Related Manuals for Electrolux AEG VS91404-M
Summary of Contents for Electrolux AEG VS91404-M
- Page 1 ELECTROLUX HOME PRODUCTS PTY LTD ABN 51 004 762 341 Issue: 1 Technical Publication Nº CE1012 Date: 2/17 Vacuum Drawer Service Instruction MODEL: VS91404-M PNC 947727278 Copyright 2017 ELECTROLUX HOME PRODUCTS PTY LTD Technical Services...
- Page 2 CONTENTS Installation page 2 Accessible parts page 3 Replacement of components on the outside of the equipment page 4 Replacement of components on the inside of the equipment page 7 Problems and solutions page 14...
- Page 3 Installation CAUTION! The appliance must be installed by qualified personnel only. Remove the packaging material. Do not install or use the appliance if damaged. Comply with the instructions supplied with the appliance. Always pay attention when moving the appliance. Always wear safety gloves. ...
- Page 4 Accessible parts This chapter explains how to access and remove the various parts of the machine. Depending on the part to be removed, other parts may have to be removed first. To reassemble a part, follow the instructions in the reverse order. The operations described below must be carried out by staff who are trained and qualified for this type of intervention.
- Page 5 Replacement of components on the outside of the equipment To replace or perform maintenance on these components just open the drawer and perform the required work. Here is the work you can perform with the above procedure: Replacement of the sealing bar ...
- Page 6 Replacement of the silicone counterbar Remove the adhesive counterbar (A) from the cover Fig. 1.4 and remove any adhesive residue from the cover, using soap and water only (Fig.1.4). Remove the protection film from the new counterbar (Fig.1.5). Place the new counterbar on the sealing bar, with the adhesive side facing upwards (Fig.1.6).
- Page 7 Turn on the equipment and set the vacuum to an Fig. 1.7 average value Close the cover so that the new counterbar sticks on in the correct position (Fig.1.7). Make the counterbar stick firmly to the counterbar cover (Fig.1.8). Fig. 1.8 Rearming the circuit breaker The machine is equipped with a safety circuit Fig.
- Page 8 Replacement of components on the inside of the equipment To replace or perform maintenance on these components is necessary to remove the equipment from the recessed area of the unit. Place it on a worktop and carry out the procedure described below: Remove the screws by holding the top casing of the Fig.
- Page 9 Remove the 4 screws (2 on each side) that secure Fig. 1.12 the tank to the drawer (Fig.1.12). Lift the tank and insert a shim (e.g. a wooden board) between the tank and the drawer to work on the internal components (Fig.1.13). Fig.
- Page 10 Replacement of the sealing membrane Remove the sealing bar (Fig.1.14). Fig. 1.14 Disconnect the electrical connection and the pipe from the fitting of the membrane to be replaced (Fig.1.15). Unscrew the membrane clamping bush (Fig.1.16). Remove the membrane and replace it (Fig.1.17). Fig.
- Page 11 Replacement of the extensors DISASSEMBLE THE EXTENSORS WHEN THE Fig. 1.18 COVER IS OPEN! Unscrew the upper and lower fixing nut of the right extensor and disassemble it (Fig.1.18). Unscrew the upper and lower fixing nut of the left extensor and disassemble it (Fig.1.19). CAUTION: Pay attention to the cover, which might fall when disassembling the extensors! Now mount the new extensors.
- Page 12 Replacement of the cover DISASSEMBLE THE COVER BY KEEPING IT Fig. 1.20 OPEN! Unscrew the top nut that secures the extensor to the cover lever and release it (Fig.1.20). Repeat the operation on the other extensor as well. CAUTION: Pay attention to the cover, which might fall when disassembling the extensors! Close the cover and undo the 2 screws that secure the lever to the cover (this operation must be carried...
- Page 13 Replacement of the “main board” (power board) Disconnect the flat that connects the main Fig. 1.22 board to the user interface board Disconnect the vacuum sensor pipe Disconnect the various electrical connections. Now use a tool (e.g. a screwdriver) to release the 4 pins blocking the board and replace it (Fig.
- Page 14 Replacement of the transformer Disconnect the wires of the transformer’s electric Fig. 1.24 connection, loosen the fixing screw and replace it (Fig.1.24). Replacement of the circuit breaker Disconnect the wires of the electrical connection for Fig. 1.25 the circuit breaker. Unscrew the nut that secures the circuit breaker and replace it (Fig.1.25).
- Page 15 Problems and solutions...
- Page 16 What to do if… Problem Possible cause Solution The sealing time is not correct. Change the sealing time. The cover gasket is dirty or Clean or replace the cover gasket worn. The pouch is not placed The pouch is not Position the pouch correctly.