbors To clear the IPv6 neighbor cache table, use the clear ipv6 neighbors command.
Page 202: Clear Islb Session
Chapter 4 C Commands clear islb session S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear islb session To clear a pending iSLB configuration, use the clear islb session command.
Page 203: Clear Ivr Fcdomain Database
Chapter 4 C Commands clear ivr fcdomain database S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear ivr fcdomain database To clear the IVR fcdomain database, use the clear ivr fcdomain database command in EXEC mode.
Page 204: Clear Ivr Service-Group Database
Chapter 4 C Commands clear ivr service-group database S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear ivr service-group database To clear an inter-VSAN routing (IVR) service group database, use the clear ivr service-group database command.
Page 205: Clear Ivr Zone Database
Chapter 4 C Commands clear ivr zone database S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear ivr zone database To clear the Inter-VSAN Routing (IVR) zone database, use the clear ivr zone database command in EXEC mode.
Page 206: Clear License
Chapter 4 C Commands clear license S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear license To uninstall a license, use the clear license command in EXEC mode.
Page 207: Clear Line
Chapter 4 C Commands clear line S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear line To clear VTY sessions, use the clear line command in EXEC mode.
Page 208: Clear Logging
Chapter 4 C Commands clear logging S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear logging To delete the syslog information, use the clear logging command in EXEC mode.
Page 209: Clear Ntp
Chapter 4 C Commands clear ntp S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear ntp To clear Network Time Protocol (NTP) information, use the clear ntp command in EXEC mode.
Page 210: Clear Port-Security
Chapter 4 C Commands clear port-security S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear port-security To clear the port security information on the switch, use the clear port-security command in EXEC mode.
Page 211 Chapter 4 C Commands clear port-security S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 212: Clear Processes Log
Chapter 4 C Commands clear processes log S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear processes log To clear the log files on the switch, use the clear processes log command in EXEC mode.
Page 213: Clear Qos Statistics
Chapter 4 C Commands clear qos statistics S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear qos statistics To clear the quality of services statistics counters, use the clear qos statistics command in EXEC mode.
Page 214: Clear Radius Session
Chapter 4 C Commands clear radius session S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear radius session To clear RADIUS Cisco Fabric Services (CFS) session configuration and locks, use the clear radius session command.
Page 215: Clear Rlir
Chapter 4 C Commands clear rlir S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear rlir To clear the Registered Link Incident Report (RLIR), use the clear rlir command in EXEC mode.
Page 216 Chapter 4 C Commands clear rlir S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example clears recent RLIR information for a specified port number: switch# clear rlir recent portnumber 16 Related Commands...
Page 217: Clear Rmon Alarms
Chapter 4 C Commands clear rmon alarms S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear rmon alarms To clear all the 32-bit remote monitoring (RMON) alarms from the running configuration, use the clear rmon alarms command.
Page 218: Clear Rmon All-Alarms
Chapter 4 C Commands clear rmon all-alarms S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear rmon all-alarms To clear all the 32-bit and 64-bit RMON alarms from the running configuration, use the clear rmon all-alarms command.
Page 219: Clear Rmon Hcalarms
Chapter 4 C Commands clear rmon hcalarms S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear rmon hcalarms To clear all the 64-bit RMON alarms from the running configuration, use the clear rmon hcalarms command.
Page 220: Clear Rmon Log
Chapter 4 C Commands clear rmon log S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear rmon log To clear all entries from RMON log on the switch, use the clear rmon log command.
Page 221: Clear Role Session
Chapter 4 C Commands clear role session S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear role session To clear authentication role Cisco Fabric Services (CFS) session configuration and locks, use the clear role session command.
Page 222: Clear Rscn Session Vsan
Chapter 4 C Commands clear rscn session vsan S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear rscn session vsan To clear a Registered State Change Notification (RSCN) session for a specified VSAN, use the clear rscn session vsan command.
Page 223: Clear Rscn Statistics
Chapter 4 C Commands clear rscn statistics S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear rscn statistics To clear the registered state change notification statistics for a specified VSAN, use the clear rscn statistics command in EXEC mode.
Page 224: Clear Santap Module
Chapter 4 C Commands clear santap module S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear santap module To clear SANTap information, use the clear santap module command.
Page 225: Clear Ssm-Nvram Santap Module
Chapter 4 C Commands clear ssm-nvram santap module S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear ssm-nvram santap module To clear the SANTap configuration for a specific slot stored on the supervisor flash, use the clear ssm-nvram santap module command in the configuration mode.
Page 226: Clear Scheduler Logfile
Chapter 4 C Commands clear scheduler logfile S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear scheduler logfile To clear the command scheduler logfile, use the clear scheduler logfile command.
Page 227: Clear Screen
Chapter 4 C Commands clear screen S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear screen To clear the terminal screen, use the clear screen command in EXEC mode.
Page 228: Clear Scsi-Flow Statistics
Chapter 4 C Commands clear scsi-flow statistics S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear scsi-flow statistics To clear the SCSI flow statistics counters, use the clear scsi-flow statistics command.
Page 229: Clear Sdv
Chapter 4 C Commands clear sdv S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear sdv To clear specified SAN device virtualization parameters, use the clear sdv command in EXEC mode.
Page 230: Clear Snmp Hostconfig
Chapter 4 C Commands clear snmp hostconfig S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear snmp hostconfig To clear all SNMP hosts from the running configuration, use the clear snmp hostconfig command.
Page 231: Clear Ssh Hosts
Chapter 4 C Commands clear ssh hosts S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear ssh hosts To clear trusted SSH hosts, use the clear ssh hosts command in EXEC mode.
Page 232: Clear System Reset-Reason
Chapter 4 C Commands clear system reset-reason S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear system reset-reason To clear the reset-reason information stored in NVRAM and volatile persistent storage, use the clear system reset-reason command in EXEC mode.
Page 233: Clear Tacacs+ Session
Chapter 4 C Commands clear tacacs+ session S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear tacacs+ session To clear TACACS+ Cisco Fabric Services (CFS) session configuration and locks, use the clear tacacs+ session command.
Page 234: Clear Tlport Alpa-Cache
Chapter 4 C Commands clear tlport alpa-cache S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear tlport alpa-cache To clear the entire contents of the alpa-cache, use the clear tlport alpa-cache command in EXEC mode.
Page 235: Clear User
Chapter 4 C Commands clear user S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear user To clear trusted SSH hosts, use the clear user command in EXEC mode.
Page 236: Clear Vrrp
Chapter 4 C Commands clear vrrp S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear vrrp To clear all the software counters for the specified virtual router, use the clear vrrp command in EXEC mode.
Page 237: Clear Zone
Chapter 4 C Commands clear zone S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clear zone To clear all configured information in the zone server for a specified VSAN, use the clear zone command in EXEC mode.
Page 238: Cli Alias Name
Chapter 4 C Commands cli alias name S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m cli alias name To define a command alias name, use the cli alias name command in configuration submode.
Page 239 Chapter 4 C Commands cli alias name S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Examples The following example shows how to define command aliases in configuration submode: switch# config t...
Page 240: Cli Var Name (Exec)
Chapter 4 C Commands cli var name (EXEC) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m cli var name (EXEC) To define a CLI session variable that persists only for the duration of a CLI session, use the cli var name command in either EXEC mode or configuration submode.
Page 241 Chapter 4 C Commands cli var name (EXEC) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 242: Cli Var Name (Configuration)
Chapter 4 C Commands cli var name (configuration) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m cli var name (configuration) To define a CLI variable that persists across CLI sessions and switch reloads, use the cli var name command in configuration submode.
Page 243: Clock
Chapter 4 C Commands clock S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clock To configure the time zone or daylight savings time, use the clock command in configuration mode.
Page 244 Chapter 4 C Commands clock S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Specify the hours-offset argument with a dash before the number;...
Page 245: Clock Set
Chapter 4 C Commands clock set S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m clock set To change the system time on a Cisco MDS 9000 Family switch, use the clock set command in EXEC mode.
Page 246: Cloud Discover
Chapter 4 C Commands cloud discover S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m cloud discover To initiate manual, on-demand cloud discovery, use the cloud discover command.
Page 247: Cloud Discovery
Chapter 4 C Commands cloud discovery S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m cloud discovery To configure cloud discovery, use the cloud discovery command in configuration mode.
Page 248 Chapter 4 C Commands cloud discovery S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 249: Cloud-Discovery Enable
Chapter 4 C Commands cloud-discovery enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m cloud-discovery enable To enable discovery of cloud memberships, use the cloud-discovery command in configuration mode.
Page 250: Cluster
Chapter 4 C Commands cluster S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m cluster To configure a cluster feature, use the cluster command.
Page 251: Code-Page
Chapter 4 C Commands code-page S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m code-page Use the code-page command to configure the EBCDIC format.
Page 252 Chapter 4 C Commands code-page S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 253: Commit
Chapter 4 C Commands commit S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m commit To apply the pending configuration pertaining to the Call Home configuration session in progress, use the commit command in Call Home configuration submode.
Page 254: Commit (Dmm Job Configuration Submode)
Chapter 4 C Commands commit (DMM job configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m commit (DMM job configuration submode) To commit a DMM job, use the commit command in DMM job configuration submode.
Page 255: Contract-Id
Chapter 4 C Commands contract-id S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m contract-id To configure the service contract ID of the customer with the Call Home function, use the contract-id command in Call Home configuration submode.
Page 256: Configure Terminal
Chapter 4 C Commands configure terminal S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m configure terminal To enter the configuration mode, use the configure terminal command in EXEC mode.
Page 257: Copy
Chapter 4 C Commands copy S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m copy To save a backup of the system software, use the copy command in EXEC mode.
Page 258 Chapter 4 C Commands copy S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Defaults None.
Page 259 Chapter 4 C Commands copy S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch# copy samplefile mystorage/samplefile If the current directory is slot0:mydir, this command copies slot0:mydir/samplefile to slot0:mydir/mystorage/samplefile.
Page 260: Copy Licenses
Chapter 4 C Commands copy licenses S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m copy licenses To save a backup of the installed license files, use the copy licenses command in EXEC mode.
Page 261: Copy Ssm-Nvram Standby-Sup
Chapter 4 C Commands copy ssm-nvram standby-sup S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m copy ssm-nvram standby-sup To copy the contents of the Storage Services Module (SSM) NVRAM to the standby Supervisor 2 module when migrating from a Supervisor 1 to Supervisor 2 module, use the copy ssm-nvram...
Page 262: Counter
Chapter 4 C Commands counter S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m counter To configure an indivisual counter to override the default configuration, use the counter command.
Page 263 Chapter 4 C Commands counter S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example shows all the changes made using the port-type and counter commands by using the show port-monitor [name] and the show running config command: switch(config-port-monitor)# do show port-monitor cisco...
Page 264: Crypto Ca Authenticate
Chapter 4 C Commands crypto ca authenticate S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m crypto ca authenticate To associate and authenticate a certificate of the certificate authority (CA) and configure its CA certificate (or certificate chain), use the crypto ca authenticate command in configuration mode.
Page 265 Chapter 4 C Commands crypto ca authenticate S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m To ensure that the configured certificates, CRLs and key pairs are made persistent, always save the running configuration to the startup configuration.
Page 266: Crypto Ca Crl Request
Chapter 4 C Commands crypto ca crl request S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m crypto ca crl request To configure a new certificate revocation list (CRL) downloaded from the certificate authority (CA), use the crypto ca crl request command in configuration mode.
Page 267 Chapter 4 C Commands crypto ca crl request S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Examples The following example configures a CRL for the trust point or replaces the current CRL: switch# config t...
Page 268: Crypto Ca Enroll
Chapter 4 C Commands crypto ca enroll S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m crypto ca enroll To request a certificate for the switch’s RSA key pair created for this trust point CA, use the crypto ca enroll command in configuration mode.
Page 269 Chapter 4 C Commands crypto ca enroll S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The subject name in the certificate will be: Vegas-1.cisco.com Include the switch serial number in the subject name? [yes/no]:no Include an IP address in the subject name [yes/no]:yes...
Page 270: Crypto Ca Export
Chapter 4 C Commands crypto ca export S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m crypto ca export To export the RSA key pair and the associated certificates (identity and CA) of a trust point within a Public-Key Cryptography Standards (PKCS) #12 format file to a specified location, use the crypto ca...
Page 271 Chapter 4 C Commands crypto ca export S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command Description rsakeypair...
Page 272: Crypto Ca Import
Chapter 4 C Commands crypto ca import S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m crypto ca import To import the identity certificate alone in PEM format or the identity certificate and associated RSA key pair and CA certificate (or certificate chain) in Public-Key Cryptography Standards (PKCS) #12 form,...
Page 273 Chapter 4 C Commands crypto ca import S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Examples The following example installs an identity certificate obtained from a CA corresponding to an enrollment request made and submitted earlier:...
Page 274: Crypto Ca Test Verify
Chapter 4 C Commands crypto ca test verify S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m crypto ca test verify To verify a certificate file, use the crypto ca test verify command in configuration mode.
Page 275: Crypto Ca Trustpoint
Chapter 4 C Commands crypto ca trustpoint S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m crypto ca trustpoint To create a trust point certificate authority (CA) that the switch should trust, and enter trust point configuration submode (config-trustpoint), use the crypto ca trustpoint command in configuration...
Page 276 Chapter 4 C Commands crypto ca trustpoint S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Before using the no crypto ca trustpoint command to remove the trust point, first delete the identity Note certificate and CA certificate (or certificate chain) and then disassociate the RSA key pair from the trust...
Page 277: Crypto Global Domain Ipsec Security-Association Lifetime
Chapter 4 C Commands crypto global domain ipsec security-association lifetime S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m crypto global domain ipsec security-association lifetime To configure global parameters for IPsec, use the crypto global domain ipsec security-association lifetime command.
Page 278: Crypto Ike Domain Ipsec
Chapter 4 C Commands crypto ike domain ipsec S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m crypto ike domain ipsec To enter IKE configuration submode, use the crypto ike domain ipsec command.
Page 279: Crypto Ike Domain Ipsec Rekey Sa
Chapter 4 C Commands crypto ike domain ipsec rekey sa S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m crypto ike domain ipsec rekey sa To rekey an IKE crypto security association (SA) in the IPsec domain, use the crypto ike domain ipsec rekey sa command.
Page 280: Crypto Ike Enable
Chapter 4 C Commands crypto ike enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m crypto ike enable To enable IKE, use the crypto ike enable command.
Page 281: Crypto Ipsec Enable
Chapter 4 C Commands crypto ipsec enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m crypto ipsec enable To enable IPsec, use the crypto ipsec enable command.
Page 282: Crypto Key Generate Rsa
Chapter 4 C Commands crypto key generate rsa S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m crypto key generate rsa To generate an RSA key pair, use the crypto key generate rsa command in configuration mode.
Page 283 Chapter 4 C Commands crypto key generate rsa S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 284: Crypto Key Zeroize Rsa
Chapter 4 C Commands crypto key zeroize rsa S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m crypto key zeroize rsa To delete an RSA key pair from the switch, use the crypto key zeroize rsa command in configuration mode.
Page 285 Chapter 4 C Commands crypto key zeroize rsa S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 286: Crypto Map Domain Ipsec (Configuration Mode)
Chapter 4 C Commands crypto map domain ipsec (configuration mode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m crypto map domain ipsec (configuration mode) To specify an IPsec crypto map and enter IPsec crypto map configuration mode, use the crypto map domain ipsec command.
Page 287 Chapter 4 C Commands crypto map domain ipsec (configuration mode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 288: Crypto Map Domain Ipsec (Interface Configuration Submode)
Chapter 4 C Commands crypto map domain ipsec (interface configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m crypto map domain ipsec (interface configuration submode) To configure an IPsec crypto map on a Gigabit Ethernet interface, use the crypto map domain ipsec command in interface configuration submode.
Page 289: Crypto Transform-Set Domain Ipsec
Chapter 4 C Commands crypto transform-set domain ipsec S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m crypto transform-set domain ipsec To create and configure IPsec transform sets, use the crypto transform-set domain ipsec command.
Page 290 Chapter 4 C Commands crypto transform-set domain ipsec S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m You can use this command to modify existing IPsec transform sets.
Page 291: Customer-Id
Chapter 4 C Commands customer-id S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m customer-id To configure the customer ID with the Call Home function, use the customer-id command in Call Home configuration submode.
Page 292 Chapter 4 C Commands customer-id S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Cisco MDS 9000 Family Command Reference 4-152 OL-18089-01, Cisco MDS NX-OS Release 4.x...
Page 293 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C H A P T E R D Commands The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric...
Page 294: Chapter 5 D Command
Chapter 5 D Commands data-pattern-file S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m data-pattern-file To configure data pattern file for a SAN tuner extension N port, use the data-pattern-file command in interface configuration submode.
Page 295: Deadtime (Radius Group Configuration)
Chapter 5 D Commands deadtime (radius group configuration) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m deadtime (radius group configuration) To configure a periodic time interval where a nonreachable (nonresponsive) RADIUS server is monitored for responsiveness, use the deadtime command in RADIUS group configuration submode.
Page 296: Deadtime (Tacacs+ Group Configuration)
Chapter 5 D Commands deadtime (tacacs+ group configuration) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m deadtime (tacacs+ group configuration) To configure a periodic time interval where a nonreachable (nonresponsive) TACACS+ server is monitored for responsiveness, use the deadtime command in TACACS+ group configuration submode.
Page 297 Chapter 5 D Commands delete S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m delete To delete a specified file or directory on a flash memory device, use the delete command in EXEC mode.
Page 298: Delete
Chapter 5 D Commands delete S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch# delete dns_config.cfg The following example deletes a file from an external CompactFlash (slot0): switch# delete slot0:dns_config.cfg...
Page 299: Delete Ca-Certificate
Chapter 5 D Commands delete ca-certificate S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m delete ca-certificate To delete certificate authority certificates, use the delete ca-certificate command in trust point configuration submode.
Page 300: Delete Certificate
Chapter 5 D Commands delete certificate S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m delete certificate To delete the identity certificate, use the delete certificate command in trust point configuration submode.
Page 301: Delete Certificate
Chapter 5 D Commands delete certificate S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 302: Delete Crl
Chapter 5 D Commands delete crl S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m delete crl To delete the crl from the trustpoint, use the delete crl command in trust point configuration submode.
Page 303 Chapter 5 D Commands deny (IPv6-ACL configuration) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m deny (IPv6-ACL configuration) To configure deny conditions for an IPv6 access control list (ACL), use the deny command in IPv6-ACL configuration submode.
Page 304: Deny (Ipv6-Acl Configuration)
Chapter 5 D Commands deny (IPv6-ACL configuration) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m dest-port-operator Specifies an operand that compares the destination ports of the specified protocol.
Page 305 Chapter 5 D Commands deny (IPv6-ACL configuration) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example removes the IPv6-ACL called List1 and all its entries: switch# config terminal switch(config)# no ipv6 access-list List1...
Page 306 Chapter 5 D Commands description S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m description To configure a description for the Event Manager policy, use the description command.
Page 307: Description
Chapter 5 D Commands destination interface S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m destination interface To configure a switched port analyzer (SPAN) destination interface, use the destination interface command in SPAN session configuration submode.
Page 308: Destination Interface
Chapter 5 D Commands destination interface S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 309 Chapter 5 D Commands destination-profile S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m destination-profile To configure the attributes of the destination such as the e-mail address or the message level with the Call Home function, use the destination-profile command in Call Home configuration submode.
Page 310: Destination-Profile
Chapter 5 D Commands destination-profile S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m message-size Configures the maximum message size (default 2500000).
Page 311 Chapter 5 D Commands destination-profile S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 312: Device-Alias (Ivr Fcdomain Database Configuration Submode)
Chapter 5 D Commands device-alias (IVR fcdomain database configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m device-alias (IVR fcdomain database configuration submode) To map a device alias to a persistent FC ID for IVR, use the device-alias command in IVR fcdomain database configuration submode.
Page 313: Device-Alias (Sdv Virtual Device Configuration Submode)
Chapter 5 D Commands device-alias (SDV virtual device configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m device-alias (SDV virtual device configuration submode) To add a device alias to a virtual device, use the device-alias command in SDV virtual device configuration submode.
Page 314: Device-Alias Abort
Chapter 5 D Commands device-alias abort S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m device-alias abort To discard a Distributed Device Alias Services (device alias) Cisco Fabric Services (CFS) distribution session in progress, use the device-alias abort command in configuration mode.
Page 315 Chapter 5 D Commands device-alias commit S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m device-alias commit To apply the pending configuration pertaining to the Distributed Device Alias Services (device alias) Cisco Fabric Services (CFS) distribution session in progress in the fabric, use the device-alias commit...
Page 316: Device-Alias Commit
Chapter 5 D Commands device-alias database S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m device-alias database To initiate a Distributed Device Alias Services (device alias) session and configure device alias database, use the device-alias database command.
Page 317: Device-Alias Database
Chapter 5 D Commands device-alias distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m device-alias distribute To enable Cisco Fabric Services (CFS) distribution for Distributed Device Alias Services (device alias), use the device-alias distribute command.
Page 318: Device-Alias Distribute
Chapter 5 D Commands device-alias import fcalias S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m device-alias import fcalias To import device alias database information from another VSAN, use the device-alias import fcalias command.
Page 319 Chapter 5 D Commands device-alias mode enhanced S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m device-alias mode enhanced To configure device aliases to operate in enhanced mode, use the device-alias mode enhanced command.
Page 320: Device-Alias Mode Enhanced
Chapter 5 D Commands device-alias mode enhanced S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command Description device-alias database...
Page 321: Device-Alias Name
Chapter 5 D Commands device-alias name S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m device-alias name To configure device names in the device alias database, use the device-alias name command.
Page 322 Chapter 5 D Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m To display the contents of the current directory or the specified directory, use the dir command in EXEC mode.
Page 323 Chapter 5 D Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Usage for bootflash://sup-local 135404544 bytes used 49155072 bytes free...
Page 324 Chapter 5 D Commands disable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m disable To disable the Call Home function, use the disable command in Call Home configuration submode.
Page 325: Disable
Chapter 5 D Commands discover S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m discover To initiate the discovery of hosts, use the discovery command.
Page 326: Discover
Chapter 5 D Commands discover custom-list S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m discover custom-list To selectively initiate discovery for specified domain IDs in a VSAN, use the discover custom-list command in EXEC mode.
Page 327 Chapter 5 D Commands discover scsi-target S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m discover scsi-target To discover SCSI targets on local storage to the switch or remote storage across the fabric, use the discover scsi-target command in EXEC mode.
Page 328: Discover Scsi-Target
Chapter 5 D Commands discover scsi-target S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch# discover scsi-target remote os windows discovery started The following example shows how to discover SCSI targets for the specified VSAN (1) and FCID...
Page 329: Distribute
Chapter 5 D Commands distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m distribute To enable distribution of the Call Home function using CFS, use the distribute command in Call Home configuration submode.
Page 330: Dmm Module
Chapter 5 D Commands dmm module S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m dmm module To specify default DMM values for migration block size, number of migration blocks and fast migration speed, use the dmm module command in configuration mode.
Page 331: Dmm Module
Chapter 5 D Commands dmm module S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 332: Dmm Module Job
Chapter 5 D Commands dmm module job S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m dmm module job To configure a data migration job, use the dmm module mod-id job command in configuration mode.
Page 333: Dmm Module Job
Chapter 5 D Commands dmm module job S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command History Release Modification...
Page 334 Chapter 5 D Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Use the do command to execute an EXEC-level command from any configuration mode or submode.
Page 335 Chapter 5 D Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Peer port WWN is 20:42:00:0b:46:79:f1:80 Admin port mode is auto, trunk mode is on Port mode is TE...
Page 336: Dpvm Abort
Chapter 5 D Commands dpvm abort S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m dpvm abort To discard a dynamic port VSAN membership (DPVM) Cisco Fabric Services (CFS) distribution session in progress, use the dpvm abort command in configuration mode.
Page 337: Dpvm Activate
Chapter 5 D Commands dpvm activate S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m dpvm activate To activate the dynamic port VSAN membership (DPVM) configuration database, use the dpvm activate command.
Page 338 Chapter 5 D Commands dpvm auto-learn S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m dpvm auto-learn To enable the automatic learning feature (autolearn) for the active dynamic port VSAN membership (DPVM) database, use the dpvm auto-learn command.
Page 339: Dpvm Auto-Learn
Chapter 5 D Commands dpvm auto-learn S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch# config terminal switch(config)# no dpvm auto-learn Related Commands...
Page 340: Dpvm Commit
Chapter 5 D Commands dpvm commit S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m dpvm commit To apply the pending configuration pertaining to the dynamic port VSAN membership (DPVM) Cisco Fabric Services (CFS) distribution session in progress in the fabric, use the dpvm commit command.
Page 341: Dpvm Database
Chapter 5 D Commands dpvm database S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m dpvm database To activate and configure the dynamic port VSAN membership (DPVM) database, use the dpvm database command.
Page 342: Dpvm Database
Chapter 5 D Commands dpvm database S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 343: Dpvm Database Copy Active
Chapter 5 D Commands dpvm database copy active S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m dpvm database copy active To copy the active dynamic port VSAN membership (DPVM) database to the config DPVM database, use the dpvm database copy active command.
Page 344: Dpvm Database Diff
Chapter 5 D Commands dpvm database diff S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m dpvm database diff To display the active dynamic port VSAN membership (DPVM) database, use the dpvm database diff command.
Page 345: Dpvm Database Diff
Chapter 5 D Commands dpvm database diff S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 346: Dpvm Distribute
Chapter 5 D Commands dpvm distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m dpvm distribute To enable Cisco Fabric Services (CFS) distribution for dynamic port VSAN membership (DPVM), use the dpvm distribute command.
Page 347: Dpvm Enable
Chapter 5 D Commands dpvm enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m dpvm enable To enable dynamic port VSAN membership (DPVM), use to dpvm enable command.
Page 348: Dpvm Overwrite-Duplicate-Pwwn
Chapter 5 D Commands dpvm overwrite-duplicate-pwwn S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m dpvm overwrite-duplicate-pwwn To overwrite the first login information with the duplicate PWWN login, use the dpvm overwrite-duplicate-pwwn command.
Page 349: Dscp
Chapter 5 D Commands dscp S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m dscp To configure a differentiated services code point (DSCP) in a QoS policy map class, use the dscp command in EXEC mode.
Page 350: Duplicate-Message Throttle
Chapter 5 D Commands duplicate-message throttle S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m duplicate-message throttle To enable throttling of duplicate Call Home alert messages, use the duplicate-message throttle command in Call Home configuration submode.
Page 351: Debug Commands
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C H A P T E R Debug Commands The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric...
Page 352: Chapter 6 Debug Command
Chapter 6 Debug Commands debug aaa S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug aaa To enable debugging for boot variables, use the debug aaa command in EXEC mode.
Page 353: Debug Aaa
Chapter 6 Debug Commands debug aaa S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 354: Debug All
Chapter 6 Debug Commands debug all S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug all To enable debugging for all features on the switch, use the debug all command in EXEC mode.
Page 355: Debug All
Chapter 6 Debug Commands debug biosd S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug biosd To configure bios_daemon debugging, use the debug biosd command in EXEC mode.
Page 356: Debug Bootvar
Chapter 6 Debug Commands debug bootvar S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug bootvar To enable debugging for boot variables, use the debug bootvar command in EXEC mode.
Page 357: Debug Callhome
Chapter 6 Debug Commands debug callhome S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug callhome To enable debugging for the Call Home function, use the debug callhome command in EXEC mode.
Page 358: Debug Callhome
Chapter 6 Debug Commands debug callhome S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m 2005 Mar 9 05:37:21 callhome: running cli commands for alert name : Test, message id : 1540383426...
Page 359 Chapter 6 Debug Commands debug cert-enroll S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug cert-enroll To enable debugging for the certificate enroll daemon, use the debug cert-enroll command in EXEC mode.
Page 360: Debug Cert-Enroll
Chapter 6 Debug Commands debug cert-enroll S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 361: Debug Cdp
Chapter 6 Debug Commands debug cdp S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug cdp To enable debugging for the Cisco Discovery Protocol (CDP) function, use the debug cdp command in EXEC mode.
Page 362: Debug Cdp
Chapter 6 Debug Commands debug cdp S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m 8 21:23:35 cdp: Sent CDP packet, interface 0x2382000 Related Commands Command...
Page 363: Debug Cfs
Chapter 6 Debug Commands debug cfs S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug cfs To enable debugging for Cisco Fabric Services (CFS), use the debug cfs command in EXEC mode.
Page 364: Debug Cfs
Chapter 6 Debug Commands debug cfs S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Examples The following example displays the system output when the debug cfs all command is issued: switch# debug cfs all...
Page 365: Debug Cimserver
Chapter 6 Debug Commands debug cimserver S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug cimserver To enable debugging for the Common Information Model (CIM) management applications function, use the debug cimserver command in EXEC mode.
Page 366: Debug Cloud
Chapter 6 Debug Commands debug cloud S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug cloud To enable debugging of cloud discovery, use the debug cloud command in EXEC mode.To disable a debug command, use the no form of the command or use the no debug all command to turn off all...
Page 367: Debug Cloud
Chapter 6 Debug Commands debug cloud S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command History Release Modification...
Page 368: Debug Core
Chapter 6 Debug Commands debug core S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug core To enable core daemon debugging, use the debug core command in EXEC mode.
Page 369 Chapter 6 Debug Commands debug device-alias S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug device-alias To enable debugging for device aliases, use the debug device-alias command in EXEC mode.
Page 370: Debug Device-Alias
Chapter 6 Debug Commands debug device-alias S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 371 Chapter 6 Debug Commands debug dmm-debug S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug dmm-debug To enable debugging for DMM, use the debug dmm-debug command.
Page 372: Debug Dmm-Debug
Chapter 6 Debug Commands debug dmm-debug S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Examples The following example enables all the DMM debug options: switch# debug dmm-debug all...
Page 373: Debug Dpvm
Chapter 6 Debug Commands debug dpvm S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug dpvm To enable debugging for dynamic port VSAN membership (DPVM), use the debug dpvm command in EXEC mode.
Page 374: Debug Dpvm
Chapter 6 Debug Commands debug dpvm S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 375: Debug Dstats
Chapter 6 Debug Commands debug dstats S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug dstats To enable delta statistics debugging, use the debug dstats command in EXEC mode.
Page 376: Debug Ethport
Chapter 6 Debug Commands debug ethport S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug ethport To enable Ethernet port debugging, use the debug ethport command in EXEC mode.
Page 377: Debug Ethport
Chapter 6 Debug Commands debug ethport S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command Description no debug all...
Page 378: Debug Exceptionlog
Chapter 6 Debug Commands debug exceptionlog S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug exceptionlog To enable the exception log debugging feature, use the debug exceptionlog command in EXEC mode.
Page 379 Chapter 6 Debug Commands debug fabric-binding S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug fabric-binding To enable debugging for the fabric binding feature, use the debug fabric-binding command in EXEC mode.
Page 380: Debug Fabric-Binding
Chapter 6 Debug Commands debug fabric-binding S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 381 Chapter 6 Debug Commands debug fc-tunnel S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug fc-tunnel To enable debugging for the Fibre Channel tunnel feature, use the debug fc-tunnel command in EXEC mode.
Page 382: Debug Fc-Tunnel
Chapter 6 Debug Commands debug fc-tunnel S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Examples The following example displays the system output when the debug fc-tunnel all command is issued: switch# debug fc-tunnel all...
Page 383: Debug Fc2
Chapter 6 Debug Commands debug fc2 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug fc2 To enable debugging for the FC2 feature, use the debug fc2 command in EXEC mode.
Page 384: Debug Fc2
Chapter 6 Debug Commands debug fc2 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m loopback Enables FC2 loopback debugging.
Page 385: Debug Fc2D
Chapter 6 Debug Commands debug fc2d S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug fc2d To enable debugging for the FC2 feature, use the debug fc2 command in EXEC mode.
Page 386: Debug Fc2D
Chapter 6 Debug Commands debug fc2d S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 387: Debug Fcc
Chapter 6 Debug Commands debug fcc S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug fcc To enable debugging for the Fibre Channel Congestion (FCC) function, use the debug fcc command in EXEC mode.
Page 388: Debug Fcc
Chapter 6 Debug Commands debug fcc S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch# debug fcc all Related Commands Command...
Page 389: Debug Fcdomain
Chapter 6 Debug Commands debug fcdomain S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug fcdomain To enable debugging for the fcdomain feature, use the debug fcdomain command in EXEC mode.To disable a debug command, use the no form of the command or use the no debug all command to turn...
Page 390: Debug Fcdomain
Chapter 6 Debug Commands debug fcdomain S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Usage Guidelines None.
Page 391: Debug Fcfwd
Chapter 6 Debug Commands debug fcfwd S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug fcfwd To enable debugging for the Fibre Channel forwarding feature, use the debug fcfwd command in EXEC mode.
Page 392: Debug Fcfwd
Chapter 6 Debug Commands debug fcfwd S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command Description no debug all...
Page 393: Debug Fcns
Chapter 6 Debug Commands debug fcns S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug fcns To enable debugging for name server registration, use the debug fcns command in EXEC mode.
Page 394: Debug Fcns
Chapter 6 Debug Commands debug fcns S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command Description show fcns database...
Page 395: Debug Fcs
Chapter 6 Debug Commands debug fcs S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug fcs To enable debugging for the fabric configuration server, use the debug fcs command in EXEC mode.
Page 396: Debug Fcs
Chapter 6 Debug Commands debug fcs S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 397 Chapter 6 Debug Commands debug fcsp-mgr S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug fcsp-mgr To enable debugging for the Fibre Channel Security Protocol (FC-SP) manager, use the debug fcsp-mgr command in EXEC mode.
Page 398: Debug Fcsp-Mgr
Chapter 6 Debug Commands debug fcsp-mgr S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Usage Guidelines None.
Page 399: Debug Fdmi
Chapter 6 Debug Commands debug fdmi S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug fdmi To enable debugging for the Fabric-Device Management Interface (FDMI) feature, use the debug fdmi command in EXEC mode.
Page 400: Debug Fdmi
Chapter 6 Debug Commands debug fdmi S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Usage Guidelines None.
Page 401: Debug Ficon
Chapter 6 Debug Commands debug ficon S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug ficon To enable debugging for the FI-bre CON-nection (FICON) interface capabilities, use the debug ficon command in EXEC mode.
Page 402: Debug Ficon
Chapter 6 Debug Commands debug ficon S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m error Enables debugging for FICON errors.
Page 403: Debug Flogi
Chapter 6 Debug Commands debug flogi S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug flogi To enable debugging for the fabric login (FLOGI) feature, use the debug flogi command in EXEC mode.
Page 404: Debug Flogi
Chapter 6 Debug Commands debug flogi S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Defaults Disabled.
Page 405: Debug Fm
Chapter 6 Debug Commands debug fm S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug fm To enable feature manager debugging, use the debug fm command in EXEC mode.
Page 406: Debug Fspf
Chapter 6 Debug Commands debug fspf S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug fspf To enable debugging for the FSPF feature, use the debug fspf command in EXEC mode.
Page 407: Debug Fspf
Chapter 6 Debug Commands debug fspf S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Defaults Disabled.
Page 408: Debug Hardware Arbiter
Chapter 6 Debug Commands debug hardware arbiter S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug hardware arbiter To configure debugging for the hardware arbiter driver, use the debug hardware arbiter command in EXEC mode.
Page 409: Debug Idehsd
Chapter 6 Debug Commands debug idehsd S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug idehsd To enable IDE hot swap handler debugging, use the debug idehsd command in EXEC mode.
Page 410: Debug Ike
Chapter 6 Debug Commands debug ike S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug ike To enable debugging for the IKE protocol, use the debug ike command in EXEC mode.
Page 411: Debug Ilc_Helper
Chapter 6 Debug Commands debug ilc_helper S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug ilc_helper To enable ILC helper debugging, use the debug ilc_helper command in EXEC mode.
Page 412: Debug Ipacl
Chapter 6 Debug Commands debug ipacl S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug ipacl To enable IP access control list (ACL) debugging, use the debug ipacl command in EXEC mode.
Page 413: Debug Ipconf
Chapter 6 Debug Commands debug ipconf S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug ipconf To enable IP configuration debugging, use the debug ipconf command in EXEC mode.
Page 414: Debug Ipfc
Chapter 6 Debug Commands debug ipfc S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug ipfc To enable IP over Fibre Channel (IPFC) debugging, use the debug ipfc command in EXEC mode.
Page 415: Debug Ips
Chapter 6 Debug Commands debug ips S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug ips To enable debugging for the IP Storage Services (IPS) module, use the debug ips command in EXEC mode.
Page 416: Debug Ips
Chapter 6 Debug Commands debug ips S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Defaults Disabled.
Page 417: Debug Ipsec
Chapter 6 Debug Commands debug ipsec S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug ipsec To enable debugging for IPsec, use the debug ipsec command in EXEC mode.To disable a debug command, use the no form of the command or use the no debug all command to turn off all debugging.
Page 418: Debug Ipsec
Chapter 6 Debug Commands debug ipsec S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 419: Debug Isns
Chapter 6 Debug Commands debug isns S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug isns To enable debugging for Internet storage name services (iSNS), use the debug isns command in EXEC mode.
Page 420: Debug Isns
Chapter 6 Debug Commands debug isns S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 421: Debug Ivr
Chapter 6 Debug Commands debug ivr S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug ivr To enable debugging for inter-VSAN routing (IVR), use the debug ivr command in EXEC mode.
Page 422: Debug Ivr
Chapter 6 Debug Commands debug ivr S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Defaults Disabled.
Page 423: Debug Klm
Chapter 6 Debug Commands debug klm S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug klm To enable kernel loadable module parameter debugging, use the debug klm command in EXEC mode.
Page 424: Debug Klm
Chapter 6 Debug Commands debug klm S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Examples The following example displays the system output when the debug klm scsi-target driver command is issued:...
Page 425: Debug License
Chapter 6 Debug Commands debug license S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug license To enable licensing debugging, use the debug license command in EXEC mode.
Page 426: Debug Logfile
Chapter 6 Debug Commands debug logfile S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug logfile To direct the output of the debug commands to a specified file, use the debug logfile command in EXEC mode.
Page 427: Debug Logfile
Chapter 6 Debug Commands debug logfile S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 428: Debug Mcast
Chapter 6 Debug Commands debug mcast S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug mcast To enable debugging for multicast definitions, use the debug mcast command in EXEC mode.
Page 429: Debug Mcast
Chapter 6 Debug Commands debug mcast S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Usage Guidelines None.
Page 430: Debug Mip
Chapter 6 Debug Commands debug mip S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug mip To enable debugging for multiple IP (MIP) kernel drivers, use the debug mip command in EXEC mode.
Page 431: Debug Module
Chapter 6 Debug Commands debug module S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug module To enable debugging for switching or service modules, use the debug module command in EXEC mode.
Page 432: Debug Ntp
Chapter 6 Debug Commands debug ntp S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug ntp To enable debugging for the Network Time Protocol (NTP) module, use the debug ntp command in EXEC mode.
Page 433: Debug Npv
Chapter 6 Debug Commands debug npv S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug npv To enable debugging N Port Virtualization (NPV) configuration on the switch, use the debug npv command.
Page 434: Debug Npv
Chapter 6 Debug Commands debug npv S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Server Interface FSM Errors debugging is on Server Interface FSM Trace debugging is on Events debugging is on...
Page 435: Debug Obfl
Chapter 6 Debug Commands debug obfl S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug obfl To enable debugging for Onboard Failure Logging (OBFL), use the debug obfl command in EXEC mode.
Page 436: Debug Platform
Chapter 6 Debug Commands debug platform S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug platform To enable debugging for the platform manager, use the debug platform command in EXEC mode.
Page 437: Debug Platform
Chapter 6 Debug Commands debug platform S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Usage Guidelines None.
Page 438: Debug Plog
Chapter 6 Debug Commands debug plog S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug plog To enable debugging of persistent logging (PLOG), use the debug plog command in EXEC mode.
Page 439: Debug Port
Chapter 6 Debug Commands debug port S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug port To enable debugging for ports, use the debug port command in EXEC mode.
Page 440: Debug Port
Chapter 6 Debug Commands debug port S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command History Release Modification...
Page 441 Chapter 6 Debug Commands debug port-channel S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug port-channel To enable debugging for PortChannels, use the debug port-channel command in EXEC mode.
Page 442: Debug Port-Channel
Chapter 6 Debug Commands debug port-resources S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug port-resources To enable debugging for a port resources module, use the debug port-resources command in EXEC mode.
Page 443: Debug Port-Resources
Chapter 6 Debug Commands debug port-resources S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m 2006 Jan 19 22:10:59.245205 port-resources: fu_fsm_engine: line[2205] 2006 Jan 19 22:10:59.245248 port-resources: prm_demux: ev[0] ips-hac2# 2006 Jan 19 22:10:59.246440 port-resources: fu_fsm_execute_all: match_...
Page 444: Debug Qos
Chapter 6 Debug Commands debug qos S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug qos To enable debugging for quality of service (QoS), use the debug qos command in EXEC mode.
Page 445: Debug Radius
Chapter 6 Debug Commands debug radius S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug radius To enable debugging for boot variables, use the debug radius command in EXEC mode.
Page 446: Debug Radius
Chapter 6 Debug Commands debug radius S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Nov 20 06:36:42 radius: radius_new_enable_info_config: got back the return value of configuration operation:success Nov 20 06:36:42 radius: radius_new_debug_conf_close: entering...
Page 447: Debug Rd-Reg
Chapter 6 Debug Commands debug rd-reg S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug rd-reg To enable debugging for the list of devices using the read-register feature, use the debug rd-reg command in EXEC mode.
Page 448: Debug Rdl Errors
Chapter 6 Debug Commands debug rdl errors S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug rdl errors To enable debugging for RDL errors, use the debug rdl errors command in EXEC mode.
Page 449: Debug Rib
Chapter 6 Debug Commands debug rib S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug rib To enable debugging for the routing information base (RIB) feature, use the debug rib command in EXEC mode.
Page 450: Debug Rlir
Chapter 6 Debug Commands debug rlir S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug rlir To enable Registered Link Incident Report (RLIR) debugging, use the debug rlir command in EXEC mode.
Page 451: Debug Rscn
Chapter 6 Debug Commands debug rscn S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug rscn To enable debugging for the registered state change notification (RSCN) feature, use the debug rscn command in EXEC mode.
Page 452 Chapter 6 Debug Commands debug san-ext-tuner S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug san-ext-tuner To enable debugging for SAN extension tuner, use the debug san-ext-tuner command in EXEC mode.
Page 453: Debug San-Ext-Tuner
Chapter 6 Debug Commands debug san-ext-tuner S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command Description show isns...
Page 454 Chapter 6 Debug Commands debug scsi-flow S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug scsi-flow To enable debugging of a SCSI flow, use the debug scsi-flow command.
Page 455: Debug Scsi-Flow
Chapter 6 Debug Commands debug scsi-flow S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 456: Debug Scsi-Target
Chapter 6 Debug Commands debug scsi-target S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug scsi-target To enable debugging for SCSI targets, use the debug scsi-target command in EXEC mode.
Page 457: Debug Sdv
Chapter 6 Debug Commands debug sdv S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug sdv To enable debugging for SAN device virtualization, use the debug sdv command in EXEC mode.
Page 458: Debug Sdv
Chapter 6 Debug Commands debug sdv S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Usage Guidelines None.
Page 459: Debug Security
Chapter 6 Debug Commands debug security S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug security To enable debugging for the security and accounting features, use the debug security command in EXEC mode.
Page 460: Debug Sensor
Chapter 6 Debug Commands debug sensor S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug sensor To enable debugging for the sensor manager, use the debug sensor command in EXEC mode.
Page 461: Debug Sme
Chapter 6 Debug Commands debug sme S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug sme To enable debugging for the Cisco SME features, use the debug sme command.
Page 462: Debug Sme
Chapter 6 Debug Commands debug sme S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m (34916564), MTS_OPC_DEBUG_WRAP_MSG 2007 Sep 23 15:44:44.491096 sme: fu_fsm_engine: line[2253] 2007 Sep 23 15:44:44.492596 sme: fu_fsm_execute_all: match_msg_id(0), log_alread...
Page 463: Debug Snmp
Chapter 6 Debug Commands debug snmp S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug snmp To enable debugging for the SNMP manager, use the debug snmp command in EXEC mode.
Page 464: Debug Snmp
Chapter 6 Debug Commands debug snmp S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Examples The following example displays the system output when the debug snmp trace command is issued: switch# debug snmp trace...
Page 465: Debug Span
Chapter 6 Debug Commands debug span S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug span To enable SPAN debugging, use the debug span command in EXEC mode.
Page 466: Debug Span
Chapter 6 Debug Commands debug span S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 467: Debug System Health
Chapter 6 Debug Commands debug system health S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug system health To enable system health monitoring debugging, use the debug system health command in EXEC mode.
Page 468: Debug System Health
Chapter 6 Debug Commands debug system health S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command Modes EXEC mode.
Page 469: Debug Tacacs
Chapter 6 Debug Commands debug tacacs+ S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug tacacs+ To enable debugging for boot variables, use the debug tacacs+ command in EXEC mode.
Page 470: Debug Tacacs+
Chapter 6 Debug Commands debug tacacs+ S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Nov 20 06:39:44 tacacs: tacacs_enable_info_config: got back the return value of configuration operation:success Nov 20 06:39:44 tacacs: tacacs_debug_conf_close: entering...
Page 471: Debug Tcap
Chapter 6 Debug Commands debug tcap S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug tcap To enable debugging the exception logger, use the debug tcap command in EXEC mode.
Page 472: Debug Tlport
Chapter 6 Debug Commands debug tlport S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug tlport To enable debugging for TL port interfaces, use the debug tlport command in EXEC mode.
Page 473: Debug Ttyd
Chapter 6 Debug Commands debug ttyd S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug ttyd To enable TTYD debugging, use the debug ttyd command in EXEC mode.
Page 474: Debug Vni
Chapter 6 Debug Commands debug vni S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug vni To enable debugging for a virtual network interface (VNI), use the debug vni command in EXEC mode.
Page 475: Debug Vrrp
Chapter 6 Debug Commands debug vrrp S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug vrrp To enable debugging for a Virtual Router Redundancy Protocol (VRRP), use the debug vrrp command in EXEC mode.
Page 476: Debug Vrrp
Chapter 6 Debug Commands debug vrrp S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command Description no debug all...
Page 477: Debug Vsan
Chapter 6 Debug Commands debug vsan S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug vsan To enable debugging for VSANs, use the debug vsan command in EXEC mode.
Page 478: Debug Vsan
Chapter 6 Debug Commands debug vsan S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 479: Debug Wr-Reg
Chapter 6 Debug Commands debug wr-reg S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug wr-reg To enable debugging for the list of devices using the write-register feature, use the debug wr-reg command in EXEC mode.
Page 480: Debug Wwn
Chapter 6 Debug Commands debug wwn S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug wwn To enable debugging for the world wide name (WWN) manager, use the debug wwn command in EXEC mode.
Page 481: Debug Wwn
Chapter 6 Debug Commands debug wwn S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Apr 29 19:24:17 wwn: 53601-wwnm_unmask_sigalrm:1261 TRACE: FILE=_manager/wwnm/wwnm_utilities.c...
Page 482: Debug Xbar
Chapter 6 Debug Commands debug xbar S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug xbar To enable crossbar debugging (XBAR), use the debug xbar command in EXEC mode.
Page 483: Debug Xbar
Chapter 6 Debug Commands debug xbar_driver S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug xbar_driver To enable debugging of the crossbar driver (XBAR driver), use the debug xbar_driver command in EXEC mode.
Page 484: Debug Xbc
Chapter 6 Debug Commands debug xbc S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug xbc To enable crossbar client debugging (XBC), use the debug xbc command in EXEC mode.
Page 485: Debug Zone
Chapter 6 Debug Commands debug zone S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m debug zone To enable debugging for zones, use the debug zone command in EXEC mode.
Page 486: Debug Zone
Chapter 6 Debug Commands debug zone S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Usage Guidelines None.
Page 487 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C H A P T E R E Commands The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric...
Page 488: Chapter 7 E Command
Chapter 7 E Commands email-contact S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m email-contact To configure an e-mail contact with the Call Home function, use the email-addr command in Call Home configuration submode.
Page 489 Chapter 7 E Commands enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m enable To enable the Call Home function, use the enable command in Call Home configuration submode.
Page 490: Enable
Chapter 7 E Commands encryption S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m encryption To configure an encryption algorithm for an IKE protocol policy, use the encryption command.
Page 491 Chapter 7 E Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m To exit any of the configuration modes and return to EXEC mode, use the end command in configuration mode.
Page 492: Enrollment Terminal
Chapter 7 E Commands enrollment terminal S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m enrollment terminal To enable manual cut-and-paste certificate enrollment through the switch console, use the enrollment terminal command in trust point configuration submode.
Page 493 Chapter 7 E Commands errdisable detect cause link-down S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m errdisable detect cause link-down To error disable and bring down a port on a link failure, use the errdisable detect cause link-down command.
Page 494: Errdisable Detect Cause Link-Down
Chapter 7 E Commands errdisable detect cause link-down S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 495 Chapter 7 E Commands event S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m event To configure the event statement for the policy, use the event command.
Page 496: Event
Chapter 7 E Commands event S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m entry-op op (Optional) Compares the contents of the current counter with the exit value using a specified operator:...
Page 497 Chapter 7 E Commands event S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m get-type Specifies the type of SNMP get operation to be applied to the object ID specified by the OID value argument.
Page 498 Chapter 7 E Commands event S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m This following example shows how to specify that an EEM applet runs when a fan absent event occurs: switch# configure terminal switch(config)# event manager applet absent-applet...
Page 499 Chapter 7 E Commands event S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Cisco MDS 9000 Family Command Reference 7-13 OL-18089-01, Cisco MDS NX-OS Release 4.x...
Page 500: Event Manager Applet
Chapter 7 E Commands event manager applet S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m event manager applet To register an applet with the Embedded Event Manager (EEM) and to enter applet configuration mode, use the event manager applet command.
Page 501: Event Manager Applet
Chapter 7 E Commands event manager policy S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m event manager policy To register and activate an Embeded Event Manager policy (EEM) script policy, use the event manager policy command.
Page 502: Event Manager Policy
Chapter 7 E Commands event manager environment S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m event manager environment To configure an EEM environment variable, use the event manager environment command.
Page 503 Chapter 7 E Commands exit S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m exit To exit any configuration mode or close an active terminal session and terminate the EXEC, use the exit command at the system prompt.
Page 504: Exit
Chapter 7 E Commands exit S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch# exit Related Commands Command...
Page 505 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C H A P T E R F Commands The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric...
Page 506: Chapter 8 F Command
Chapter 8 F Commands fabric S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fabric To add a fabric to the cluster, use the fabric command in the Cisco SME cluster configuration submode.
Page 507: Fabric-Binding Activate
Chapter 8 F Commands fabric-binding activate S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fabric-binding activate To activate fabric binding in a VSAN, use the fabric-binding activate command in configuration mode.
Page 508 Chapter 8 F Commands fabric-binding activate S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 509: Fabric-Binding Database Copy
Chapter 8 F Commands fabric-binding database copy S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fabric-binding database copy To copy from the active fabric binding database to the configuration fabric binding database, use the fabric-binding database copy command in EXEC mode.
Page 510: Fabric-Binding Database Diff
Chapter 8 F Commands fabric-binding database diff S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fabric-binding database diff To view the differences between the active database and the configuration database in a VSAN, use the fabric-binding database diff command in EXEC mode.
Page 511: Fabric-Binding Database Vsan
Chapter 8 F Commands fabric-binding database vsan S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fabric-binding database vsan To configure a user-specified fabric binding list in a VSAN, use the fabric-binding database vsan command in configuration mode.
Page 512 Chapter 8 F Commands fabric-binding database vsan S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Examples The following example enters the fabric binding database submode and adds the sWWN and domain ID of a switch to the configured database list.
Page 513: Fabric-Binding Enable
Chapter 8 F Commands fabric-binding enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fabric-binding enable To enable fabric binding in a VSAN, use the fabric-binding enable command.
Page 514: Fabric-Membership
Chapter 8 F Commands fabric-membership S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fabric-membership To configure a node to a fabric, use the fabric-membership command.
Page 515: Fcalias Clone
Chapter 8 F Commands fcalias clone S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcalias clone To clone a Fibre Channel alias, use the fcalias clone command.
Page 516: Fcalias Name
Chapter 8 F Commands fcalias name S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcalias name To configure an FC alias, use the fcalias name command.
Page 517: Fcalias Rename
Chapter 8 F Commands fcalias rename S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcalias rename To rename a Fibre Channel alias (fcalias), use the fcalias rename command.
Page 518: Fcanalyzer
Chapter 8 F Commands fcanalyzer S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcanalyzer To configure the Cisco Fabric Analyzer use the fcanalyzer command in configuration mode.
Page 519 Chapter 8 F Commands fcanalyzer S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch(config)# fcanalyzer local limit-frame-size 64 Capturing on eth2 switch(config)# fcanalyzer local limit-captured-frames 10...
Page 520: Fcc Enable
Chapter 8 F Commands fcc enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcc enable To enable Fibre Channel Congestion Control (FCC), use the fcc enable command in configuration mode.
Page 521: Fcc Priority
Chapter 8 F Commands fcc priority S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcc priority To assign the FCC priority to the entire switch, use the fcc priority command in configuration mode.
Page 522: Fcdomain
Chapter 8 F Commands fcdomain S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcdomain To configure the Fibre Channel domain feature, use the fcdomain command.
Page 523 Chapter 8 F Commands fcdomain S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Defaults Enabled.
Page 524 Chapter 8 F Commands fcdomain S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 525: Fcdomain Abort Vsan
Chapter 8 F Commands fcdomain abort vsan S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcdomain abort vsan To flush cached data without committing and release the lock, use the fcdomain abort vsan command.
Page 526: Fcdomain Commit Vsan
Chapter 8 F Commands fcdomain commit vsan S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcdomain commit vsan To commit cached data and release the lock, use the fcdomain commit vsan command.
Page 527: Fcdomain Distribute
Chapter 8 F Commands fcdomain distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcdomain distribute To enable fabric distribution using Cisco Fabric Services (CFS), use the fcdomain distribute command.
Page 528: Fcdomain Rcf-Reject
Chapter 8 F Commands fcdomain rcf-reject S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcdomain rcf-reject To enable the RCF reject flag for a Fibre Channel or FCIP interface, use the fcdomain option.
Page 529: Fcdroplatency
Chapter 8 F Commands fcdroplatency S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcdroplatency To configure the network and switch FC drop latency time, use the fcdroplatency command in configuration mode.
Page 530 Chapter 8 F Commands fcdroplatency S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 531: Fcflow Stats
Chapter 8 F Commands fcflow stats S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcflow stats To configure fcflow statistics, use the fcflow stats command in configuration mode.
Page 532 Chapter 8 F Commands fcflow stats S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example enables the flow counter for module 1.
Page 533: Fcid-Allocation
Chapter 8 F Commands fcid-allocation S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcid-allocation Use the fcid-allocation command to manually add a FCID to the default area company ID list.
Page 534 Chapter 8 F Commands fcid-allocation S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 535: Fcid-Last-Byte
Chapter 8 F Commands fcid-last-byte S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcid-last-byte Use the fcid-last-byte command to allocate the last byte FCID for the fabric address.
Page 536: Fcinterop Fcid-Allocation
Chapter 8 F Commands fcinterop fcid-allocation S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcinterop fcid-allocation To allocate FCIDs on the switch, use the fcinterop fcid-allocation command in configuration mode.
Page 537: Fcinterop Loop-Monitor
Chapter 8 F Commands fcinterop loop-monitor S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcinterop loop-monitor To monitor removal of discs from a loop port, use the fcinterop loop-monitor command in configuration mode.
Page 538: Fcip Enable
Chapter 8 F Commands fcip enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcip enable To enable the FCIP feature in any switch in the Cisco MDS Family, issue the fcip enable command.
Page 539: Fcip Profile
Chapter 8 F Commands fcip profile S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcip profile To create and configure an FCIP profile, use the fcip profile command.
Page 540: Fcns Proxy-Port
Chapter 8 F Commands fcns proxy-port S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcns proxy-port To register a name server proxy, use the fcns proxy-port command in configuration mode.
Page 541: Fcns Reject-Duplicate-Pwwn Vsan
Chapter 8 F Commands fcns reject-duplicate-pwwn vsan S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcns reject-duplicate-pwwn vsan To reject duplicate Fibre Channel name server (FCNS) proxies on a VSAN, use the fcns reject-duplicate-pwwn vsan command in configuration mode.
Page 542: Fcping
Chapter 8 F Commands fcping S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcping To ping an N port with a specified FCID, use the fcping fcid command in EXEC mode.
Page 543 Chapter 8 F Commands fcping S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m 5 frames sent, 5 frames received, 0 timeouts Round-trip min/avg/max = 165/270/730 usec The following example shows the setting of the number of frames to be sent using the count option.
Page 544: Fc-Redirect Version2 Enable
Chapter 8 F Commands fc-redirect version2 enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fc-redirect version2 enable To enable the version2 mode in FC-Redirect, use the fc-redirect version2 enable command in configuration mode.
Page 545: Enable Mode
Chapter 8 F Commands fc-redirect version2 enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m added to the fabric will automatically be configured in version2 mode.
Page 546: Fcroute
Chapter 8 F Commands fcroute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcroute To configure Fibre Channel routes and to activate policy routing, use the fcroute command.
Page 547 Chapter 8 F Commands fcroute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example removes this configuration.
Page 548: Fcrxbbcredit Extended Enable
Chapter 8 F Commands fcrxbbcredit extended enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcrxbbcredit extended enable To enable Fibre Channel extended buffer-to-buffer credits (BB_credits), use the fcrxbbcredit extended enable command in configuration mode.
Page 549: Fcs Plat-Check-Global Vsan
Chapter 8 F Commands fcs plat-check-global vsan S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcs plat-check-global vsan To enable FCS platform and node name checking fabric wide, use the fcs plat-check-global vsan command in configuration mode.
Page 550: Fcs Register
Chapter 8 F Commands fcs register S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcs register To register FCS attributes, use the fcs register command in configuration mode.
Page 551: Fcs Virtual-Device-Add
Chapter 8 F Commands fcs virtual-device-add S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcs virtual-device-add To include a virtual device in a query about zone information from an FCS, use the fcs virtual-device-add command in configuration mode.
Page 552: Fcsp Dhchap
Chapter 8 F Commands fcsp dhchap S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcsp dhchap To configure DHCHAP options in a switch, use the fcsp dhchap command in configuration mode.
Page 553 Chapter 8 F Commands fcsp dhchap S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Examples The following example enables FC-SP.
Page 554 Chapter 8 F Commands fcsp dhchap S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example configures a password for another switch in the fabric which is identified by the Switch WWN device name.
Page 555: Fcsp Enable
Chapter 8 F Commands fcsp enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcsp enable To enable the Fibre Channel Security Protocol (FC-SP) in a switch, use the fcsp enable command in configuration mode.
Page 556: Fcsp Timeout
Chapter 8 F Commands fcsp timeout S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fcsp timeout To configure the timeout value for FC-SP message, use the fcsp timeout command in configuration mode.
Page 557: Fctimer
Chapter 8 F Commands fctimer S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fctimer To change the default Fibre Channel timers, use the fctimer command in configuration mode.
Page 558: Fctimer Abort
Chapter 8 F Commands fctimer abort S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fctimer abort To discard a Fibre Channel timer (fctimer) Cisco Fabric Services (CFS) distribution session in progress, use the fctimer abort command in configuration mode.
Page 559: Fctimer Commit
Chapter 8 F Commands fctimer commit S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fctimer commit To apply the pending configuration pertaining to the Fibre Channel timer (fctimer) Cisco Fabric Services (CFS) distribution session in progress in the fabric, use the fctimer commit command in configuration...
Page 560: Fctimer Distribute
Chapter 8 F Commands fctimer distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fctimer distribute To enable Cisco Fabric Services (CFS) distribution for Fibre Channel timer (fctimer), use the fctimer distribute command.
Page 561: Fctrace
Chapter 8 F Commands fctrace S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fctrace To trace the route to an N port, use the fctrace command in EXEC mode.
Page 562: Fc-Tunnel
Chapter 8 F Commands fc-tunnel S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fc-tunnel To terminate a Fibre Channel tunnel in a destination switch, use the fc-tunnel command.
Page 563 Chapter 8 F Commands fc-tunnel S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example places you at the explicit path prompt for the path named Path 1and specifies that the next hop VSAN interface IP addresses.
Page 564: Feature
Chapter 8 F Commands feature S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m feature To enable a feature or service on the switch, use the feature command.
Page 565 Chapter 8 F Commands feature S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command Modes Configuration mode.
Page 566: Ficon Enable
Chapter 8 F Commands ficon enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ficon enable To enable the FICON feature on a switch, use the ficon enable command in configuration mode.
Page 567 Chapter 8 F Commands ficon enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 568: Ficon Logical-Port Assign Port-Numbers
Chapter 8 F Commands ficon logical-port assign port-numbers S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ficon logical-port assign port-numbers To reserve FICON port numbers for logical interfaces on the switch, use the ficon logical-port assign port-numbers command in configuration mode.
Page 569: Ficon Port Default-State Prohibit-All
Chapter 8 F Commands ficon port default-state prohibit-all S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ficon port default-state prohibit-all To set the FICON port default state to prohibit all, use the ficon port default-state prohibit-all command in configuration mode.
Page 570: Ficon Slot Assign Port-Numbers
Chapter 8 F Commands ficon slot assign port-numbers S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ficon slot assign port-numbers To reserve FICON port numbers for a slot on the switch, use the ficon slot assign port-numbers command in configuration mode.
Page 571 Chapter 8 F Commands ficon slot assign port-numbers S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m swich# config terminal Enter configuration commands, one per line.
Page 572: Ficon Swap
Chapter 8 F Commands ficon swap S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ficon swap To enable the FICON feature in a specified VSAN, use the ficon swap command in configuration mode.
Page 573 Chapter 8 F Commands ficon swap S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch# ficon swap portnumber 3 15 after swap noshut The following example swaps the contents of ports 3 with port 15 and shuts them down.
Page 574: Ficon-Tape-Accelerator Vsan
Chapter 8 F Commands ficon-tape-accelerator vsan S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ficon-tape-accelerator vsan To enable FICON tape acceleration for the FCIP interface, use the ficon-tape-accelerator vsan command in interface configuration submode.
Page 575 Chapter 8 F Commands ficon-tape-accelerator vsan S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 576: Ficon Vsan (Exec Mode)
Chapter 8 F Commands ficon vsan (EXEC mode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ficon vsan (EXEC mode) To configure FICON related parameters in EXEC mode, use the ficon vsan command.
Page 577 Chapter 8 F Commands ficon vsan (EXEC mode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 578: Ficon Vsan (Configuration Mode)
Chapter 8 F Commands ficon vsan (configuration mode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ficon vsan (configuration mode) To enable the FICON feature in a specified VSAN, use the ficon vsan command in configuration mode.
Page 579: File
Chapter 8 F Commands file S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m file To access FICON configuration files in a specified VSAN, use the file command.
Page 580: Find
Chapter 8 F Commands find S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m find To display a list of files on a file system, use the find command in EXEC mode.
Page 581: Flex-Attach Virtual-Pwwn
Chapter 8 F Commands flex-attach virtual-pwwn S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m flex-attach virtual-pwwn To map the real port WWN (pWWN) and a user-specific virtual pWWN, use the flex-attach virtual-pwwn command.
Page 582: Flex-Attach Virtual-Pwwn Auto
Chapter 8 F Commands flex-attach virtual-pwwn auto S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m flex-attach virtual-pwwn auto To enable the FlexAttach virtual port WWN (pWWN) on a specific interface, use the flex-attach virtual-pwwn auto command.
Page 583: Flex-Attach Virtual-Pwwn Interface
Chapter 8 F Commands flex-attach virtual-pwwn interface S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m flex-attach virtual-pwwn interface To set the user-specific FlexAttach virtual port WWN (pWWN) on an interface, use the flex-attach virtual-pwwn interface command.
Page 584: Format
Chapter 8 F Commands format S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m format To erase all the information on a module, use the format command in EXEC mode.
Page 585 Chapter 8 F Commands format S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example erases all information on usb2:.
Page 586: Fspf Config Vsan
Chapter 8 F Commands fspf config vsan S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fspf config vsan To configure an FSPF feature for the entire VSAN, use the fspf config vsan command in configuration mode.
Page 587 Chapter 8 F Commands fspf config vsan S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command History Release Modification...
Page 588: Fspf Cost
Chapter 8 F Commands fspf cost S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fspf cost To configure FSPF link cost for an FCIP interface, use the fspf cost command.
Page 589: Fspf Dead-Interval
Chapter 8 F Commands fspf dead-interval S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fspf dead-interval To set the maximum interval for which a hello message must be received before the neighbor is considered lost, use the fspf dead-interval command.
Page 590: Fspf Enable Vsan
Chapter 8 F Commands fspf enable vsan S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fspf enable vsan To enable FSPF for a VSAN, use the fspf enable command in configuration mode.
Page 591: Fspf Hello-Interval
Chapter 8 F Commands fspf hello-interval S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fspf hello-interval To verify the health of the link, use the fspf hello-interval command.
Page 592: Fspf Passive
Chapter 8 F Commands fspf passive S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fspf passive To disable the FSPF protocol for selected interfaces, use the fspf passive command.
Page 593: Fspf Retransmit-Interval
Chapter 8 F Commands fspf retransmit-interval S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m fspf retransmit-interval To specify the time after which an unacknowledged link state update should be transmitted on the interface, use the fspf retransmit-interval command.
Page 594 Chapter 8 F Commands fspf retransmit-interval S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Cisco MDS 9000 Family Command Reference 8-90 OL-18089-01, Cisco MDS NX-OS Release 4.x...
Page 595 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C H A P T E R G Commands The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric...
Page 596: Chapter 9 G Command
Chapter 9 G Commands group S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m group To configure a Modular Exponentiation (MODP) Diffie-Hellman (DH) group for an IKE protocol policy, use the group command in IKE policy configuration submode.
Page 597 Chapter 9 G Commands gzip S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m gzip To compress (zip) a specified file using LZ77 coding, use the gzip command in EXEC mode.
Page 598: Gzip
Chapter 9 G Commands gzip S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command Description gunzip...
Page 599 Chapter 9 G Commands gunzip S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m gunzip To uncompress (unzip) LZ77 coded files, use the gunzip command in EXEC mode.
Page 600: Gunzip
Chapter 9 G Commands gunzip S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Cisco MDS 9000 Family Command Reference OL-18089-01, Cisco MDS NX-OS Release 4.x...
Page 601 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C H A P T E R H Commands The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric...
Page 602: Chapter 10 H Command
Chapter 10 H Commands hash S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m hash To configure a hash algorithm for an IKE protocol policy, use the hash command in IKE policy configuration submode.
Page 603 Chapter 10 H Commands host S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m host Use the host command to configure the switch offline state, the mainframe access control parameters, and the mainframe time stamp parameters.
Page 604: Host
Chapter 10 H Commands host S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example prohibits mainframe users from changing the VSAN-specific clock: switch(config-ficon)# no host set-timestamp The following example allows the host to set the clock on this switch (default):...
Page 605 Chapter 10 H Commands hw-module logging onboard S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m hw-module logging onboard To configure on-board failure logging (OBFL), use the hw-module logging onboard command.
Page 606: Hw-Module Logging Onboard
Chapter 10 H Commands hw-module logging onboard S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Cisco MDS 9000 Family Command Reference 10-6 OL-18089-01, Cisco MDS NX-OS Release 4.x...
Page 607 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C H A P T E R I Commands The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric...
Page 608: Chapter 11 I Command
Chapter 11 I Commands identity S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m identity To configure the identity for the IKE protocol, use the identity command in IKE configuration submode.
Page 609 Chapter 11 I Commands identity S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 610: In-Order-Guarantee
Chapter 11 I Commands in-order-guarantee S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m in-order-guarantee To enable in-order delivery, use the in-order-guarantee command in configuration mode.
Page 611: Initiator
Chapter 11 I Commands initiator S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m initiator To configure the initiator version and address, use the initiator command IKE configuration submode.
Page 612: Install All
Chapter 11 I Commands install all S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m install all To upgrade all modules in any Cisco MDS 9000 family switch, use the install all command.
Page 613 Chapter 11 I Commands install all S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m During a software upgrade to Cisco MDS SAN-OS 3.1(3), all modules that are online are tested and the installation stops if any modules are running with a faulty CompactFlash.
Page 614 Chapter 11 I Commands install all S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Module Image Running-Version...
Page 615 Chapter 11 I Commands install all S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCC INIT: Entering runlevel: 3...
Page 616 Chapter 11 I Commands install all S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m For scp://user@171.69.16.26, please enter password: Copying image from scp://user@171.69.16.26/tftpboot/HKrel/qa/vegas/final/m9500-sf1ek9-kickstart-mz.1.3.2a.bin...
Page 617 Chapter 11 I Commands install all S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m loader 1.2(2) 1.2(2)
Page 618: Install Clock-Module
Chapter 11 I Commands install clock-module S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m install clock-module To upgrade the EPLD images of the clock module on a Cisco MDS 9513 Switch Director, use the install clock-module command.
Page 619 Chapter 11 I Commands install clock-module S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 620: Install License
Chapter 11 I Commands install license S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m install license To program the supervisor or switching module BIOS, use the install license command.
Page 621: Install Module Bios
Chapter 11 I Commands install module bios S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m install module bios To program the supervisor or switching module BIOS, use the install module bios command.
Page 622: Install Module Epld
Chapter 11 I Commands install module epld S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m install module epld To upgrade the electrically programmable logical devices (EPLDs) module, use the install module epld command.
Page 623 Chapter 11 I Commands install module epld S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m UD chip Fix 0x05 Sahara...
Page 624: Install Module Loader
Chapter 11 I Commands install module loader S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m install module loader To upgrade the bootloader on either the active or standby supervisor module, use the install module loader command.
Page 625: Install Ssi
Chapter 11 I Commands install ssi S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m install ssi To perform a nondisruptive upgrade of the SSI image on an SSM, use the install ssi command.
Page 626: Interface
Chapter 11 I Commands interface S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m interface To configure an interface on the Cisco MDS 9000 Family of switches, use the interface command in configuration mode.
Page 627 Chapter 11 I Commands interface S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Usage Guidelines You can specify a range of interfaces by issuing a command with the following example format: interface fc1/1 - 5 , fc2/5 - 7...
Page 628: Interface Bay | Ext
Chapter 11 I Commands interface bay | ext S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m interface bay | ext To configure a Fibre Channel interface on a Cisco Fabric Switch for HP c-Class BladeSystem and on a Cisco Fabric Switch for IBM BladeCenter, use the interface bay or interface ext command in...
Page 629: Interface Fc
Chapter 11 I Commands interface fc S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m interface fc To configure a Fibre Channel interface on the Cisco MDS 9000 Family of switches, use the interface fc command in EXEC mode.
Page 630 Chapter 11 I Commands interface fc S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command History Release Modification...
Page 631: Interface Fc-Tunnel
Chapter 11 I Commands interface fc-tunnel S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m interface fc-tunnel To configure a Fibre Channel tunnel and facilitate RSPAN traffic, use the interface fc-tunnel command.
Page 632 Chapter 11 I Commands interface fc-tunnel S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example enables traffic flow through this interface: switch(config-if)# no shutdown The following example references the configured path in the source switch (switch S):...
Page 633: Interface Fcip
Chapter 11 I Commands interface fcip S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m interface fcip To configure a Fibre Channel over IP Protocol (FCIP) interface, use the interface fcip command.
Page 634 Chapter 11 I Commands interface fcip S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ficon Configures FICON parameters.
Page 635 Chapter 11 I Commands interface fcip S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Examples The following example selects an FCIP interface and enters interface configuration submode: switch# config terminal...
Page 636: Interface Gigabitethernet
Chapter 11 I Commands interface gigabitethernet S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m interface gigabitethernet To configure an Gigabit Ethernet interface, use the interface gigabitethernet command.
Page 637 Chapter 11 I Commands interface gigabitethernet S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example changes the IP maximum transmission unit (MTU) value for the selected Gigabit Ethernet interface: switch(config-if)# switchport mtu 3000...
Page 638: Interface Iscsi
Chapter 11 I Commands interface iscsi S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m interface iscsi To configure an iSCSI interface, use the interface iscsi command.
Page 639 Chapter 11 I Commands interface iscsi S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example enables the store-and-forward mode for iSCSI interfaces 9/1 to 9/4: switch(config)# interface iscsi 9/1 - 4 switch(config-if)# mode store-and-forward...
Page 640: Interface Mgmt
Chapter 11 I Commands interface mgmt S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m interface mgmt To configure a management interface, use the interface mgmt command in configuration mode.
Page 641: Interface Port-Channel
Chapter 11 I Commands interface port-channel S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m interface port-channel To configure a PortChannel interface on the Cisco MDS 9000 Family of switches, use the interface port-channel command.
Page 642 Chapter 11 I Commands interface port-channel S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command History Release Modification...
Page 643: Interface Sme
Chapter 11 I Commands interface sme S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m interface sme To configure the Cisco SME interface on a switch, use the interface sme command.
Page 644: Interface Sme (Cisco Sme Cluster Node Configuration Submode)
Chapter 11 I Commands interface sme (Cisco SME cluster node configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m interface sme (Cisco SME cluster node configuration submode) To add Cisco SME interface from a local or a remote switch to a cluster, use the interface sme command.
Page 645 Chapter 11 I Commands interface sme (Cisco SME cluster node configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 646: Interface Vsan
Chapter 11 I Commands interface vsan S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m interface vsan To configure a VSAN interface, use the interface vsan command.
Page 647: Ip Access-Group
Chapter 11 I Commands ip access-group S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ip access-group To apply an access list to an interface, use the ip access-group command in interface mode.
Page 648 Chapter 11 I Commands ip access-group S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch# config terminal Enter configuration commands, one per line.
Page 649: Ip Access-List
Chapter 11 I Commands ip access-list S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ip access-list To configure IP access control lists (ACLs), use the ip access-list command in configuration mode.
Page 650 Chapter 11 I Commands ip access-list S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m operator Compares source or destination ports to the packet and has the following options:...
Page 651 Chapter 11 I Commands ip access-list S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Examples The following example configures the an IP-ACL called aclPermit and permits IP traffic from any source address to any destination address:...
Page 652: Ip Address (Fcip Profile Configuration Submode)
Chapter 11 I Commands ip address (FCIP profile configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ip address (FCIP profile configuration submode) To assign the local IP address of a Gigabit Ethernet interface to the FCIP profile, use the ip address command.
Page 653: Ip Address (Interface Configuration)
Chapter 11 I Commands ip address (interface configuration) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ip address (interface configuration) To assign an IP address to a Gigabit Ethernet interface, use the ip address command in interface configuration submode.
Page 654: Ip-Compression
Chapter 11 I Commands ip-compression S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ip-compression To enable compression on the FCIP link, use the ip-compression command in interface configuration submode.
Page 655 Chapter 11 I Commands ip-compression S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The IP compression feature behavior differs between the IPS module(s) and the MPS-14/2 module—while mode2 and mode3 perform software compression in both modules, mode1 performs hardware-based compression in MPS-14/2 modules, and software compression in IPS-4 and IPS-8...
Page 656: Ip Default-Gateway
Chapter 11 I Commands ip default-gateway S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ip default-gateway To configure the IP address of the default gateway, use the ip default-gateway command.
Page 657: Ip Default-Network
Chapter 11 I Commands ip default-network S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ip default-network To configure the IP address of the default network, use the ip default-network command in configuration mode.
Page 658: Ip Domain-List
Chapter 11 I Commands ip domain-list S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ip domain-list To configure the IP domain list, use the ip domain-list command in configuration mode.
Page 659: Ip Domain-Lookup
Chapter 11 I Commands ip domain-lookup S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ip domain-lookup To enable the DNS server lookup feature, use the ip domain-lookup command in configuration mode.
Page 660: Ip Domain-Name
Chapter 11 I Commands ip domain-name S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ip domain-name To configure a domain name, use the ip domain-name command in configuration mode.
Page 661: Ip Name-Server
Chapter 11 I Commands ip name-server S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ip name-server To configure a name server, use the ip name-server command in configuration mode.
Page 662: Ip Route
Chapter 11 I Commands ip route S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ip route To configure a static route, use the ip route command in configuration mode.
Page 663: Ip Routing
Chapter 11 I Commands ip routing S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ip routing To enable the IP forwarding feature, use the ip routing command in configuration mode.
Page 664: Ips Netsim Delay-Ms
Chapter 11 I Commands ips netsim delay-ms S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ips netsim delay-ms To delay packets that arrive at a specified Gigabit Ethernet interface specifying milliseconds, use the ips netsim delay command in SAN extension tuner configuration submode.
Page 665: Ips Netsim Delay-Us
Chapter 11 I Commands ips netsim delay-us S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ips netsim delay-us To delay packets that arrive at a specified Gigabit Ethernet interface specifying microseconds, use the ips netsim delay command in SAN extension tuner configuration submode.
Page 666: Ips Netsim Drop Nth
Chapter 11 I Commands ips netsim drop nth S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ips netsim drop nth To drop packets every nth packet at a specified Gigabit Ethernet interface, use the ips netsim drop nth command in SAN extension tuner configuration submode.
Page 667 Chapter 11 I Commands ips netsim drop nth S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 668: Ips Netsim Drop Random
Chapter 11 I Commands ips netsim drop random S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ips netsim drop random To drop packets randomly at a specified Gigabit Ethernet interface, use the ips netsim drop random command in SAN extension tuner configuration submode.
Page 669 Chapter 11 I Commands ips netsim drop random S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 670: Ips Netsim Enable
Chapter 11 I Commands ips netsim enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ips netsim enable To enable two Gigabit Ethernet interfaces to operate in the network simulation mode, enter the ips netsim enable command in SAN extension tuner configuration submode.
Page 671: Ips Netsim Max-Bandwidth-Kbps
Chapter 11 I Commands ips netsim max-bandwidth-kbps S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ips netsim max-bandwidth-kbps To limit the bandwidth in kilobytes per second of a specified Gigabit Ethernet interface, use the ips netsim max-bandwidth-kbps command in SAN extension tuner configuration submode.
Page 672: Ips Netsim Max-Bandwidth-Mbps
Chapter 11 I Commands ips netsim max-bandwidth-mbps S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ips netsim max-bandwidth-mbps To limit the bandwidth in megabytes per second of a specified Gigabit Ethernet interface, use the ips netsim max-bandwidth-mbps command in SAN extension tuner configuration submode.
Page 673: Ips Netsim Qsize
Chapter 11 I Commands ips netsim qsize S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ips netsim qsize To limit the size of the queue on a specified Gigabit Ethernet interface, use the ips netsim qsize command in SAN extension tuner configuration submode.
Page 674: Ips Netsim Reorder
Chapter 11 I Commands ips netsim reorder S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ips netsim reorder To reorder packets entering a specified Gigabit Ethernet interface, use the ips netsim reorder command in SAN extension tuner configuration submode.
Page 675 Chapter 11 I Commands ips netsim reorder S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example shows reordering of every 50th packet with a distance limit of 5.
Page 676: Ipv6 Access-List
Chapter 11 I Commands ipv6 access-list S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ipv6 access-list To configure an IPv6 access control list (ACL) and enter IPv6-ACL configuration submode, use the ipv6 access-list command in configuration mode.
Page 677: Ipv6 Address
Chapter 11 I Commands ipv6 address S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ipv6 address To enable IPv6 processing and configure an IPv6 address on the interface, use the ipv6 address command in interface configuration submode.
Page 678 Chapter 11 I Commands ipv6 address S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ipv6 nd Configures IPv6 neighbor discovery commands on the interface.
Page 679: Ipv6 Address Autoconfig
Chapter 11 I Commands ipv6 address autoconfig S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ipv6 address autoconfig To enable automatic configuration of IPv6 addresses using stateless autoconfiguration on an interface and enable IPv6 processing on the interface, use the ipv6 address autoconfig command in interface...
Page 680: Ipv6 Enable
Chapter 11 I Commands ipv6 enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ipv6 enable To enable IPv6 processing and configure an IPv6 link-local address on the interface, use the ipv6 enable command in interface configuration submode.
Page 681 Chapter 11 I Commands ipv6 nd S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ipv6 nd To configure IPv6 neighbor discovery commands on the interface, use the ipv6 nd command in interface configuration submode.
Page 682 Chapter 11 I Commands ipv6 nd S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example sets the reachability time to 10000 milliseconds.
Page 683: Ipv6 Route
Chapter 11 I Commands ipv6 route S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ipv6 route To configure an IPv6 static route, use the ipv6 route command in configuration mode.
Page 684 Chapter 11 I Commands ipv6 route S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example configures a fully specified static route on a Gigabit Ethernet interface.
Page 685: Ipv6 Routing
Chapter 11 I Commands ipv6 routing S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ipv6 routing To enable IPv6 unicast routing, use the ipv6 routing command in configuration mode.
Page 686: Ipv6 Traffic-Filter
Chapter 11 I Commands ipv6 traffic-filter S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ipv6 traffic-filter To configure IPv6 access control lists (ACLs) to filter traffic for packets on the interface, use the ipv6 traffic-filter command in interface configuration submode.
Page 687: Iscsi Authentication
Chapter 11 I Commands iscsi authentication S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m iscsi authentication To configure the default authentication method for iSCSI, use the iscsi authentication command.
Page 688 Chapter 11 I Commands iscsi authentication S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch(config)# iscsi authentication chap Related Commands Command...
Page 689: Iscsi Duplicate-Wwn-Check
Chapter 11 I Commands iscsi duplicate-wwn-check S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m iscsi duplicate-wwn-check To check the current running configuration for conflicts between iSCSI initiators’...
Page 690 Chapter 11 I Commands iscsi duplicate-wwn-check S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch(config-iscsi-init)# no static pWWN 22:04:00:0d:ec:02:cb:02 Related Commands...
Page 691: Iscsi Dynamic Initiator
Chapter 11 I Commands iscsi dynamic initiator S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m iscsi dynamic initiator To configure dynamic initiator modes, use the iscsi dynamic initiator command in configuration mode.
Page 692 Chapter 11 I Commands iscsi dynamic initiator S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m This command is not supported on the Cisco MDS 9124 switch, the Cisco Fabric Switch for HP c-Class Note BladeSystem, and the Cisco Fabric Switch for IBM BladeCenter.
Page 693: Iscsi Enable
Chapter 11 I Commands iscsi enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m iscsi enable To enable the iSCSI feature in any Cisco MDS switch, issue the iscsi enable command.
Page 694: Iscsi Enable Module
Chapter 11 I Commands iscsi enable module S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m iscsi enable module To enable iSCSI features for each IPS linecard to create corresponding iSCSI interfaces, use the iscsi enable module command.
Page 695: Iscsi Import Target Fc
Chapter 11 I Commands iscsi import target fc S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m iscsi import target fc To allow dynamic mapping of Fibre Channel targets, use the iscsi import target fc command.
Page 696: Iscsi Initiator Idle-Timeout
Chapter 11 I Commands iscsi initiator idle-timeout S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m iscsi initiator idle-timeout To configure the iSCSI initiator idle timeout, use the iscsi initiator idle-timeout command.
Page 697: Iscsi Initiator Ip-Address
Chapter 11 I Commands iscsi initiator ip-address S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m iscsi initiator ip-address To assign persistent WWNs to an iSCSI initiator or assign an iSCSI initiator into VSANs other than the default VSAN, use the iscsi initiator ip-address command.
Page 698 Chapter 11 I Commands iscsi initiator ip-address S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch(config)# no iscsi initiator ip address 209.165.200.226 The following command uses the switch's WWN pool to allocate the nWWN for this iSCSI initiator and keeps it persistent.
Page 699: Iscsi Initiator Name
Chapter 11 I Commands iscsi initiator name S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m iscsi initiator name To configure an iSCSI initiator name and change to iSCSI configuration mode, use the iscsi initiator name command.
Page 700: Iscsi Interface Vsan-Membership
Chapter 11 I Commands iscsi interface vsan-membership S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m iscsi interface vsan-membership To configure VSAN membership for iSCSI interfaces, use the iscsi interface vsan-membership command.
Page 701 Chapter 11 I Commands iscsi interface vsan-membership S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command Description show iscsi initiator...
Page 702: Iscsi Save-Initiator
Chapter 11 I Commands iscsi save-initiator S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m iscsi save-initiator To permanently save the automatically-assigned nWWN/pWWN mapping, use the iscsi save-initiator command.
Page 703 Chapter 11 I Commands iscsi save-initiator S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 704: Iscsi Virtual-Target Name
Chapter 11 I Commands iscsi virtual-target name S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m iscsi virtual-target name To create a static iSCSI virtual target, use the iscsi virtual-target command.
Page 705 Chapter 11 I Commands iscsi virtual-target name S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Defaults Disabled.
Page 706 Chapter 11 I Commands iscsi virtual-target name S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch(config-iscsi-tgt)# initiator iqn.1987-02.com.cisco.initiator1 permit The following command prevents the specified initiator node from accessing virtual targets.
Page 707: Islb Abort
Chapter 11 I Commands islb abort S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m islb abort To discard a pending iSCSI Server Load Balancing (iSLB) configuration, use the islb abort command.
Page 708: Islb Commit
Chapter 11 I Commands islb commit S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m islb commit To commit a pending iSCSI server load balancing (iSLB) configuration, use the islb commit command.
Page 709: Islb Distribute
Chapter 11 I Commands islb distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m islb distribute To enable Cisco Fabric Services for iSCSI Server Load Balancing (iSLB) configuration, use the islb distribute command.
Page 710 Chapter 11 I Commands islb distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 711: Islb Initiator
Chapter 11 I Commands islb initiator S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m islb initiator To configure the iSCSI server load balancing (iSLB) initiator and enter iSLB initiator configuration submode, use the islb initiator command.
Page 712 Chapter 11 I Commands islb initiator S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example enters iSLB initiator configuration submode to configure static mapping (using the name option) for an iSLB initiator.
Page 713: Islb Save-Initiator
Chapter 11 I Commands islb save-initiator S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m islb save-initiator To permanently save the automatically-assigned nWWN/pWWN mapping for the iSLB initiator, use the islb save-initiator command.
Page 714 Chapter 11 I Commands islb save-initiator S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example saves the nWWNs and pWWNs that have automatically been assigned to all the iSLB initiators.
Page 715: Islb Virtual-Target Name
Chapter 11 I Commands islb virtual-target name S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m islb virtual-target name To configure an iSLB virtual target and enter iSLB target configuration submode, use the islb virtual-target name command.
Page 716 Chapter 11 I Commands islb virtual-target name S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Examples The following example creates a static virtual target and enters iSLB target configuration submode.
Page 717: Islb Vrrp
Chapter 11 I Commands islb vrrp S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m islb vrrp To configure iSCSI server load balancing (iSLB) on a Virtual Router Redundancy Protocol (VRRP) group, use the islb vrrp command.
Page 718 Chapter 11 I Commands islb vrrp S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m A Gigabit Ethernet interface configured for iSLB can only be in one VRRP group because redirected Caution sessions do not carry information about the VRRP IP address or group.
Page 719: Islb Zoneset Activate
Chapter 11 I Commands islb zoneset activate S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m islb zoneset activate To activate iSCSI server load balancing (iSLB) auto zones, use the islb zoneset activate command.
Page 720: Isns
Chapter 11 I Commands isns S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m isns To tag a Gigabit Ethernet or PortChannel interface to an Internet Storage Name Service (iSNS) profile, use the isns command in interface configuration submode.
Page 721 Chapter 11 I Commands isns S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command Description show interface port-channel...
Page 722: Isns Distribute
Chapter 11 I Commands isns distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m isns distribute To enable Cisco Fabric Services (CFS) distribution for Internet Storage Name Service (iSNS), use the isns distribute command.
Page 723: Isns Esi Retries
Chapter 11 I Commands isns esi retries S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m isns esi retries To configure the number of entity status inquiry (ESI) retry attempts, use the isns esi retries command in configuration mode.
Page 724: Isns Profile Name
Chapter 11 I Commands isns profile name S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m isns profile name To create an Internet Storage Name Service (iSNS) profile and enter iSNS profile configuration submode, use the isns profile name command in configuration mode.
Page 725: Isns Reregister
Chapter 11 I Commands isns reregister S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m isns reregister To register all Internet Storage Name Service (iSNS) objects for an interface that is already tagged to an iSNS profile, use the isns register command.
Page 726: Isns-Server Enable
Chapter 11 I Commands isns-server enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m isns-server enable To enable the Internet Storage Name Service (iSNS) server, use the isns-server enable command in configuration mode.
Page 727: Ivr Abort
Chapter 11 I Commands ivr abort S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr abort To discard an Inter-VSAN Routing (IVR) CFS distribution session in progress, use the ivr abort command in configuration mode.
Page 728: Ivr Commit
Chapter 11 I Commands ivr commit S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr commit To apply the pending configuration pertaining to the Inter-VSAN Routing (IVR) Cisco Fabric Services (CFS) distribution session in progress in the fabric, use the ivr commit command in configuration...
Page 729: Ivr Copy Active-Service-Group User-Configured-Service-Group
Chapter 11 I Commands ivr copy active-service-group user-configured-service-group S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr copy active-service-group user-configured-service-group To copy the active service group to the user configured service group, use the ivr copy active-service-group user-configured-service-group command in EXEC mode.
Page 730: Ivr Copy Active-Topology User-Configured-Topology
Chapter 11 I Commands ivr copy active-topology user-configured-topology S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr copy active-topology user-configured-topology To copy the active inter-VSAN routing (IVR) VSAN topology to the user configured topology, use the ivr copy active-topology user-configured-topology command in EXEC mode.
Page 731: Ivr Copy Active-Zoneset Full-Zoneset
Chapter 11 I Commands ivr copy active-zoneset full-zoneset S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr copy active-zoneset full-zoneset To copy the active zone set to the full zone set, use the ivr copy active-zoneset full-zoneset command in EXEC mode.
Page 732: Ivr Copy Auto-Topology User-Configured-Topology
Chapter 11 I Commands ivr copy auto-topology user-configured-topology S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr copy auto-topology user-configured-topology To copy the automatically discovered inter-VSAN routing (IVR) VSAN topology to the user configured topology, use the ivr copy auto-topology user-configured-topology command in EXEC mode.
Page 733: Ivr Distribute
Chapter 11 I Commands ivr distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr distribute To enable Cisco Fabric Services (CFS) distribution for Inter-VSAN Routing (IVR), use the ivr distribute command.
Page 734: Ivr Enable
Chapter 11 I Commands ivr enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr enable To enable the Inter-VSAN Routing (IVR) feature, use the ivr enable command in configuration mode.
Page 735: Ivr Fcdomain Database Autonomous-Fabric-Num
Chapter 11 I Commands ivr fcdomain database autonomous-fabric-num S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr fcdomain database autonomous-fabric-num To create IVR persistent FC IDs, use the ivr fcdomain database autonomous-fabric-num command.
Page 736 Chapter 11 I Commands ivr nat S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr nat To explicitly enable Network Address Translation (NAT) functionality for Inter-VSAN Routing (IVR), use the ivr nat command in configuration mode.
Page 737: Ivr Refresh
Chapter 11 I Commands ivr refresh S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr refresh To refresh devices being advertised by Inter-VSAN Routing (IVR), use the ivr refresh command in EXEC mode.
Page 738: Ivr Service-Group Activate
Chapter 11 I Commands ivr service-group activate S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr service-group activate To activate an inter-VSAN routing (IVR) service group, use the ivr service-group activate command in configuration mode.
Page 739 Chapter 11 I Commands ivr service-group activate S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 740: Ivr Service-Group Name
Chapter 11 I Commands ivr service-group name S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr service-group name To configure an Inter-VSAN Routing (IVR) service group, use the ivr service-group name command in configuration mode.
Page 741 Chapter 11 I Commands ivr service-group name S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch(config-ivr-sg)# Related Commands Command...
Page 742: Ivr Virtual-Fcdomain-Add
Chapter 11 I Commands ivr virtual-fcdomain-add S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr virtual-fcdomain-add To add the Inter-VSAN Routing (IVR) virtual domains in a specific VSAN(s) to the assigned domains list in that VSAN, use the ivr virtual-fcdomain-add command.
Page 743: Ivr Virtual-Fcdomain-Add2
Chapter 11 I Commands ivr virtual-fcdomain-add2 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr virtual-fcdomain-add2 To configure the request domain_ID (RDI) mode in a specific autonomous fabric ID (AFID) and VSAN for all IVR-enabled switches, use the ivr virtual-fcdomain-add2 command.
Page 744: Ivr Vsan-Topology
Chapter 11 I Commands ivr vsan-topology S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr vsan-topology To configure manual or automatic discovery of the Inter-VSAN Routing (IVR) topology, use the ivr vsan-topology command in configuration mode.
Page 745 Chapter 11 I Commands ivr vsan-topology S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 746: Ivr Vsan-Topology Database
Chapter 11 I Commands ivr vsan-topology database S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr vsan-topology database To configure an Inter-VSAN Routing (IVR) topology database, use the ivr vsan-topology database command in configuration mode.
Page 747 Chapter 11 I Commands ivr vsan-topology database S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Examples The following command enters configuration mode, enables the IVR feature, enters the VSAN topology database, and configures the pWWN-VSAN association for VSANs 2 and 2000:...
Page 748: Ivr Withdraw Domain
Chapter 11 I Commands ivr withdraw domain S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr withdraw domain To withdraw overlapping virtual domain from a specified VSAN, use the ivr withdraw domain command in EXEC mode.
Page 749: Ivr Zone Name
Chapter 11 I Commands ivr zone name S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr zone name To configure a zone for Inter-VSAN Routing (IVR), use the ivr zone name command.
Page 750: Ivr Zone Rename
Chapter 11 I Commands ivr zone rename S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr zone rename To rename an inter-VSAN routing (IVR) zone, use the ivr zone rename command.
Page 751: Ivr Zoneset
Chapter 11 I Commands ivr zoneset S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr zoneset To configure a zoneset for Inter-VSAN Routing (IVR), use the ivr zoneset command.
Page 752: Ivr Zoneset Rename
Chapter 11 I Commands ivr zoneset rename S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ivr zoneset rename To rename an inter-VSAN routing (IVR) zone set, use the ivr zoneset rename command.
Page 753 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C H A P T E R J Commands The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric...
Page 754: Chapter 12 J Command
Chapter 12 J Commands job name S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m job name To assign a job to a command schedule, use the job name command.
Page 755 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C H A P T E R K Commands The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric...
Page 756: Chapter 13 K Command
Chapter 13 K Commands keepalive S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m keepalive To configure the message keepalive interval for the IKE protocol, use the keepalive command in IKE configuration submode.
Page 757: Kernel Core
Chapter 13 K Commands kernel core S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m kernel core Use the kernel core command to generate a core dump for each module.
Page 758: Kernel Core
Chapter 13 K Commands kernel core S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example configures module 5 to generate only header-level cores: switch(config)# kernel core module 5 level header succeeded...
Page 759 Chapter 13 K Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m To configure the preshared key for the IKE protocol, use the key command in IKE configuration submode.
Page 760 Chapter 13 K Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 761 Chapter 13 K Commands key-ontape S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m key-ontape To configure keys on the tape mode and store the encrypted security keys on the backup tapes, use the key-ontape command.
Page 762: Key-Ontape
Chapter 13 K Commands key-ontape S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 763 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C H A P T E R L Commands The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric...
Page 764: Chapter 14 L Command
Chapter 14 L Commands lifetime seconds S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m lifetime seconds To configure the security association (SA) lifetime duration for an IKE protocol policy, use the lifetime seconds command in IKE policy configuration submode.
Page 765: Line Com1
Chapter 14 L Commands line com1 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m line com1 To configure auxiliary COM 1 port, use the line com1 command.
Page 766 Chapter 14 L Commands line com1 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command Modes Configuration mode.
Page 767 Chapter 14 L Commands line com1 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example assigns the user-specified initialization string for a Supervisor-2 module to its corresponding profile: switch# config terminal...
Page 768: Line Console
Chapter 14 L Commands line console S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m line console To configure a terminal line, use the line console command.
Page 769 Chapter 14 L Commands line console S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Parity none.
Page 770 Chapter 14 L Commands line console S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example deletes the configured initialization string: switch# config terminal switch(config)# line console...
Page 771: Line Vty
Chapter 14 L Commands line vty S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m line vty To configure a virtual terminal line, use the line vty command.
Page 772: Link (Sdv Virtual Device Configuration Submode)
Chapter 14 L Commands link (SDV virtual device configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m link (SDV virtual device configuration submode) To link a virtual device to a real device, use the link command in SDV virtual device configuration submode.
Page 773: Link-State-Trap
Chapter 14 L Commands link-state-trap S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m link-state-trap To enable an SNMP link state trap on an interface, use the link-state-trap command in interface configuration submode.
Page 774: Link-State-Trap (Sme)
Chapter 14 L Commands link-state-trap (SME) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m link-state-trap (SME) To enable an Simple Network Management Protocol (SNMP) link state trap on an interface, use the link-state-trap command.
Page 775: Load-Balancing
Chapter 14 L Commands load-balancing S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m load-balancing To enable cluster reload balancing for all targets or specific targets, use the load-balancing command.
Page 776: Logging Abort
Chapter 14 L Commands logging abort S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m logging abort To discard the logging Cisco Fabric Services (CFS) distribution session in progress, use the logging abort command in configuration mode.
Page 777: Logging Commit
Chapter 14 L Commands logging commit S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m logging commit To apply the pending configuration pertaining to the logging Cisco Fabric Services (CFS) distribution session in progress in the fabric, use the logging commit command in configuration mode.
Page 778: Logging Console
Chapter 14 L Commands logging console S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m logging console To set console logging, use the logging console command.
Page 779: Logging Distribute
Chapter 14 L Commands logging distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m logging distribute To enable Cisco Fabric Services (CFS) distribution for logging, use the logging distribute command.
Page 780: Logging Level
Chapter 14 L Commands logging level S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m logging level To modify message logging facilities, use the logging level command.
Page 781: Logging Logfile
Chapter 14 L Commands logging logfile S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m logging logfile To set message logging for logfile, use the logging logfile command.To negate the previously issued command or to revert to factory defaults, use the no form of the command.
Page 782: Logging Module
Chapter 14 L Commands logging module S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m logging module To set message logging for linecards, use the logging module command.
Page 783: Logging Monitor
Chapter 14 L Commands logging monitor S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m logging monitor To set monitor message logging, use the logging monitor command.
Page 784: Logging Server
Chapter 14 L Commands logging server S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m logging server To set message logging for the remote server, use the logging server command.
Page 785 Chapter 14 L Commands logging server S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command History Release Modification...
Page 786: Logging Timestamp
Chapter 14 L Commands logging timestamp S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m logging timestamp To set the time increment for the message logging time stamp, use the logging timestamp command.
Page 787 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C H A P T E R M Commands The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric...
Page 788: Chapter 15 M Command
Chapter 15 M Commands match S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m match To configure QoS class map match criteria, use the match command in class map configuration submode.
Page 789: Match
Chapter 15 M Commands match S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch(config)# qos class-map MyClass1 match-any switch(config-cmap)# match any The following example specifies a destination address match for frames with the specified destination...
Page 790: Match Address
Chapter 15 M Commands match address S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m match address To configure match addresses in an IPsec crypto map with an access control list (ACL), use the match address command in IPsec crypto map configuration submode.
Page 791: Mcast Root
Chapter 15 M Commands mcast root S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m mcast root To configure the multicast feature, use the mcast root command in configuration mode.
Page 792 Chapter 15 M Commands member (fcalias configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m member (fcalias configuration submode) To add a member name to an Fibre Channel alias on a VSAN, use the member command in fcalias configuration submode.
Page 793: Member (Fcalias Configuration Submode)
Chapter 15 M Commands member (fcalias configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command History Release Modification...
Page 794 Chapter 15 M Commands member (ivr zone configuration) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m member (ivr zone configuration) To add a member name to an Inter-VSAN Routing (IVR) zone, use the member command in IVR zone configuration submode.
Page 795: Member (Ivr Zone Configuration)
Chapter 15 M Commands member (ivr zone configuration) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch# config terminal Enter configuration commands, one per line.
Page 796 Chapter 15 M Commands member (zone configuration and zoneset-zone configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m member (zone configuration and zoneset-zone configuration submode) To add a member name to a Fibre Channel zone set zone member, use the member command in zone set...
Page 797: Member (Zone Configuration And Zoneset-Zone Configuration Submode)
Chapter 15 M Commands member (zone configuration and zoneset-zone configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command History Release Modification...
Page 798: Member (Zoneset Configuration Submode)
Chapter 15 M Commands member (zoneset configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m member (zoneset configuration submode) To configure zone set zone members, use the member command in zone set configuration submode.
Page 799: Metric (Islb Initiator Configuration)
Chapter 15 M Commands metric (iSLB initiator configuration) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m metric (iSLB initiator configuration) To assign a load-balancing metric for an iSLB initiator, use the metric command in iSLB initiator configuration submode.
Page 800: Mkdir
Chapter 15 M Commands mkdir S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m mkdir To create a directory in the Flash file system, use the mkdir command in EXEC mode.
Page 801: Modem Connect Line
Chapter 15 M Commands modem connect line S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m modem connect line To enable a modem connection when the switch is already in operation, use the modem connect line command in EXEC mode.
Page 802 Chapter 15 M Commands move S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m move To remove a file from the source file and place it in the destination file, use the move command in EXEC mode.
Page 803: Move
Chapter 15 M Commands mutual-chap username (iSCSI initiator configuration and iSLB initiator configuration) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m mutual-chap username (iSCSI initiator configuration and iSLB initiator configuration) To assign a username for the initiator’s challenge, use the mutual-chap command in iSCSI initiator...
Page 804: Mutual-Chap Username (Iscsi Initiator Configuration And Islb Initiator Configuration)
Chapter 15 M Commands mutual-chap username (iSCSI initiator configuration and iSLB initiator configuration) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example assigns a username and password to the initiator’s challenge for an iSLB initiator: switch# config t...
Page 805 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C H A P T E R N Commands The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric...
Page 806: Chapter 16 N Command
Chapter 16 N Commands native-autonomous-fabric-num S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m native-autonomous-fabric-num To create an IVR persistent FC ID database entry, use the native-autonomous-fabric-num command in fcdomain database configuration submode.
Page 807: Node
Chapter 16 N Commands node S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m node To configure Cisco SME switch, use the node command.
Page 808: No Fc-Redirect Version2 Enable
Chapter 16 N Commands no fc-redirect version2 enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m no fc-redirect version2 enable To disable the version2 mode in FC-Redirect, use the no fc-redirect version2 enable command in configuration mode.
Page 809 Chapter 16 N Commands no fc-redirect version2 enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 810: Npiv Enable
Chapter 16 N Commands npiv enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m npiv enable To enable N Port Identifier Virtualization (NPIV) for all VSANs on a switch, use the npiv enable command in configuration mode.
Page 811: Nport Pwwn
Chapter 16 N Commands nport pwwn S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m nport pwwn To configure the nport pWWN for the SAN extension tuner, use the nport pwwn command in SAN extension configuration mode.
Page 812: Npv Enable
Chapter 16 N Commands npv enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m npv enable To enable N Port Virtualization (NPV), use the npv enable command in configuration mode.
Page 813: Npv Auto-Load-Balance Disruptive
Chapter 16 N Commands npv auto-load-balance disruptive S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m npv auto-load-balance disruptive To enable autoload balance disruptive, use the npv auto-load-balance disruptive command in configuration mode.
Page 814: Npv Traffic-Map Server-Interface
Chapter 16 N Commands npv traffic-map server-interface S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m npv traffic-map server-interface To configure the server interface based trafic engineering, use the npv traffic-map server-interface command in configuration mode.
Page 815 Chapter 16 N Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m To configure NTP settings on the switch, use the ntp command in configuration mode.
Page 816: Ntp Abort
Chapter 16 N Commands ntp abort S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ntp abort To discard the Network Time Protocol (NTP) Cisco Fabric Services (CFS) distribution session in progress, use the ntp abort command in configuration mode.
Page 817: Ntp Commit
Chapter 16 N Commands ntp commit S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ntp commit To apply the pending configuration pertaining to the Network Time Protocol (NTP) Cisco Fabric Services (CFS) distribution session in progress in the fabric, use the ntp commit command in...
Page 818: Ntp Distribute
Chapter 16 N Commands ntp distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ntp distribute To enable Cisco Fabric Services (CFS) distribution for Network Time Protocol (NTP), use the ntp distribute command.
Page 819: Ntp Sync-Retry
Chapter 16 N Commands ntp sync-retry S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ntp sync-retry To retry synchronization with configured servers, use the ntp sync-retry command.
Page 820: Nwwn (Dpvm Database Configuration Submode)
Chapter 16 N Commands nwwn (DPVM database configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m nwwn (DPVM database configuration submode) To add a device to a dynamic port VSAN membership (DPVM) database using the nWWN, use the nwwn command in DPVM database configuration submode.
Page 821: Nwwn (San Extension Configuration Mode)
Chapter 16 N Commands nwwn (SAN extension configuration mode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m nwwn (SAN extension configuration mode) To configure the nWWN for the SAN extension tuner, use the nwwn command in SAN extension configuration submode.
Page 822 Chapter 16 N Commands nwwn (SAN extension configuration mode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Cisco MDS 9000 Family Command Reference 16-18 OL-18089-01, Cisco MDS NX-OS Release 4.x...
Page 823 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C H A P T E R O Commands The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric...
Page 824: Chapter 17 O Command
Chapter 17 O Commands odrt.bin S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m odrt.bin To preform offline data recovery of Cisco SME, use the odrt.bin command on Linux-based systems.
Page 825: Odrt.bin
Chapter 17 O Commands odrt.bin S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m odrt -h if=/dev/sg0 The following example read the data on tape into intermediate file(s) on disk: odrt -r if=/dev/sg0 of=diskfile...
Page 826: Ocsp Url
Chapter 17 O Commands ocsp url S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ocsp url To configure the HTTP URL of the Online Certificate Status Protocol (OCSP) for the trust point CA, use the ocsp url command in trust point configuration submode.
Page 827: Ocsp Url
Chapter 17 O Commands ocsp url S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 828 Chapter 17 O Commands out-of-service S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m out-of-service To put an interface out of service, use the out-of-service command in interface configuration submode.
Page 829: Out-Of-Service
Chapter 17 O Commands out-of-service S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 830: Out-Of-Service Module
Chapter 17 O Commands out-of-service module S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m out-of-service module To perform a graceful shutdown of an integrated crossbar on the supervisor module of a Cisco MDS 9500 Series Director, use the out-of-service module command in EXEC mode.
Page 831 Chapter 17 O Commands out-of-service xbar S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m out-of-service xbar To perform a graceful shutdown of the external crossbar switching module of a Cisco MDS 9513 Director, use the out-of-service xbar command in EXEC mode.
Page 832: Out-Of-Service Xbar
Chapter 17 O Commands out-of-service xbar S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 833 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C H A P T E R P Commands The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric...
Page 834: Chapter 18 P Command
Chapter 18 P Commands passive-mode S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m passive-mode To configure the required mode to initiate an IP connection, use the passive-mode command.
Page 835: Peer (Dmm Job Configuration Submode)
Chapter 18 P Commands peer (DMM job configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m peer (DMM job configuration submode) To add peer SSM information to a job, use the peer command in DMM job configuration submode.
Page 836: Peer-Info Ipaddr
Chapter 18 P Commands peer-info ipaddr S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m peer-info ipaddr To configure the peer information for the FCIP interface, use the peer-info ipaddr command.
Page 837 Chapter 18 P Commands peer-info ipaddr S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 838: Periodic-Inventory Notification
Chapter 18 P Commands periodic-inventory notification S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m periodic-inventory notification To enable the periodic inventory notification message dispatches, use the periodic-inventory notification command Call Home configuration submode.
Page 839: Permit (Ipv6-Acl Configuration)
Chapter 18 P Commands permit (IPv6-ACL configuration) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m permit (IPv6-ACL configuration) To configure permit conditions for an IPv6 access control list (ACL), use the permit command in IPv6-ACL configuration submode.
Page 840 Chapter 18 P Commands permit (IPv6-ACL configuration) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m icmp Applies the ACL to any Internet Control Message Protocol (ICMP) packet.
Page 841 Chapter 18 P Commands permit (IPv6-ACL configuration) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Examples The following example configures an IPv6-ACL called List, enters IPv6-ACL submode, and adds an entry that permits IPv6 traffic from any source address to any destination address.
Page 842: Phone-Contact
Chapter 18 P Commands phone-contact S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m phone-contact To configure the telephone contact number with the Call Home function, use the phone-contact command in Call Home configuration submode.
Page 843: Ping
Chapter 18 P Commands ping S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m ping To diagnose basic network connectivity, use the ping command in EXEC mode.
Page 844 Chapter 18 P Commands ping S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m --- 209.165.200.226 ping statistics --- 13 packets transmitted, 13 packets received, 0% packet loss round-trip min/avg/max = 0.2/0.2/0.4 ms...
Page 845: Policy
Chapter 18 P Commands policy S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m policy To enter IKE policy configuration and configure a policy for the IKE protocol, use the policy command in IKE configuration submode.
Page 846: Port
Chapter 18 P Commands port S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m port To assign the TCP port number of a Gigabit Ethernet interface to the FCIP profile or a listener peer port for a ISCSI interface, use the port command.
Page 847: Port-Channel Persistent
Chapter 18 P Commands port-channel persistent S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m port-channel persistent To convert an automatically created PortChannel to a persistent PortChannel, use the port-channel persistent command in EXEC mode.
Page 848: Port-License
Chapter 18 P Commands port-license S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m port-license To make a port eligible or ineligible to acquire a port activation license on a Cisco MDS 9124 switch, use the port-license command.
Page 849: Port-Monitor Activate
Chapter 18 P Commands port-monitor activate S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m port-monitor activate To activate the specified port monitor policy, use port-monitor activate command.
Page 850: Port-Monitor Enable
Chapter 18 P Commands port-monitor enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m port-monitor enable To enable the user to activate or deactivate policies, use the port-monitor enable command.
Page 851: Port-Monitor Name
Chapter 18 P Commands port-monitor name S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m port-monitor name To display the counter details of the policy, use the port-monitor name command.
Page 852: Port-Security
Chapter 18 P Commands port-security S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m port-security To configure port security features and reject intrusion attempts, use the port-security command in configuration mode.
Page 853 Chapter 18 P Commands port-security S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command History Release Modification...
Page 854 Chapter 18 P Commands port-security S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch(config-port-security)# no pwwn 20:11:00:33:11:00:2a:4a fwwn 20:81:00:44:22:00:4a:9e The following example configures the specified pWWN to only log in through the specified sWWN.
Page 855: Port-Security Abort
Chapter 18 P Commands port-security abort S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m port-security abort To discard the port security Cisco Fabric Services (CFS) distribution session in progress, use the port-security abort command in configuration mode.
Page 856: Port-Security Commit
Chapter 18 P Commands port-security commit S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m port-security commit To apply the pending configuration pertaining to the port security Cisco Fabric Services (CFS) distribution session in progress in the fabric, use the port-security commit command in configuration...
Page 857: Port-Security Database
Chapter 18 P Commands port-security database S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m port-security database To copy the port security database or to view the difference within the port security database, use the port-security database command in EXEC mode.
Page 858 Chapter 18 P Commands port-security database S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 859: Port-Security Distribute
Chapter 18 P Commands port-security distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m port-security distribute To enable Cisco Fabric Services (CFS) distribution for port security, use the port-security distribute command.
Page 860: Port-Security Enable
Chapter 18 P Commands port-security enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m port-security enable To enable port security, use the port-security enable command in configuration mode.
Page 861: Port-Track Enable
Chapter 18 P Commands port-track enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m port-track enable To enable port tracking for indirect errors, use the port-track enable command in configuration mode.
Page 862: Port-Track Force-Shut
Chapter 18 P Commands port-track force-shut S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m port-track force-shut To force a shutdown of a tracked port, use the port-track force-shut command in interface configuration submode.
Page 863: Port-Track Interface
Chapter 18 P Commands port-track interface S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m port-track interface To enable port tracking for specific interfaces, use the port-track interface command in interface configuration submode.
Page 864 Chapter 18 P Commands port-track interface S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command Description show interface fc...
Page 865: Port-Type
Chapter 18 P Commands port-type S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m port-type To configure port type policies, use port-type command.
Page 866 Chapter 18 P Commands port-type S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 867: Portaddress
Chapter 18 P Commands portaddress S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m portaddress To enable the FICON feature in a specified VSAN, use the ficon vsan command in configuration mode.
Page 868 Chapter 18 P Commands portaddress S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example enables the selected port address and reverts to the factory default of the port address not being blocked.
Page 869: Power Redundancy-Mode
Chapter 18 P Commands power redundancy-mode S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m power redundancy-mode To configure the capacity of the power supplies on the Cisco MDS 9500 Family of switches, use the power redundancy-mode command in configuration mode.
Page 870 Chapter 18 P Commands power redundancy-mode S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 871: Poweroff Module
Chapter 18 P Commands poweroff module S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m poweroff module To power off individual modules in the system, use the poweroff module command in configuration mode.
Page 872: Priority
Chapter 18 P Commands priority S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m priority To configure the priority in a QoS policy map class, use the priority command in QoS policy class map configuration submode.
Page 873 Chapter 18 P Commands priority S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command Description class...
Page 874: Purge Fcdomain Fcid
Chapter 18 P Commands purge fcdomain fcid S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m purge fcdomain fcid To purge persistent FCIDs, use the purge fcdomain fcid command in EXEC mode.
Page 875: Purge Module
Chapter 18 P Commands purge module S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m purge module To delete configurations in the running configuration for nonexistent modules, use the purge module command in EXEC mode.
Page 876 Chapter 18 P Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m To view your present working context (PWC), use the pwc command in any mode.
Page 877 Chapter 18 P Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m To display the current directory location, use the pwd command in EXEC mode.
Page 878: Pwwn (Dpvm Database Configuration Submode)
Chapter 18 P Commands pwwn (DPVM database configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m pwwn (DPVM database configuration submode) To add a device to a dynamic port VSAN membership (DPVM) database using the pWWN, use the pwwn command in DPVM database configuration submode.
Page 879: Pwwn (Fcdomain Database Configuration Submode)
Chapter 18 P Commands pwwn (fcdomain database configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m pwwn (fcdomain database configuration submode) To map a pWWN to a persistent FC ID for IVR, use the pwwn command in IVR fcdomain database configuration submode.
Page 880: Pwwn (Sdv Virtual Device Configuration Submode)
Chapter 18 P Commands pwwn (SDV virtual device configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m pwwn (SDV virtual device configuration submode) To add a pWWN to a virtual device, use the pwwn command in SDV virtual device configuration submode.
Page 881 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C H A P T E R Q Commands The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric...
Page 882: Chapter 19 Q Command
Chapter 19 Q Commands qos class-map S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m qos class-map To create and define a traffic class with match criteria that will be used to identify traffic, use the qos class-map command in configuration mode.
Page 883: Qos Control Priority
Chapter 19 Q Commands qos control priority S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m qos control priority To enable the QoS priority assignment for control traffic feature on the Cisco MDS 9000 family of switches, use the qos control command in configuration mode.
Page 884: Qos Dwrr-Q
Chapter 19 Q Commands qos dwrr-q S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m qos dwrr-q To associate a weight with a deficit weighted round robin (DWRR) scheduler queue, use the qos dwrr-q command in configuration mode.
Page 885: Qos Enable
Chapter 19 Q Commands qos enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m qos enable To enable the QoS priority assignment for data traffic feature on the Cisco MDS 9000 family of switches, use the qos enable command in configuration mode.
Page 886: Qos Policy-Map
Chapter 19 Q Commands qos policy-map S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m qos policy-map To specify the class of service, use the qos policy-map command in configuration mode.
Page 887: Qos Priority
Chapter 19 Q Commands qos priority S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m qos priority To configure the quality of server (QoS) priority attribute in a zone attribute group, use the qos priority command in zone attribute configuration submode.
Page 888: Qos Service
Chapter 19 Q Commands qos service S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m qos service To apply a service policy, use the qos service command in configuration mode.
Page 889: Quiesce
Chapter 19 Q Commands quiesce S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m quiesce To gracefully shut down an ISL in a PortChannel, use the quiesce command in configuration mode.
Page 890 Chapter 19 Q Commands quiesce S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Cisco MDS 9000 Family Command Reference 19-10 OL-18089-01 Cisco MDS NX-OS Release 4.x...
Page 891 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C H A P T E R R Commands The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric...
Page 892: Chapter 20 R Command
Chapter 20 R Commands radius abort S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m radius abort To discard a RADIUS Cisco Fabric Services (CFS) distribution session in progress, use the radius abort command in configuration mode.
Page 893: Radius Commit
Chapter 20 R Commands radius commit S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m radius commit To apply the pending configuration pertaining to the RADIUS Cisco Fabric Services (CFS) distribution session in progress in the fabric, use the radius commit command in configuration mode.
Page 894: Radius Commit
Chapter 20 R Commands radius distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m radius distribute To enable Cisco Fabric Services (CFS) distribution for RADIUS, use the radius distribute command.
Page 895: Radius-Server Deadtime
Chapter 20 R Commands radius-server deadtime S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m radius-server deadtime To set a periodic time interval where a nonreachable (nonresponsive) RADIUS server is monitored for responsiveness, use the radius-server deadtime command.
Page 896: Radius-Server Directed-Request
Chapter 20 R Commands radius-server directed-request S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m radius-server directed-request To specify a RADIUS server to send authentication requests to when logging in, use the radius-server directed-request command.
Page 897 Chapter 20 R Commands radius-server host S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m radius-server host To configure RADIUS server parameters, use the radius-server host command.
Page 898: Radius-Server Host
Chapter 20 R Commands radius-server host S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Defaults Idle-time is not set.
Page 899: Radius-Server Key
Chapter 20 R Commands radius-server key S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m radius-server key To configure a global RADIUS shared secret, use the radius-server key command.
Page 900: Radius-Server Retransmit
Chapter 20 R Commands radius-server retransmit S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m radius-server retransmit To globally specify the number of times the switch should try a request with a RADIUS server, use the radius-server retransmit command.
Page 901: Radius-Server Timeout
Chapter 20 R Commands radius-server timeout S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m radius-server timeout To specify the time between retransmissions to the RADIUS servers, use the radius-server timeout command.
Page 902: Rate-Mode Bandwidth-Fairness
Chapter 20 R Commands rate-mode bandwidth-fairness S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m rate-mode bandwidth-fairness To enable or disable bandwidth fairness among ports in a port group, use the rate-mode bandwidth-fairness command in configuration mode.
Page 903 Chapter 20 R Commands rate-mode oversubscription-limit S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m rate-mode oversubscription-limit To enable or disable restrictions on oversubscription ratios, use the rate-mode oversubscription-limit command.
Page 904: Rate-Mode Oversubscription-Limit
Chapter 20 R Commands rate-mode oversubscription-limit S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m interface fc2/1 Related Commands Command...
Page 905 Chapter 20 R Commands reload S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m reload To reload the entire switch, an active supervisor module, a standby supervisor module, or a specific module, or to force a netboot on a given module, use the reload command in EXEC mode.
Page 906: Reload
Chapter 20 R Commands reload S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 907 Chapter 20 R Commands read command-id S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m read command-id To configure a SCSI read command for a SAN tuner extension N port, use the read command-id command.
Page 908: Read Command-Id
Chapter 20 R Commands read command-id S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command Description show san-ext-tuner...
Page 909: Read-Only
Chapter 20 R Commands read-only S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m read-only To configure the read-only attribute in a zone attribute group, use the read-only command in zone attribute configuration submode.
Page 910 Chapter 20 R Commands revocation-check S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m revocation-check To configure trust point revocation check methods, use the revocation-check command in trust point configuration submode.
Page 911: Revocation-Check
Chapter 20 R Commands revocation-check S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example shows how to check revocation status first using locally cached CRL and then, if needed, using OCSP.
Page 912 Chapter 20 R Commands rlir preferred-cond fcid S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m rlir preferred-cond fcid To specify a preferred host to receive Registered Link Incident Report (RLIR) frames, use the rlir preferred-cond fcid command in configuration mode.
Page 913: Rlir Preferred-Cond Fcid
Chapter 20 R Commands rlir preferred-cond fcid S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 914: Rmdir
Chapter 20 R Commands rmdir S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m rmdir To delete an existing directory from the Flash file system, use the rmdir command in EXEC mode.
Page 915: Rmon Alarm
Chapter 20 R Commands rmon alarm S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m rmon alarm To configure a 32- bit remote monitoring (RMON) alarm, use the rmon alarm command in configuration mode.
Page 916: Rmon Alarm
Chapter 20 R Commands rmon alarm S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Examples The following example configures a 32-bit alarm number 20 for ifInErrors (OID 1.3.6.1.2.1.2.2.1.14) on interface fc 1/1.
Page 917: Rmon Event
Chapter 20 R Commands rmon event S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m rmon event To configure a remote monitoring (RMON) event, use the rmon event command in configuration mode.
Page 918: Rmon Event
Chapter 20 R Commands rmon event S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch(config)# The following example configures RMON event3 to log the onboard RMONlog and send an SNMP trap to public community trap destinations.
Page 919: Rmon Hcalarm
Chapter 20 R Commands rmon hcalarm S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m rmon hcalarm To configure a 64-bit remote monitoring (RMON) high-capacity alarm (hcalarm), use the rmon hcalarm command in configuration mode.
Page 920: Rmon Hcalarm
Chapter 20 R Commands rmon hcalarm S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Usage Guidelines Event number 0 is a predefined null (or no operation) event.
Page 921: Role Abort
Chapter 20 R Commands role abort S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m role abort To discard an authorization role Cisco Fabric Services (CFS) distribution session in progress, use the role abort command in configuration mode.
Page 922: Role Commit
Chapter 20 R Commands role commit S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m role commit To apply the pending configuration pertaining to the authorization role Cisco Fabric Services (CFS) distribution session in progress in the fabric, use the role commit command in configuration mode.
Page 923: Role Commit
Chapter 20 R Commands role distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m role distribute To enable Cisco Fabric Services (CFS) distribution for authorization roles, use the role distribute command.
Page 924: Role Name
Chapter 20 R Commands role name S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m role name To configure and assign users to a new role or to modify the profile for an existing role, use the role name command in configuration mode.
Page 925: Role Name
Chapter 20 R Commands role name S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Usage Guidelines Roles are assigned rules.
Page 926 Chapter 20 R Commands rsakeypair S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m rsakeypair To configure and associate the RSA key pair details to a trust point, use the rsakeypair command in trust point configuration submode.
Page 927: Rsakeypair
Chapter 20 R Commands rsakeypair S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 928 Chapter 20 R Commands rscn S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m rscn To configure a registered state change notification (RSCN), a Fibre Channel service that informs Nx ports about changes in the fabric, use the rscn command in configuration mode.
Page 929: Rscn
Chapter 20 R Commands rscn abort vsan S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m rscn abort vsan To cancel a Registered State Change Notification (RSCN) configuration on a VSAN, use the rscn abort vsan command in configuration mode.
Page 930: Rscn Abort Vsan
Chapter 20 R Commands rscn commit vsan S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m rscn commit vsan To apply a pending Registered State Change Notification (RSCN) configuration, use the rscn commit vsan command in configuration mode.
Page 931: Rscn Commit Vsan
Chapter 20 R Commands rscn distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m rscn distribute To enable distribution of a Registered State Change Notification (RSCN) configuration, use the rscn distribute command in configuration mode.
Page 932: Rscn Distribute
Chapter 20 R Commands rscn event-tov S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m rscn event-tov To configure an event timeout value for a Registered State Change Notification (RSCN) on a specified VSAN, use the rscn event-tov command in configuration mode.
Page 933: Rscn Event-Tov
Chapter 20 R Commands rscn event-tov S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 934: Rule
Chapter 20 R Commands rule S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m rule To specify the tape volume group regular expression, use the rule command.
Page 935 Chapter 20 R Commands run-script S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m run-script To execute the commands specified in a file, use the run-script command.
Page 936: Run-Script
Chapter 20 R Commands run-script S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m 'sh interface fc1/1' fc1/1 is down (Fcot not present) Hardware is Fibre Channel...
Page 937 Chapter 20 R Commands rspan-tunnel S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m rspan-tunnel To associate and bind the SPAN tunnel (ST) port with the RSPAN tunnel, use the rspan-tunnel command.
Page 938: Rspan-Tunnel
Chapter 20 R Commands rspan-tunnel S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Cisco MDS 9000 Family Command Reference 20-48 OL-18089-01, Cisco MDS NX-OS Release 4.x...
Page 939 S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m C H A P T E R S Commands The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric...
Page 940: Chapter 21 Command
Chapter 21 S Commands san-ext-tuner enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m san-ext-tuner enable To enable the IP Network Simulator to simulate a variety of data network conditions, use the san-ext-tuner enable command.
Page 941 Chapter 21 S Commands san-ext-tuner enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 942: Santap Module
Chapter 21 S Commands santap module S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m santap module To configure the mapping between the Storage Services Module (SSM) and the VSAN where the appliance is configured, use the santap module command in configuration mode.
Page 943 Chapter 21 S Commands santap module S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command History Release Modification...
Page 944: Scaling Batch Enable
Chapter 21 S Commands scaling batch enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m scaling batch enable To enable scalability in the Cisco SME configuration, use the scaling batch enable command.
Page 945: Scheduler
Chapter 21 S Commands scheduler S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m scheduler To schedule a maintenance job, use the scheduler command.
Page 946 Chapter 21 S Commands scheduler S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Examples The following example shows how to enable the scheduler command: switch# config t...
Page 947: Scheduler Aaa-Authentication
Chapter 21 S Commands scheduler aaa-authentication S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m scheduler aaa-authentication To use the command scheduler feature, a remote user must use the scheduler aaa-authentication command to specify an AAA authentication password.
Page 948 Chapter 21 S Commands scheduler aaa-authentication S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 949: Scsi-Flow Distribute
Chapter 21 S Commands scsi-flow distribute S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m scsi-flow distribute To enable SCSI flow distribution through CFS, use the scsi-flow distribute command.
Page 950: Scsi-Flow Flow-Id
Chapter 21 S Commands scsi-flow flow-id S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m scsi-flow flow-id To configure SCSI flow services, use the scsi-flow flow-id command.
Page 951 Chapter 21 S Commands scsi-flow flow-id S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m The following example disables a SCSI flow with a flow identifier of 4.
Page 952: Scsi-Target
Chapter 21 S Commands scsi-target S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m scsi-target To configure SCSI target discovery, use the scsi-target command in configuration mode.
Page 953 Chapter 21 S Commands scsi-target S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch# config t switch(config)# no scsi-target discovery The following example configures SCSI target ns-polling discovery for VSAN 1.
Page 954: Sdv Abort Vsan
Chapter 21 S Commands sdv abort vsan S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m sdv abort vsan To terminate an SDV configuration for a specified VSAN, use the sdv abort vsan command in configuration mode.
Page 955: Sdv Commit Vsan
Chapter 21 S Commands sdv commit vsan S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m sdv commit vsan To commit an SDV configuration to a specified VSAN, use the sdv commit vsan command in configuration mode.
Page 956: Sdv Enable
Chapter 21 S Commands sdv enable S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m sdv enable To enable SDV on the switch, use the sdv enable command in configuration mode.
Page 957: Sdv Virtual-Device Name
Chapter 21 S Commands sdv virtual-device name S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m sdv virtual-device name To create a virtual device name for a specified VSAN, use the sdv virtual-device name command in configuration mode.
Page 958: Security-Mode
Chapter 21 S Commands security-mode S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m security-mode To configure the Cisco SME security settings, use the security-mode command.
Page 959: Send
Chapter 21 S Commands send S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m send To send a message to all active CLI users currently using the switch, use the send command in EXEC mode.
Page 960: Server
Chapter 21 S Commands server S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m server To add a server in an Internet Storage Name Service (iSNS) profile, use the server command in iSNS profile configuration submode.
Page 961: Server (Configure Session Submode)
Chapter 21 S Commands server (configure session submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m server (configure session submode) To configure a data migration session, use the server command in session configuration submode.
Page 962: Server (Dmm Job Configuration Submode)
Chapter 21 S Commands server (DMM job configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m server (DMM job configuration submode) To add a server HBA port to the DMM job, use the server command in DMM job configuration submode.
Page 963: Server (Radius Configuration)
Chapter 21 S Commands server (radius configuration) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m server (radius configuration) To configure a RADIUS server, use the server command in RADIUS configuration submode.
Page 964: Server (Tacacs+ Configuration)
Chapter 21 S Commands server (tacacs+ configuration) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m server (tacacs+ configuration) To configure a TACACS+ server, use the server command in TACACS+ configuration submode.
Page 965: Set (Ipsec Crypto Map Configuration Submode)
Chapter 21 S Commands set (IPsec crypto map configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m set (IPsec crypto map configuration submode) To configure attributes for IPsec crypto map entries, use the set command in IPsec crytpo map configuration submode.
Page 966 Chapter 21 S Commands set (IPsec crypto map configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Command History Release Modification...
Page 967: Setup
Chapter 21 S Commands setup S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m setup To enter the switch setup mode, use the setup command in EXEC mode.
Page 968: Setup
Chapter 21 S Commands setup S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m setup To run the basic setup facility, use the setup command.
Page 969: Setup Ficon
Chapter 21 S Commands setup ficon S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m setup ficon To enter the automated FICON setup mode, use the setup ficon command in EXEC mode.
Page 970: Shared-Keymode
Chapter 21 S Commands shared-keymode S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m shared-keymode To configure the shared key mode, use the shared-keymode command.
Page 971: Shutdown
Chapter 21 S Commands shutdown S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m shutdown To disable an interface, use the shutdown command.
Page 972: Shutdown (Interface Configuration Submode)
Chapter 21 S Commands shutdown (interface configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m shutdown (interface configuration submode) To disable an Cisco SME interface, use the shutdown command.
Page 973: Shutdown (Cisco Sme Cluster Configuration Submode)
Chapter 21 S Commands shutdown (Cisco SME cluster configuration submode) S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m shutdown (Cisco SME cluster configuration submode) To disable a cluster for recovery, use the shutdown command.
Page 974: Site-Id
Chapter 21 S Commands site-id S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m site-id To configure the site ID with the Call Home function, use the site-id command in Call Home configuration submode.
Page 975: Sleep
Chapter 21 S Commands sleep S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m sleep To delay an action by a specified number of seconds, use the sleep command.
Page 976 Chapter 21 S Commands S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m To enable or disable the Cisco SME services, use the sme command.
Page 977: Snmp Port
Chapter 21 S Commands snmp port S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m snmp port Use the snmp port command to enable SNMP control of FICON configurations.
Page 978: Snmp-Server
Chapter 21 S Commands snmp-server S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m snmp-server To configure the SNMP server information, switch location, and switch name, use the snmp-server command in configuration mode.
Page 979 Chapter 21 S Commands snmp-server S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 980: Snmp-Server Contact
Chapter 21 S Commands snmp-server contact S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m snmp-server contact To modify system contact, use the snmp-server contact command in configuration mode.
Page 981: Snmp-Server Community
Chapter 21 S Commands snmp-server community S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m snmp-server community To set the SNMP server community string, use the snmp-server community command in configuration mode.
Page 982: Snmp-Server Enable Traps
Chapter 21 S Commands snmp-server enable traps S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m snmp-server enable traps To enable SNMP server notifications (informs and traps), use the snmp-server enable traps command.
Page 983 Chapter 21 S Commands snmp-server enable traps S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Defaults All the notifications listed in the Syntax Description table are disabled by default except for the following: entity fru, vrrp, license, link, and any notification not listed (including the generic...
Page 984 Chapter 21 S Commands snmp-server enable traps S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch(config)# snmp-server traps The following example enables all SNMP entity notifications.
Page 985: Snmp-Server Traps Entity Fru
Chapter 21 S Commands snmp-server traps entity fru S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m snmp-server traps entity fru To enable SNMP entity FRU trap, use the snmp-server traps entity fru command in configuration mode.
Page 986: Snmp-Server Enable Traps Fcdomain
Chapter 21 S Commands snmp-server enable traps fcdomain S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m snmp-server enable traps fcdomain To enable SNMP FC domain traps, use the snmp-server enable traps fcdomain command in configuration mode.
Page 987: Snmp-Server Enable Traps Link Cisco
Chapter 21 S Commands snmp-server enable traps link cisco S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m snmp-server enable traps link cisco To enable Cisco cieLinkUp and cieLinkDown traps, use the snmp-server enable traps link cisco command in configuration mode.
Page 988: Snmp-Server Enable Traps Zone
Chapter 21 S Commands snmp-server enable traps zone S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m snmp-server enable traps zone To enable SNMP zone traps, use the snmp-server enable traps zone command in configuration mode.
Page 989: Snmp-Server Globalenforcepriv
Chapter 21 S Commands snmp-server globalEnforcePriv S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m snmp-server globalEnforcePriv To globally enforce privacy for all SNMP users, use the snmp-server globalEnforcePriv command in configuration mode.
Page 990: Snmp-Server Host
Chapter 21 S Commands snmp-server host S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m snmp-server host To specify the recipient of an SNMP notification, use the snmp-server host global configuration command.
Page 991 Chapter 21 S Commands snmp-server host S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m switch(config)# snmp-server host 10.1.1.1 traps version 2c abcddsfsf udp-port 500 Related Commands Command...
Page 992: Snmp-Server Location
Chapter 21 S Commands snmp-server location S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m snmp-server location To modify system location, use snmp-server location command.
Page 993: Snmp-Server Tcp-Session
Chapter 21 S Commands snmp-server tcp-session S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m snmp-server tcp-session To enable one time authentication for SNMP over a TCP session, use the snmp-server tcp-session command in configuration mode.
Page 994: Snmp-Server User
Chapter 21 S Commands snmp-server user S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m snmp-server user To configure SNMP user information, use the snmp-server user command in configuration mode.
Page 995 Chapter 21 S Commands snmp-server user S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Usage Guidelines The localized keys are not portable across devices as they contain information on the engine ID of the device.
Page 996: Source
Chapter 21 S Commands source S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m source To configure a switched port analyzer (SPAN) source, use the source command in SPAN session configuration submode.
Page 997 Chapter 21 S Commands source S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m traffic-type (Optional) Configures the SPAN traffic type.
Page 998 Chapter 21 S Commands source S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m Related Commands Command Description...
Page 999: Span Max-Queued-Packets
Chapter 21 S Commands span max-queued-packets S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m span max-queued-packets To configure the SPAN max-queued-packets, use the span max-queued-packets command in configuration mode.To disable the SPAN drop-threshold, use the no form of the command.
Page 1000: Span Session
Chapter 21 S Commands span session S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m span session To configure a SPAN session, use the span session command.

This manual is also suitable for:

Ap775a - nexus converged network switch 5010 Ap776a - nexus converged network switch 5020 Cisco mds 9124 - fabric switch Cisco mds 9020 - fabric switch Cisco mds 9120 - fabric switch Cisco mds 9140 - fabric switch ... Show all

Cisco AJ732A - MDS 9134 Fabric Switch Command Reference Manual

Chapter 2 a Command

Chapter 3 B Command

Chapter 4 C Command

Chapter 5 D Command

Debug Commands

Chapter 6 Debug Command

Quick Links

Related Manuals for Cisco AJ732A - Cisco MDS 9134 Fabric Switch

Summary of Contents for Cisco AJ732A - Cisco MDS 9134 Fabric Switch