Advertisement
Quick Links
Advertisement
Related Manuals for Asus FX507V
Summary of Contents for Asus FX507V
- Page 1 ASUS TUF Gaming F15 (FX507V) series Service Guide...
- Page 2 LIMITATION OF LIABILITY Circumstances may arise where because of a default on ASUS’ part or other liability, you are entitled to recover damages from ASUS. In each such instance, regardless of the basis on which you are entitled to claim damages from ASUS, ASUS is liable for no more than damages for bodily injury (including death) and damage to real property and tangible personal property;...
- Page 3 Disclaimer ASUS is not responsible for direct, indirect, intentional or unintentional damages resulting from improper installation and operation. Safety precautions • Keep liquids or moisture away from your Notebook PC before installing or removing any components. • Ensure to place your Notebook PC on a stable surface before installing or removing any components.
- Page 4 Table of Contents ⚫ Service Overview ⚫ ASUS TUF Gaming F15 (FX507V) Series Overview ⚫ Components Top View ⚫ Components Bottom View ⚫ Repair Overview ⚫ Appropriate Tools ⚫ Key Parts and Related Parts ⚫ Disassembly steps : • BASE CASE •...
- Page 5 Service Overview • Carefully read through this Service Guide for a look at various components of the device before performing any service and repairs. • To provide the best service, we have provided the below information for technicians from distributors and resellers to perform the complete device disassembly and assembly.
- Page 6 ASUS TUF Gaming F15 (FX507V) Series Overview Top View Bottom View ❶ Array microphones ❷ Camera indicator ❸ Camera ❶ Air vents ❹ Display panel ❷ Audio speakers ❺ Status indicators ❸ Bottom cover ❻ Keyboard ❼ Capital lock indicator ❽...
- Page 7 Components Top View ⧫ ESD AIR DISCHARGE ⧫ LCD COVER ⧫ BASE CASE ⧫ DDR4 / DDR5 ⧫ GPU FAN ⧫ CPU FAN ⧫HINGE L / R ⧫ DIMM COVER MYLAR ⧫ USB BD GASKET ⧫ CAMERA ⧫ LCD BEZEL ⧫...
- Page 8 Components Bottom View ⧫ LCD COVER ⧫ KEYBOARD MODULE ⧫ THERMAL MODULE ASSY LCD COVER TAPE ⧫ LCD BEZEL ⧫ WIFI ANTENNA ⧫ LED BD ⧫ANTENNA FIX ACETATE CLOTH ⧫ 15.6‘ LCD PANEL ⧫ DDR AL FOIL MYLAR ⧫ USB BD ⧫...
- Page 9 Repair Overview This chapter describes disassembly and assembly (Assemble document please look up from the last page), please follow the information provided in this section to perform the complete disassembly procedure. ⧫ Precautions: Before you perform any service or repair on the notebook, please pay special attention to the cautions prevent any damages to the notebook. 1.
- Page 10 Appropriate Tools Please prepare and select the appropriate tools to disassemble/assemble for the ASUS TUF Gaming F15 (FX507V) series notebook. ⧫ Alcohol 95 ⧫ Glove ⧫ Dust-free Cloth Screwdriver Please accord to different screw specification to choose different screwdriver and head.
- Page 11 BASE CASE The device has an Ambient Light Sensor (ALS) for power-off protection Function. Disassembly Notice Ambient Light Sensor (ALS): Step 1 : Remove the screws *11 pcs and *1pc in case. 1. After removing the BOTTOM CASE, the ambient light sensor Step 2 : Use the plastic blade to pry the base case.
- Page 12 DISSCONNECT BATTERY The device has an Ambient Light Sensor (ALS) for power-off protection Function. Disassembly Notice Step 1 : Use the non-conductive pry tool to push iron sheet. Step 2 : Use the non-conductive pry tool to disconnect battery connector. Please disconnect the red cable side first! Back...
- Page 13 The device has an Ambient Light Sensor (ALS) for power-off protection Function. Disassembly Notice Step 1 : Tear off the DIMM COVER MYLAR *1pc. Screws Spec Torque (kgf-cm) Step 2 : Remove the screws *2pcs. M2*3L (5.6,0.8)(K)#1 1.5±0.2 Step 3 : Remove the SSD at left side and remove the AL FOIL and tear off the ABSORBER from SSD. Step 4 : Remove the SSD at right side and tear off the ABSORBER from SSD.
- Page 14 Assembly Notice The device has an Ambient Light Sensor (ALS) for power-off protection Function. When installing the SSD, please keep the SSD less then 15 degrees Please use left- SSD slot as first priority. with motherboard, and then insert the SSD. SSD1 >15°...
- Page 15 The device has an Ambient Light Sensor (ALS) for power-off protection Function. Disassembly Notice Assembly Notice Please paste ABSORBERS on the front and Step 1 : Tear off the AL FOIL MYLAR *1pc. back sides of RAM before installing the Memory Module. Step 2 : Unlock and remove the RAM module *2pcs (red mark).
- Page 16 BATTERY Disassembly Notice Step 1 : Remove the screws*3pcs (red circles) from battery, then lift the BATTERY to remove it. Step 2 : Remove the BATTERY CABLE from BATTERY. Screws Spec Torque(kgf-cm) M2*4L(5,0.8) (K) #1 2.0±0.2 Remove the screws Remove Battery (90W) Back...
- Page 17 USB BD The device has an Ambient Light Sensor (ALS) for power-off protection Function. Disassembly Notice Step 1 : Disconnect the USB FPC connector (yellow mark) and remove the USB FPC. Screws Spec Torque (kgf-cm) Step 2 : Remove the screw*1pc and remove the USB BD. M2*3L(5.6,0.8)(K)#1 2.0±0.2 Disconnect...
- Page 18 WIFI CARD The device has an Ambient Light Sensor (ALS) for power-off protection Function. Disassembly Notice Step 1 : Disconnect the RF CABLE connector*2pcs(red Mark). Step 2 : Remove the screw*1pc(blue circle). Screws Spec Torque (kgf-cm) Step 3 : Remove the WIFI CARD. M2*3L(5.6,0.8)(K)#1 2.0±0.2 Remove...
- Page 19 FAN (with THERMAL MODULE and MAIN BOARD) The device has an Ambient Light Sensor (ALS) for power-off protection Function. Disassembly Notice Assembly Notice Step 1 : Disconnect the connectors*8pcs (yellow mark) and release EDP cable tape (orange mark). Step 2 : Remove the screws*9pcs (red mark). Please use the correct way to take fans off, avoiding getting out of Step 3 : Remove the MB with Thermal and FAN module.
- Page 20 THERMAL MODULE The device has an Ambient Light Sensor (ALS) for power-off protection Function. Disassembly Notice Step 1 : Please follow the reverse screws numbers to remove screws*8pcs. Torque Screws Spec Step 2 : Remove the THERMAL MODULE from MB. (kgf-cm) M2*4L (5,0.8) (K) #1 2.0±0.2...
- Page 21 MAIN BOARD Mainboard connector placement BATTERY LED/MB FFC GPU FAN USB/MB FPC EDP CABLE KB BL FPC K/B FPC CPU FAN Supports using JIG BOARD to TP/MB FFC SPEAKER refresh F1 BIOS. Back...
- Page 22 MAIN BOARD Parts marked in yellow can be ordered/replaced Materials on mainboard separately at L2 repair level. When L3/L4 repair finished, no need to paste new one if shortage of this material on the MB. TOP SIDE FX507VU GPU E5 ABSORBER FA506IV N18E CPU ABSORBER FX507VU CPU BKT ASSY FX507ZE G20 GPU ABSORBER...
- Page 23 MAIN BOARD FA507VU SMT GSAKET 2-2-2 Parts marked in yellow can be ordered/replaced Materials on mainboard separately at L2 repair level. When L3/L4 repair finished, no need to paste new one if shortage of this material on the MB. FA507VU GSAKET LPG-S 3-5-4 TOP SIDE GA402XY SMT GSAKET L2.5*H3.5*W3 Choose by GPU/VGA CHIP Model...
- Page 24 LED BD The device has an Ambient Light Sensor (ALS) for power-off protection Function. Disassembly Notice Step 1 : Release the Mylar (yellow mark). Assembly Notice Step 2 : Release the Gasket. Step 3 : Remove the LED BD with LED FFC. If FFC is damage during disassembly, please replace new one.
- Page 25 TOUCHPAD MODULE The device has an Ambient Light Sensor (ALS) for power-off protection Function. Disassembly Notice Step 1 : Disconnect the TP FFC connector (red mark) and remove the TP FFC. Screws Spec Torque (kgf-cm) Step 2 : Remove the screws*3pcs and take out the Touchpad. M2*2L(6.2,0.55)(K)#1 2.0 ±0.2 Remove...
- Page 26 SPEAKER The device has an Ambient Light Sensor (ALS) for power-off protection Function. Disassembly Notice Step 1 : Remove the SPEAKER. Assembly Notice For Speaker assembly, please follow the yellow mark below to tidy up cable. Remove Back...
- Page 27 KEYBOARD MODULE The device has an Ambient Light Sensor (ALS) for power-off protection Function. Disassembly Notice Step 1 : Remove the screws*4pcs (red mark). Screws Spec Torque (kgf-cm) Assembly Notice Step 2 : Open and remove the KEYBOARD MODULE. M2.5*5L(K)B-ZN NY#1 2.5±0.2 Please refer below picture to organize EDP cable while repair device, it’s to keep device safety.
- Page 28 LCD BEZEL The device has an Ambient Light Sensor (ALS) for power-off protection Function. Disassembly Notice Step 1 : Remove the BEZEL COSMETIC MYLAR*2pcs. Screws Spec Torque (kgf-cm) Step 2 : Remove the screws*2pcs. M2.5*3.5L(4.5,0.5)(K)#1 2.50±0.2 Step 3 : Remove the LCD BEZEL. Step 3-4 Due to some tapes behind the lower edge of bezel, please using plastic blade to teardown the bezel.
- Page 29 LCD PANEL The device has an Ambient Light Sensor (ALS) for power-off protection Function. Disassembly Notice Step 1 : Remove the screws*4pcs and remove the hinges*2pcs. Screws Spec Torque (kgf-cm) Step 2 : Pull out the LCD adhesive*2pcs. M2.5*3L #1 2.50±0.2 Step 3 : Remove the LCD PANEL.
- Page 30 LCD COVER The device has an Ambient Light Sensor (ALS) for power-off protection Function. Disassembly Notice Assembly Notice Step 1 : Release the Gasket (red mark). Step 2 : Disconnect (green mark) and remove the EDP cable. Please follow the green mark to tidy up EDP cable. Step 3 : Use the non-conductive pry tool to insert from below and slide to the left then remove the CAMERA.
- Page 31 LCD PANEL and LCD Cover The device has an Ambient Light Sensor (ALS) for power-off protection Function. Assembly Notice Assembly Notice When assembly the LCD PANEL : When reuse the LCD PANEL or BEZEL : Please use the fingertip to clean the residual glue on PANEL or BEZEL. Step 1 : Remove release paper of LCD Adhesive*2pcs.