hit counter script
Cisco WIC-1ENET - 1700 Access Routers 1port10bt Enet Wan Interface(man Configuration Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Router
  5. WIC-1ENET - 1700 Access Routers 1port10bt Enet Wan...
  6. Configuration manual

Cisco WIC-1ENET - 1700 Access Routers 1port10bt Enet Wan Interface(man Configuration Manual

Configuring a single-port ethernet wic on a router
Hide thumbs Also See for WIC-1ENET - 1700 Access Routers 1port10bt Enet Wan Interface(man:
Table of Contents

Advertisement

Quick Links

Download this manual
Configuring a Single-Port Ethernet WIC on a
Cisco 1700 Series Router
The Cisco WIC-1ENET is a single-port Ethernet interface card supporting 10BASE-T Ethernet. The
card provides the Cisco 1700 series router with additional Ethernet interfaces.
Figure 1
shows the Cisco WIC-1ENET interface card.
Figure 1
Cisco WIC-1ENET Interface Card
S E E M A N
U A L
B E F O R E
IN S T A L L
A T IO N
The LNK (physical layer link) LED is on when the IOS recognizes the Cisco WIC-1ENET card and the
connection is up. The FDX LED is on when the port is operating in full-duplex mode, and off when
operating in half-duplex mode. Additionally, the Activity LED on the front of the Cisco 1700 series
router indicates that data is transmitted or received on the slot.
Note
The Cisco 1700 Router Hardware Installation Guide provides procedures for physical installation.
Although those instructions are for a WAN interface card (WIC), the procedures also apply to installing
this card.
This document contains the following sections:
Cisco WIC-1ENET Requirements
•
IOS Commands
•
Caveats
•
Related Documents
•
Safety Warnings
•
Corporate Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
© 2005 Cisco Systems, Inc. All rights reserved.
L N K
F D X
W IC
1 E N E T
1 0 B T E T
H E R N E T

Advertisement

Table of Contents
loading

Related Manuals for Cisco WIC-1ENET - 1700 Access Routers 1port10bt Enet Wan Interface(man

Summary of Contents for Cisco WIC-1ENET - 1700 Access Routers 1port10bt Enet Wan Interface(man

  • Page 1 H E R N E T The LNK (physical layer link) LED is on when the IOS recognizes the Cisco WIC-1ENET card and the connection is up. The FDX LED is on when the port is operating in full-duplex mode, and off when operating in half-duplex mode.

  • Page 2: Processor Requirements

    WIC slot other than slot 0 or if more than one card is installed. The card can be used with Cisco IOS Release 12.2(4)T, but the card must be installed in slot 0 and only one Cisco WIC-1ENET card can be installed in the router.
  • Page 3 This section describes the full-duplex and half-duplex IOS commands. Cisco WIC-1ENET is set to half-duplex mode by default, and it does not auto-sense. If you set the Cisco WIC-1ENET to full-duplex operation, you must also set the device to which the port is attached to full-duplex mode.
  • Page 4 Command Mode Interface configuration mode Usage Guidelines Use the half-duplex command to put the Cisco WIC-1ENET Ethernet interface into 10 Mbps half-duplex operation, the default state of the Ethernet interface. Example The following example puts the Ethernet interface into half-duplex mode of operation.
  • Page 5 This section provides the latest information about using a Cisco WIC-1ENET card when the router is running Cisco IOS Release 12.2(2)XJ or higher. If the Cisco WIC-1ENET is used with an IOS image that does not support it and if the Link LED •...

  • Page 6: Related Documents

    Cisco 1700 series router. • Release Notes for the Cisco 1700 Series Routers for Cisco IOS Release 12.2(4)T and Release Notes for the Cisco 1700 Series Routers for Cisco IOS Release 12.2(7)XJ—provide information for running IOS images on a Cisco 1700 series router.

  • Page 7: Tärkeitä Turvallisuusohjeita

    Safety Warnings Varoitus TÄRKEITÄ TURVALLISUUSOHJEITA Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.

  • Page 8: Instruções Importantes De Segurança

    Safety Warnings Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes.

  • Page 9: Vigtige Sikkerhedsanvisninger

    Safety Warnings Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.
  • Page 10 Safety Warnings Warning Definition 78-11422-03...

  • Page 11: Power Supply Warnings

    Safety Warnings Power Supply Warnings The following warnings apply when you are installing a card or working with the power supply: Warning Read the installation instructions before you connect the system to its power source. Statement 1004 Only trained and qualified personnel should be allowed to install or replace this equipment. Statement Warning 1030 Warning: Before working on a system that has an on/off switch, turn OFF the power and unplug the...

  • Page 12: Electrical Warnings

    Safety Warnings Electrical Warnings The following warnings apply when you are working with electricity: Warning To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors.

  • Page 13: Configuring The Interface

    Configuring the Interface Whenever you install a new Cisco WIC-1ENET card, or if you want to configure an existing card, you must configure the interface. If you replace a card that was already configured, the router recognizes it and brings up the interface by using the existing configuration.
  • Page 14 Router(config-if)# The prompt changes again to show that you are in interface configuration mode. Configure the routing protocols on the Cisco WIC-1ENET interface. (You must have previously enabled Step 6 these protocols as part of global configuration.) In this example, IP and IPX are being configured:...

  • Page 15: System Configuration Dialog

    Follow these steps to configure the router by using the system configuration dialog: Step 1 Power down the router, and install the Cisco WIC-1ENET. Step 2 Connect a console to the router. If you need instructions for connecting a console, refer to the installation chapter of your router installation and configuration guide.
  • Page 16 Connecting a Cisco WIC-1ENET Card to the LAN Respond to the prompt as follows: Would you like to enter basic management setup? [yes/no]: no First, would you like to see the current interface summary? [yes]: no Enter the host name of the router as follows:...
  • Page 17 Router Configuration Scenarios The following examples shows a Cisco 1700 series router configured to use the Cisco WIC-1ENET. These are sample configurations. For descriptions of the features and commands, see the configuration guidelines on the Cisco website.
  • Page 18 Connecting a Cisco WIC-1ENET Card to the LAN vpdn enable no vpdn logging vpdn-group 1 request-dialin protocol pppoe ip host pppoe_server 16.0.0.2 crypto isakmp enable crypto isakmp key 12abcjhrweit345 address 16.0.0.2 crypto isakmp identity address crypto isakmp policy 1 auth pre-share...

  • Page 19: Obtaining Documentation

    1 permit 12.0.0.0 0.0.0.255 Obtaining Documentation Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems.

  • Page 20: Documentation Feedback

    Register to receive security information from Cisco. • A current list of security advisories and notices for Cisco products is available at this URL: http://www.cisco.com/go/psirt If you prefer to see advisories and notices as they are updated in real time, you can access a Product Security Incident Response Team Really Simple Syndication (PSIRT RSS) feed from this URL: http://www.cisco.com/en/US/products/products_psirt_rss_feed.html...

  • Page 21: Obtaining Technical Assistance

    Cisco TAC engineer. The TAC Service Request Tool is located at this URL: http://www.cisco.com/techsupport/servicerequest For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco TAC engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.

  • Page 22: Definitions Of Service Request Severity

    Definitions of Service Request Severity To ensure that all service requests are reported in a standard format, Cisco has established severity definitions. Severity 1 (S1)—Your network is “down,” or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.
  • Page 23 Cisco 1700 Router Hardware Installation Guide, and the Cisco IOS configuration guides and command references. CCSP, CCVP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.;...
  • Page 24 Obtaining Additional Publications and Information Obtaining Additional Publications and Information 78-11422-03...

This manual is also suitable for:

1700 series

Table of Contents