NEC MultiSync EA190M User Manual
Multisync ea190m-bk : user's manual
Hide thumbs
Also See for MultiSync EA190M:
- User manual (19 pages) ,
- Specifications (2 pages) ,
- Outline drawing (1 page)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for NEC MultiSync EA190M
Summary of Contents for NEC MultiSync EA190M
- Page 1 MultiSync EA190M User’s Manual...
-
Page 2: Table Of Contents
Index Warning, Caution ......................... English-1 Registration Information ....................... English-1 Recommended use ........................English-3 Contents ............................English-5 Quick Start ........................... English-6 Controls ............................English-10 Specifications ..........................English-13 Features ............................. English-14 Troubleshooting ......................... English-15 TCO Displays 5.0 ........................English-16 Manufacturer’s Recycling and Energy Information ..............English-17... -
Page 3: Registration Information
Japan Voltage 120* *When operating the MultiSync EA190M monitor with its AC 125-240V power supply, use a power supply cord that matches the power supply voltage of the AC power outlet being used. NOTE: This product can only be serviced in the country where it was purchased. -
Page 4: Canadian Department Of Communications Compliance Statement
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1. FCC Information Use the attached specified cables with the MultiSync EA190M (L197HL) color monitor so as not to interfere with radio and television reception. -
Page 5: Recommended Use
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. - Page 6 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen.
-
Page 7: Contents
Contents Your new NEC MultiSync LCD monitor box* should contain the following: • MultiSync LCD monitor with tilt/swivel/pivot/height adjust base • Power Cord • Base stand • Video Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male) •... -
Page 8: Quick Start
Quick Start To attach the Base to the LCD stand: 1. Place monitor face down on a non-abrasive surface (Figure 1). NOTE: Handle with care when monitor facing down, for avoiding damage to the front control buttons. 2. Please pivot base 90 degrees as shown in Figure 1. NOTE: Handle with care when pulling the stand. -
Page 9: Raise And Lower Monitor Screen
6. Connect the power cord to the power outlet (Figure C.1). NOTE: Please refer to Caution section of this manual for proper selection of AC power cord. 7. Turn on the monitor with the front power button and the computer (Figure C.1). 8. -
Page 10: Screen Rotation
Screen Rotation Before rotating, the screen must be raised to the highest level to avoid knocking the screen on the desk or pinching with your fingers. To raise the screen, with one hand, grip the top of the display by the handle using the other hand to grip the bottom. Lift up to the highest position (Figure RL.1). -
Page 11: Flexible Arm Installation
7. Reverse this process to re-attach stand. NOTE: Use only VESA-compatible alternative mounting method. Handle with care when removing stand. NOTE: Match “TOP SIDE” mark on stand to top side of the monitor head when re-attaching stand. “TOP SIDE” mark Please match top side of the monitor Flexible Arm Installation... -
Page 12: Controls
Controls OSD (On-Screen Display) control buttons on the front of the monitor function as follows: To access OSD menu, press any of the control buttons (MENU, Left, Right, Down, Up). To change signal input, press the SELECT button. To change ECO MODE, press the RESET/ECO MODE button. NOTE: OSD must be closed in order to change signal input. -
Page 13: Menu Tools
Image Controls (Analog input only) LEFT / RIGHT Controls Horizontal Image Position within the display area of the LCD. DOWN / UP Controls Vertical Image Position within the display area of the LCD. H.SIZE Adjusts the horizontal size by increasing or decreasing this setting. FINE Improves focus, clarity and image stability by increasing or decreasing this setting. - Page 14 OSD Warning OSD Warning menus disappear with Exit button. NO SIGNAL: This function gives a warning when there is no Horizontal or Vertical Sync. After power is turned on or when there is a change of input signal, the No Signal window will appear. OUT OF RANGE: When input signal is non-supported timing or the video signal doesn’t have proper timing, the Out of Range menu will appear.
-
Page 15: Specifications
1152 x 870* @ 75 Hz 1280 x 960* @ 60 Hz to 75 Hz NEC DISPLAY SOLUTIONS cites recommended 1280 x 1024* @ 60 Hz to 75 Hz..resolution for optimal display performance. Active Landscape: Horiz.: 376.3 mm/14.8 inches Display Area Vert.: 301.1 mm/11.9 inches... -
Page 16: Features
Carbon conversion factor - conversion factor is based on OECD publication of global CO2 emissions 2008 Edition). This monitor has a manufacturing carbon footprint of approximately 20.8 kg. Note: The manufacturing and operating carbon footprints are calculated by a unique algorithm developed exclusively by NEC for its monitors. -
Page 17: Troubleshooting
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. -
Page 18: Tco Displays 5.0
TCO Displays 5.0 Congratulations! This display is designed for both you and the planet! The display you have just purchased carries the TCO Certified label. This ensures that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. -
Page 19: Manufacturer's Recycling And Energy Information
Manufacturer’s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally- friendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).