Page 1
PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 PIONEER CORPORATION 2014 K-FZV OCT.
Page 2
Wave length (typ) : 790 nm Operation output : 3 mW CW, Class 1 Maximum output : Class 1 (Under fault condition) LABEL CHECK The following caution appears on your unit. Location: inside of the unit (Printed on the Chassis Back) X-HM82-K...
Page 3
11.3 CD ASSY ..................................98 11.4 FRONT ASSY and KEY ASSY ..........................100 11.5 SMPS ASSY and CNT1 ASSY ..........................102 11.6 CNT2 ASSY................................106 11.7 USB GUIDE ASSY, GUIDE1 ASSY and GUIDE2 ASSY ..................107 12. PCB PARTS LIST................................108 X-HM82-K...
Page 4
Remove the solder on the short circuit position after connecting the Pickup PCB and CD ASSY with Cable Flat Card 16P. Fig. 1 • Bottom side Pickup PCB CD Mecha Cable Flat Card 16P Soldering short land Short circuit using a soldering iron. Cable Flat Card 16P CD ASSY X-HM82-K...
Page 5
Loading Rack in the direction of blue arrow, as indicated in the photo. If the Tray pops out a little, fully pull it out by hand. Loading Rack Screwdriver Slit CD Mecha Tray Tray open X-HM82-K...
Page 8
NEC Corporation. FontAvenue is a registered trademark of NEC Corporation. • iOS is a trademark on which Cisco holds the trademark right in the US and certain other countries. • Android and Google Play are trademarks of Google Inc. X-HM82-K...
Page 9
(2) Cleaning Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools. Position to be cleaned Name Part No. Remarks Pickup lens Cleaning liquid GEM1004 Refer to “7. DISASSEMBLY”. Cleaning paper GED-008 X-HM82-K...
Page 10
3.3 PCB LOCATIONS GUIDE2 ASSY KEY ASSY USB GUIDE ASSY FRONT ASSY USB ASSY CD Mecha GUIDE1 ASSY CD ASSY MAIN ASSY SMPS ASSY CNT2 ASSY CNT1 ASSY DMAIN ASSY X-HM82-K...
Page 11
The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. LIST OF ASSEMBLIES Mark Symbol & Discription X-HM82-K/ X-HM82-S/ XC-HM82-K/ XC-HM82-S/ XC-HM82-K/...
Page 13
When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST". The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. X-HM82-K...
Page 16
CNT2 ASSY ==>CP312 1PIN : LOW 3.AMP PROTECTION Check the protection circuit CNT2 ASSY ==>CP312 22PIN : HIGH (Refer to the “ 5.2 PROTECTION CIRCUIT) 4.POWER PROTECTION CNT1 ASSY ==>CP307 12PIN : LOW 5.OVER TEMPERATURE PROTECTION CNT2 ASSY ==>CP312 13,14PIN : LOW X-HM82-K...
Page 17
Replace the IC506 Check the Pins 27, Check the speaker 29 output of CP526 relay and its peripheral (DMAIN ASSY) circuits Check the pattern Q322, Q323, Q328, Q329 is defective Go to STEP2 Replacement is difficult, so replace the MAIN ASSY X-HM82-K...
Page 18
Check the Pins 5, 7 signal of CN101 Check the short of JK101 (FRONT ASSY) Check the pattern Check the short of JK100 Check the pattern Check the Pins 27, 29 signal of CP320 Check the connector of CNT1 ASSY Go to STEP2 X-HM82-K...
Page 20
Detect abnormal PWM waveforms in the speaker outputs (AMP_OUT_L, AMP_OUT_R) that result from abnormality in the AMP Block, and apply protection. Operable with IC609_2Pin "H" -> "L". AMP_OUT_R Q330 D323 KTC3875S 1SS355 PIN NO.2 IC609 D324 AMP_OUT_L 1SS355 M3030RFGPFP CNT2 ASSY MAIN ASSY DMAIN ASSY X-HM82-K...
Page 21
DC_PROTECT IC609 M3030RFGPFP Q334 KTC3198Y CNT2 ASSY MAIN ASSY 140720 SHORT PROTECTION D_3V3_SW D384 140724 PIONEER Q702 KTC3875G Q701 R333 KTC3875G DMAIN ASSY DGND 140724 PIONEER • AMP PROTECTION Detect abnormality in the AMP Block (mainly IC310 and IC311 as well as their power supplies and peripheral circuits), and apply protection.
Page 22
Detect abnormal heating of the AMP R channel circuits (mainly: IC311, Q328 and Q329) by means of the PTC thermistor (P301), and apply protection. Operable with IC609_93Pin "H" -> "L". PIN NO.93 POSISTOR IC609 M3030RFGPFP AGND CNT2 ASSY MAIN ASSY DMAIN ASSY X-HM82-K...
Page 23
- "Network Standby"and "Bluetooth Standby" are On. Network Standby+Bluetooth Standby - LCD is turned Off. - HM72/82 is turned On. In case that BT Audio Power On is selected, On. - LCD is turned On. In other case, Off. X-HM82-K...
Page 24
4 Double-click on Internet Protocol. IP address: 192.168.0.1 Subnet mask:255.255.255.0 Gateway address: 0.0.0.0 DNS (1st): 0.0.0.0 DNS (2nd): 0.0.0.0 Proxy setting: Not to be used 5 After setting is finished, reboot the unit. MAC Address seal 5 Set the items as shown below. X-HM82-K...
Page 25
If the SSID for the prepared router is displayed on the list, the Wi-Fi antenna works properly. Note: As the SSID name for a wireless LAN router supports only one-byte alphanumerics, if two-byte characters are used in an SSID name, rename it. X-HM82-K...
Page 26
2. Select the iPod function then connect an Apple Device (iPod, etc.) to the USB terminal. If charging of the Apple device starts, it is OK. If Apple device does not recognized, refer to the diagnosis flowchart for a case in which the No sound from USB function on "5.1 TROUBLESHOOTING". X-HM82-K...
Page 27
TX0_DI_NW Data output of network module communication (Sub->DM860) P11/EX25/SI00/RxD0 RX0_DO_NW Data input of network module communication (DM860->Sub) P10/EX24/SCK00 CLK_NW Clock output of network module communication AVREF1 AVREF1 P110/ANO0 P111/ANO1 CS_NW Chip select output of network module communication AVREF0 AVREF0 X-HM82-K...
Page 28
Ground (except P121-P124 and port block) EVSS0 EVSS0 Ground of port block (except P20-P27, P110, P111, P121-P124, P150-P157) Positive power supply (except P121-P124 and port block) EVDD0 EVDD0 Positive power supply of port block (except P20-P27, P110, P111, P121-P124, P150-P157) X-HM82-K...
Page 29
O t h e r 2 . : 4 . 3 . 1 7 . E X 4 6 5 0 6 - 1 In the case of a DAB model, the version of a DAB module is displayed. X-HM82-K...
Page 30
Check mode, the selected function screen will be displayed until network connection is established (it may take up to dozens of seconds), then the Protect Check Mode screen will be displayed. Example: Startup → Pioneer Logo → Music Server screen → Network established → Protection Check screen Canceling Operation Lock ...
Page 31
"g (STOP)" and "STANDBY/ON" buttons Unit "STANDBY/ON" during Cold Standby. The last protection activation that was detected before Protect Check mode is entered will be displayed. Unit "np" Unit "np" Unit "np" Unit "np" Unit "np" X-HM82-K...
Page 32
Unit "STANDBY/ON" To turn the unit off, press the "STANDBY/ON" button during Protect Check mode. Remarks During Protect Check mode, response to keys other than those described below is disabled. Unit "" button Unit " (Play/Pause)" button Unit "STANDBY/ON" button X-HM82-K...
Page 33
Each time the 1 key on the remote control unit with the product is pressed, the screen is changed as shown below: Ramp > Black > White > Red > Green > Blue If the 0 key is pressed, the screen will return to that of Test Mode. [Screens to be displayed] X-HM82-K...
Page 34
This unit can display all the characters that are indicated in the white cells in the table below properly but cannot display the characters in gray cells properly and will indicate such characters as "#." Those are the characters shown below in the RDS standard: 0x5E 0x60 0x7E X-HM82-K...
Page 35
Power Cord in the power supply. R626 (5) After the electric charge of the product is discharged in Step (4), remove the tweezer that have short-circuited R626 and GND and tweezer then turn ON the power supply. C602 Front X-HM82-K...
Page 36
(1) Disconnect the two connectors. Note: ∗1 ∗1: A lock mechanism exists in the connector FPC300 (FPC300). You should remove it with care. (2) Remove the four screws. CN101 X-HM82-K/SYXEV8: B020030083F10-IL CNT1 ASSY X-HM82D-K/VXEV8: Front XC-HM82-K/SYXEV8: XC-HM82-K/CXEV: XC-HM82D-K/VXEV8: X-HM72-K/SYXEV8: X-HM72D-K/VXEV8:...
Page 37
Note on assembling Binder Chassis Back ∗3: Don't touch the cables to the Cabinet Top. ∗4: When replacing the Chassis Back or the Cable ASSY (250mm) Cable ASSY (250mm), don’t forget to attach Tube the Tube and bind it. Front X-HM82-K...
Page 38
CD ASSY. Front Note on assembling CD ASSY ∗6: When replacing the CD ASSY, attach the Cushion DAB. ∗7: Don't touch the cables to the Cabinet Top. PN1705 CD ASSY ∗7 ∗7 Cable ASSY (200mm) DMAIN ASSY Front X-HM82-K...
Page 39
CD ASSY and the two cables. CD Mecha Note: If you carry out diagnosis, it is not necessary to disconnect. (8) Remove the Cover Tray. Cover Tray Note: If you carry out diagnosis, it is not necessary to remove. X-HM82-K...
Page 40
CNT2 ASSY. (Refer to the “[3] DMAIN ASSY, CNT1 ASSY and CNT2 ASSY”. ) ----------------------------------------------------------------- (1) Allocate the CD Mecha with the CD ASSY Front connected by 16P FFC extension jig cable (GGD1774). Not necessary to fix it with screws. X-HM82-K...
Page 41
(rotation) in the next step. DMAIN ASSY PN1705 ∗9 CN101 FPC300 CNT2 ASSY CD ASSY 7P cable PN1702 Cable Flat Card 45P Note: ∗9: A lock mechanism exists in the connector (FPC300). You should connect it with care. X-HM82-K...
Page 42
[5] SMPS ASSY Remove the Cabinet Top. (Refer to the “[1-1] Cabinet Top”. ) ----------------------------------------------------------------- (1) Remove the screw of bottom side. (BBZ30P080FTC) SMPS ASSY (2) Remove the screw of rear side. (BBT30P100FTB) (3) Remove the screw. (BBZ30P080FTC) Bracket SMPS Front X-HM82-K...
Page 43
GUIDE1 ASSY. CP315 CP314 (3) Remove the screw. (B020230063B10-IL) (4) Remove the four screws. (BBZ30P080FTC) (5) Remove the MAIN ASSY. (6) X-HM82D-K/VXEV8, XC-HM82D-K/VXEV8, X-HM72D-K/VXEV8, X-HM72D-S/YXEV8 only: Remove the DAB and Cushion DAB. Cushion DAB MAIN ASSY CP300 MAIN ASSY X-HM82-K...
Page 44
FFC's. Lock it surely not to insert it at a tilt. LCD Display ∗12 FORNT ASSY MOD100 FORNT ASSY FPC102 FPC102 FFC (LCD Display) MOD100 Cable Flat Card 45P Cable Flat Card 45P X-HM82-K...
Page 45
Pickup portion to outermost periphery, and then carry out the cleaning. Tray window Clean the Pickup Lens when it is stained, Pickup portion using following cleaning materials: Cleaning liquid : GEM1004 gear Cleaning paper : GED-008 Pickup Lens X-HM82-K...
Page 46
When replacing the Cable ASSY (250mm), don’t forget to attach the Tube and bind it. Front Tube Cable ASSY (250mm) Cable Flat Card 45P Front GND cable CN. Wire 2mm USB CN. Wire 2mm Mecha 5P CN. Wire 2mm Mecha 6P Front X-HM82-K...
Page 47
2. Plug the Power cord. (STANDBY mode) For updating of the MAIN microcomputer, proceed with Please push the cancel button and press the JIG's the following steps in STANDBY mode. RESET button. And confirm a connection of FFC. Please return to procedure 1. X-HM82-K...
Page 48
1 Set speed of update. 1 Set speed of update. Set Baud rate to 38400. (Default Baud rate is 9600) Press the OK button. 2 Update the MAIN microcomputer. E.P.R=>Erase+Program+Read 2 Update the MAIN microcomputer. Press the E.P.R … button Press OK button. X-HM82-K...
Page 49
Key operation After restart of CX870 is completed, disabled the background will be displayed. After restart is completed, the updating process will automatically start. The progress of updating will be displayed with the progress bar. In units of 20% X-HM82-K...
Page 50
3. Set the Function selection to CD. 4. Open the disc tray, load the created disc, then close the tray. 5. Updating starts automatically. 6. After updating is completed, the disc tray will be automatically opened. 7. Unload the disc then turn the unit OFF. X-HM82-K...
Page 52
TUNER EDIT SHUFFLE SHUFFLE REPEAT +100 +100 +100 +100 PLAY MODE PLAY MODE PLAY MODE SHUFFLE OPTION ENTER ENTER FOLDER - CLEAR CLEAR CLEAR FOLDER + FOLDER - SORT FOLDER - CLEAR FOLDER + +Favorites FOLDER + PLAY MODE X-HM82-K...
Page 53
This transmits the code of "NETWORK" key in HM71/81. OPTION + NET RADIO This transmits the code of "NETWORK" key in HM71/81. OPTION + FAVORITES This transmits the code of "NETWORK" key in HM71/81. OPTION + FOLDER+ This transmits the code of "+Favorite" key in HM71/81. X-HM82-K...
Page 54
Screws adjacent to b mark on product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 9.1 PACKING SECTION X-HM82-K/SYXEV8, X-HM82-S/SYXEV8, X-HM82-S/AXEV5, XC-HM82-K/SYXEV8,...
Page 55
22 Stard ASSY 4148210221000V 23 Speaker See Contrast table (2) (2) CONTRAST TABLE X-HM82-K/SYXEV8, X-HM82-S/SYXEV8, X-HM82-S/AXEV5, X-HM82D-K/VXEV8, XC-HM82-K/SYXEV8, XC-HM82-S/ SYXEV8, XC-HM82-K/CXEV, XC-HM82D-K/VXEV8, X-HM72-K/SYXEV8, X-HM72-S/SYXEV8, X-HM72D-K/VXEV8 and X-HM72D-S/YXEV8 are constructed the same except for the following: Mark No. Symbol and Discription...
Page 56
9.2 EXTERIOR SECTION Accessory of Panel Inner Double side tape Double side tape X-HM82-K...
Page 57
X-HM82D-K/VXEV8, X-HM82D-K/VXEV8, Acetate tape X-HM72D-K/VXEV8, X-HM72D-S/YXEV8 only A ´ A ´ X-HM82-K...
Page 58
30 Cover BT 4310216061100S 66 Tube A700101019010S 31 Cover Tray See Contrast table (2) 32 Foot See Contrast table (2) 33 Panel Front See Contrast table (2) 34 Shield USB Plate 3070210697000S 35 Cabinet Top See Contrast table (2) X-HM82-K...
Page 59
(2) CONTRAST TABLE X-HM82-K/SYXEV8, X-HM82-S/SYXEV8, X-HM82-S/AXEV5, X-HM82D-K/VXEV8, XC-HM82-K/SYXEV8, XC-HM82-S/ SYXEV8, XC-HM82-K/CXEV, XC-HM82D-K/VXEV8, X-HM72-K/SYXEV8, X-HM72-S/SYXEV8, X-HM72D-K/VXEV8 and X-HM72D-S/YXEV8 are constructed the same except for the following: Mark No. Symbol & Discription X-HM82-K/ X-HM82-S/ X-HM82-S/ X-HM82D-K/ XC-HM82-K/ XC-HM82-S/ SYXEV8 SYXEV8 AXEV5 VXEV8...
Page 60
9.3 SPEAKER SECTION (S-HM82GB, S-HM82SA) Styling of cables Front Band Tape 60 x 280mm X-HM82-K...
Page 61
S-HM82GB and S-HM82SA are constructed the same except for the following: Mark No. Symbol & Discription S-HM82GB S-HM82SA NSP 6 Duct 1830210290000S 1830210300000S NSP 10 Cabinet 1280210097000S 1280210107000S NSP 11 Model Label 5507000018480S 5507000018450S 26 Sheet 1210212909000S 1210212929000S 27 Sheet 1210212919000S Not used X-HM82-K...
Page 62
9.4 SPEAKER SECTION (S-HM72) Tape Polyethylene Bag style Front (side) Tape (clear) 10 x 100mm Band X-HM82-K...
Page 63
6 Network ASSY 8952SHM720004 17 Snow Cushion 8952SHM720005 7 Terminal Network ASSY 8952SHM700027-IL 18 Polyethylene Bag 8952SHM700044-IL 8 Cap Terminal BK 8952SHM700028-IL 19 Wire SPK ASSY 8952SHM700042-IL 9 Cap Terminal RED 8952SHM700029-IL 10 Foot Cushion • • • • • X-HM82-K...
Page 64
When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST". The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. X-HM82-K...
Page 65
(DAC) CP313 CP301 (LINE) : Audio Signal Route (LINE IN Lch) (TU) : Audio Signal Route (TUNER Lch) (SW) : Audio Signal Route (SubWoofer ch) (DAC) : Audio Signal Route (DAC Lch) (CD) : Audio Signal Route (CD Lch) X-HM82-K...
Page 75
EU-TUNER CHN-TUNER KTC3875G R698 R672 OPEN PIN.91 KTC3875G R693 Q611 R700 R671 OPEN R695 100K Power_Down change OPEN R838 OPEN R839 OPEN R840 UART_OPTION OPEN R620 R732 OPEN R603 OPEN (DAC) (DAC) (DAC) : Audio Signal Route (DAC Lch) X-HM82-K...
Page 81
R124 D109 CDS3C05HDMI D110 CDS3C05HDMI C139 C140 100N C141 100N D111 CN102 CDS3C05HDMI GND102 GND101 (FL) radiation step NOISE : Audio Signal Route (FRONT IN Lch) (HP) : Audio Signal Route (HEADPHONE Lch) (UD) : USB Data Signal Route X-HM82-K...
Page 82
GND TERMINAL XHM72/82 ONLY INDICATIES SAFETY CRITICAL COMPONENTS. TO REDUCE THE RISK OF ELECTIC SHOCK. LEAKAGE CURRENT OF RESISTANCE MEASUREMENTS SHALL BE CARRIED OUT(EXPOSED PARTS ARE ACCEPTABLY INSULATED FROM THE SUPPLY CIRCUIT) BEFORE THE APPLIANCE RETURNED TO THE CUSTOMER. X-HM82-K...
Page 88
IC313 OUT PUT(-12V) IC313 IN PUT (-18V) GND(-30V) IC315 //LM7905 IC 309 //LM7812 POWER_ON IC315 IN PUT (-12V) IC315 OUT PUT(-5V) OUT (18V) =>30-18=12V POWER_OFF IC314 //LM7805 IC 309 //LM7812 POWER_OFF POWER_ON IC314 IN PUT (+12V) IC314 OUT PUT(+5V) IN (7.2V)=>30-7.2=22.8V X-HM82-K...
Page 92
11. PCB CONNECTION DIAGRAM 11.1 MAIN ASSY SIDE A MAIN ASSY Q320 Q322 Q323 Q328 Q329 Q313 Q308 Q319 IC300 IC308 IC310 IC311 IC303 IC302 IC305 IC307 IC304 X-HM82-K...
Page 93
1. The parts mounted on this PCB include all necessary parts for several destinations. For further information for respective destinations, be sure to check with the schematic diagram. 2. View point of PCB diagrams. Connector Capacitor SIDE A SIDE B P.C.Board Chip Part X-HM82-K...
Page 94
SIDE B MAIN ASSY CP320 Q326 Q327 Q335 Q330 Q315 Q341 Q325 Q324 IC315 IC314 X-HM82-K...
Page 98
11.3 CD ASSY SIDE A CD M CD ASSY 7020-07686-000-0S X-HM72/82(MP) PN1603 PN1604 Q1601 IC1604 IC1603 IC1606 CD MECHA SIDE B CD ASSY PN1603 PN1604 X-HM82-K...
Page 99
SIDE A CD MECHA (Pick up) PN1602 CLAMP1001 Q1604 Q1603 Q1602 Q1605 IC303 IC1601 IC1605 IC1602 IC1607 SIDE B PN1602 X-HM82-K...
Page 100
11.4 FRONT ASSY and KEY ASSY SIDE A FRONT ASSY Q107 Q101 FPC102 FPC300 SIDE B FRONT ASSY FPC102 Q103 Q100 Q102 X-HM82-K...
Page 101
SIDE A KEY ASSY SIDE B KEY ASSY X-HM82-K...
Page 102
11.5 SMPS ASSY and CNT1 ASSY SIDE A SMPS ASSY CP319 CN221 IC821 CNT1 ASSY CP529 CP15 CP12 CP307 CP303 CP305 BKT BURRING TY 7020-07687-000-0 XHM72/82 CNT1 B`D (MP) BKT BURRING TYPE CP321 CP320 X-HM82-K...
Page 103
SIDE A MAIN AC IN TRANS CN803 CN801 IC821 PN1705 FPC102 CP309 FPC300 BKT BURRING TYPE CN101 CN101 687-000-0S BKT BURRING TYPE X-HM82-K...
Page 104
SIDE B SMPS ASSY CN801 CN803 Q221 CNT1 ASSY FPC300 CP309 CN101 X-HM82-K...
Page 105
SIDE B CN221 Q221 Q271 IC251 CP305 CP303 CP307 CP321 X-HM82-K...
Page 106
11.6 CNT2 ASSY SIDE A SIDE A CP301 CNT2 ASSY CP313 XHM72/82 CNT2 B`D (MP) BKT BURRING TYPE BKT BURRING TYPE CP312 CP311 CP526 PN1702 SIDE B SIDE B CNT2 ASSY CP312 CP311 CP313 X-HM82-K...
Page 107
11.7 USB GUIDE ASSY, GUIDE1 ASSY and GUIDE2 ASSY SIDE A SIDE A USB GUIDE ASSY GUIDE1 ASSY GUIDE2 ASSY SIDE B SIDE B USB GUIDE ASSY GUIDE1 ASSY GUIDE2 ASSY X-HM82-K...
Page 108
→ 5621 ..............RN1/4PC 562 × 10 5 6 2 1 Meaning of the figures and others in the parentheses in the parts list LIST OF ASSEMBLIES Mark Symbol & Discription X-HM82-K/ X-HM82-S/ XC-HM82-K/ XC-HM82-S/ XC-HM82-K/ X-HM82-S/ SYXEV8 SYXEV8 SYXEV8...
Page 109
IC 312 LINEAR-REGULATOR J126780500450-IL IC 504,505 LINEAR OP J121458000050-IL IC 506 LOGIC-D/A CONVER J042448000010S SMPS ASSY IC 601 MEMORY-EEPROM J000241600170-IL SMPS ASSY has no service parts. IC 607 LOGIC-DECODER J044337395930-IL IC 609 CPU MICRO PROCESS 8952HM7200030 IC 2207 LOGIC-INTERFACE J046921100010-IL X-HM82-K...
Page 110
CNT1 ASSY has no service parts. CNT2 ASSY CNT2 ASSY has no service parts. USB GUIDE ASSY USB GUIDE ASSY has no service parts. GUIDE1 ASSY GUIDE1 ASSY has no service parts. GUIDE2 ASSY GUIDE2 ASSY has no service parts. X-HM82-K...