Advertisement
Quick Links
FLOOR STANDING SUPPORT PLATE FOR LOSSNAY
MODEL
PZ-1VS-E
LGH-15 to 50RVX3-E
PZ-2VS-E
LGH-65 to 100RVX3-E
Installation Manual
■ This manual must be read both fully and carefully before commencing installation procedures; furthermore, the subsequent
installation must be performed correctly and safely in accordance with the instructions given.
■ Be sure to give this instruction manual to the customer once installation is complete.
■ When unit is installed vertically, follow below instructions. For items not described in this section, follow the instructions in Lossnay
unit manuals. LGH-15 to 100RVX3-E are allowed to be installed vertically, only in the direction the maintenance cover faces up. Use
optional parts PZ-1/2VS-E for vertical floor installation, otherwise installer shall ensure the safety during the lifetime of the unit.
1. Safety Precautions
The following signs indicate that death or serious injury may be caused by failure to heed the precautions described below.
WARNING
Install the unit on the floor which is flat and have enough strength.
Make sure the unit is always touching to the floor certainly.
Otherwise, it could cause injury.
Always make the fall prevention by using upper ceiling suspension fixture of the unit. In case of using anchor
bolts embedded to the wall, choose the anchor bolts of M10 or M12. Install the anchor to the enough strong
The instructions
wall.
given must be
followed.
Do not use the PZ-1/2VS-E in a corrosive environment, such as where it gets wet.
The product may tip over and cause injury.
CAUTION
Make sure to install the unit where users cannot touch it easily, for example in the machine room.
Otherwise there is a risk of burns and injuries.
Make a protection to the edges and areas that may be touched during maintenance.
Do not install the unit in contact with the wall directory for avoiding any problem of vibration, wall discoloration
and condensation water.
Do not put anything on the unit.
Do not install unit in the place where water can come to the unit from above, such as under the drainage ducts.
It could cause fire or electrical shock.
When using the product where it is exposed to low temperatures or high humidity, additional heat insulation on
the unit are necessary which is a closed-cell foam with a thickness of 3 mm or more.
Filters and Lossnay cores can be withdrawn out even when the unit is installed vertically, but when replacing
fans and GM, the unit must be laid down and placed horizontally. Install the unit where horizontal maintenance
space can be secured around it and use enough length of cables and detachable ducts so that the unit can be
The instructions
given must be
laid down. The required space is shown in the product outline drawing.
followed.
Installation gradient tolerance should be 0±1°, same as horizontal installation.
If the unit causes vibration problem, use anti-vibration countermeasures such as a rubber sheet between the
PZ-1/2VS-E and the floor.
When installing vertically, do not install elbow duct facing the floor near the RA suction port of the unit. When
installing a downward bending duct or a damper on the RA, please install it at least 3 m away from the product
so as not to generate turbulence in the RA duct.
Otherwise, the unit may not work properly.
Do not lean on or put your weight on the product.
There is a risk of product deformation or injury.
When inserting or removing Lossnay cores, securely hold the handle until the end and insert or remove them
one by one.
Otherwise, some parts might be damaged.
Applicable model
Incorrect handling could cause serious injury or death.
Incorrect handling could cause injury or damage to property or household effects.
For dealers and installation contractors
2301876HG4201
Advertisement
Related Manuals for Mitsubishi Electric PZ-1VS-E
Summary of Contents for Mitsubishi Electric PZ-1VS-E
- Page 1 2301876HG4201 FLOOR STANDING SUPPORT PLATE FOR LOSSNAY Applicable model MODEL PZ-1VS-E LGH-15 to 50RVX3-E PZ-2VS-E LGH-65 to 100RVX3-E Installation Manual For dealers and installation contractors ■ This manual must be read both fully and carefully before commencing installation procedures; furthermore, the subsequent installation must be performed correctly and safely in accordance with the instructions given.
- Page 2 Remove both ceiling suspension fixtures near RA inlet and EA outlet by loosening M6 screws of each before standing the unit. Wall Screw (M6) PZ-1VS-E for LGH-15 to 50RVX3-E PZ-2VS-E for LGH-65 to 100RVX3-E Ceiling suspension fixtures Screw (M6) Ceiling suspension fixtures NOTE ◦...
- Page 3 Related Links Model Number: LGH-200RVX3-E LGH-15-200RVX3-E Declaration of Conformity (N22HHGT0011) LGH-15-200RVX3-E Installation Manual (N22HHZA0013) LGH-15-200RVX3-E Instruction Book (N22HHZA0012) LGH-15-200RVX3-E Service Manual (U318) LGH-200RVX3-E Specification Sheet (N22HHGU0009A) LGH-RVX3-E Infographic LGH-RVX3-E Product Information Sheet Lossnay Weatherproof Housing LGH-150-200RVX3 Installation Manual PZ-1-2VS-E Installation Manual (876HG4201) PZ-4GS-E Installation Manual (876H65501) PZ-70CSD-E Installation Manual (876HG4001) PZ-70CSW-E Installation Manual (876H65401)
- Page 4 Related Links Model Number: LGH-200RVX3-E...