Page 1
OPERATING INSTRUCTIONS MODE D’EMPLOI MANUAL DE FUNCIONAMIENTO TX-43LX650E TX-50LX650E TX-55LX650E TX-65LX650E TX-43LX650EZ TX-50LX650EZ TX-55LX650EZ TX-65LX650EZ TX-43LX660E TX-50LX660E TX-55LX660E TX-65LX660E TX-43LX670E TX-50LX670E TX-55LX670E TX-65LX670E LED TV Téléviseur LED Televisor LED You can find instructions for your TV’s features in the E-Manual. To access the E-Manual, enter Settings menu, select Manuals and press OK.
Picture .............34 Table of Contents Subtitle.............34 Safety Information ..........2 Supported DVI Resolutions ......... 35 IMPORTANT - Please read these instructions fully Specification ............36 before installing or operating ......... 2 Notice ..............37 Markings on the Product ........2 Licences ..............
• Do not expose the TV to direct sunlight or do not Safety Information place open flames such as lit candles on the top of or near the TV. • Do not place any heat sources such as electric CAUTION heaters, radiators, etc.
Page 4
WARNING Do not ingest the battery, Chemical Burn Hazard WALL MOUNTING WARNINGS This product or the accessories supplied with the prod- • Read the instructions before mounting your TV uct may contain a coin/button cell battery. If the coin/ on the wall. button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Maintenance Assembling / Removing the pedestal First, remove the mains plug from the mains socket. Preparations Display panel, Take out the pedestal(s) and the TV from the packing case and put the TV onto a work table with the screen Cabinet, Pedestal panel down on the clean and soft cloth (blanket, etc.) Regular care:...
When using the wall- them gently until the stand is properly fitted. hanging bracket 43” 50/55/65” Please contact your local Panasonic dealer to purchase the recommended wall-hanging bracket. Holes for wall-hanging bracket installation; Rear of the TV M4 x 12 mm...
High Dynamic Range (HDR) / Hybrid Log- Introduction Gamma (HLG) Using this feature the TV can reproduce greater Thank you for choosing our product. You’ll soon be dynamic range of luminosity by capturing and then enjoying your new TV. Please read these instructions combining several different exposures.
Antenna Connection Connect the aerial or cable TV plug to the AERIAL INPUT (ANT) socket located on the left side of the TV or satellite plug to the SATELLITE INPUT (LNB) socket located on the rear side of the TV. Left side of the TV Rear side of the TV If you want to connect a device to the TV, make...
Other Connections If you want to connect a device to the TV, make sure that both the TV and the device are turned off before making any connection. After the connection is done, you can turn on the units and use them. When using the wall mounting kit Connector Type...
The joystick allows you to control the Volume / Turning On/Off the TV Programme / Source and Quick Standby-On functions of the TV. Connect power Note: The position of the joystick may differ depending on IMPORTANT: The TV set is designed to operate on the model.
16. Coloured Buttons: Follow the on-screen instructions for coloured button functions 17. Pause: Pauses the media being played Note: Other Panasonic devices cannot be operated with Play: Starts to play selected media this remote. 18. Text: Opens and closes teletext (where available in...
network and press OK if you want to use wireless Initial Setup Wizard connection instead of wired connection. Note: Follow the on-screen instructions to complete the initial 6. Network Connection setup process. Use the directional buttons and the OK button You will be directed to the next step automatically, if on the remote to select, set, confirm and proceed.
Page 13
OK on the remote to confirm and proceed. You can environment. This option is intended only for store also view Terms of Service, Privacy Policy and use. It is recommended to select Home for home use. Play Terms of Service on this screen. To display the 13.
If Satellite option is selected, Antenna Type screen LNB Configurations: Set the parameters for LNB. will be displayed next. If you have a Direct satellite For DiSEqC antenna type select the correct DiSEqC system, you can proceed to the next step quickly by port corresponding to your satellite system.
Screen. You can also select the Android TV Home and recommendations from streaming apps. In the option from the Inputs menu to switch to Home Discover tab recommendations from streaming Screen. To open the Inputs menu, press the Source services will be displayed. In the Apps tab, all the button on the remote or press the Menu button on the apps installed on your TV will be displayed and you remote when the TV is in Live TV mode, highlight the...
Page 16
set input source. Define a time after which you want Persistent Storage: Turn the Persistent Storage your TV to turn itself off or set as Off to disable. function on or off. If set as On cookies will be stored with an expiry date in the persistent Auto Sleep: Define an idle time after which you memory of the TV.
Channel Scan: Start a scan for digital terrestrial Settings channels. You can press the Back/Return button to cancel the scan. The channels that have already been You can access the Settings menu from the Home found will be stored in the channel list. Screen or from the TV options menu in Live TV mode.
Page 18
You can press the Blue button to delete the highlighted move and press OK to select. Then do the same for a channel. second channel. When the second channel is selected, you can press the Blue button and the first selected Channel Delete: Highlight the desired channel/s on channel will be moved to the position of that channel.
be able to configure these settings before the scan. If Note: Some options may not be available and appear as greyed out depending on the operator selection and operator Channel Installation Mode is set to Preferred Satel- related settings. lite this option may be named differently depending on the available services.
TV. Highlight a service listed in the Choose synced Device Preferences apps section and press OK to enable/disable data sync. Highlight Sync now and press OK to sync all About: Check for system updates, change the device enabled services at once. name, reset the TV to the factory defaults and display system information such as network addresses, Add account: Add a new one to available accounts...
Page 21
for HDMI CEC (Consumer Electronic Control) function Sharpness: Adjust the sharpness value for the and display the CEC device list. objects displayed on the screen. Power: This menu has the same options as in TV Gamma: Set your gamma preference. Dark, Middle Options>Power menu.
Page 22
Blue Stretch: Human eye perceives cooler whites to source signal type. When set as Off, the TV’s as brighter white, Blue Stretch feature changes maximum colour capacity is used by default. White balance of mid-high grey levels to cooler Colour Tuner: Colour saturation, hue, brightness colour temperature.
Page 23
Downmix Mode: Set your preference to convert mul- instructions and read the information displayed on ti-channel audio signals to two-channel audio signals. the screen before proceeding. Press OK to see the options and set. Stereo and Note: Formatting the connected storage device will erase Surround options will be available.
Screen Saver: Set the screensaver options for your Remote & Accessories TV. You can choose a screensaver, set wait time for the screensaver or start the screensaver mode. You can use wireless accessories, such as your remote control (depends on the model of the remote control), Energy Saver: Define a time after which you want headphones, keyboards or game controllers with your your TV to turn itself off for energy saving.
Editing the Channels and the Channel List Programme Guide You can edit the channels and the channel list using the Channel Skip, Channel Swap, Channel Move, By means of Electronic Programme Guide (EPG) Channel Edit and Channel Delete options under the function of your TV, you can browse the event schedule Settings>Channel>Channels menu.
Wireless Connection Connecting to the Internet A wireless LAN modem/router is required to connect the TV to the Internet via wireless LAN. You can access the Internet via your TV, by connecting it to a broadband system. It is necessary to configure Highlight Wi-Fi option in the Network &...
values for the wireless standards. They are not the image press the Menu button while the photo file of actual speeds of data transmission. your choice is displayed, highlight Photo Frame Image and press OK. The location where the transmission is most effective differs depending on the usage environment.
slide show will stop after the last listed file is displayed Rotate: Rotate the image. The image will be rotated and media player screen will be displayed. 90 degrees clockwise each time you press OK. You can also press the Green button to rotate. This option Info: Display the info bar.
to the device. Only devices that support CEC Remote formatted devices with a storage capacity larger than 2TB are not supported. Files larger than 4 GB are not supported. Control function will respond to the TV remote control. You can view your photos, text documents or play your The TV supports also eARC (Enhanced Audio Return music and video files installed on a connected USB Channel) feature.
Highlight Device name and press OK. Then highlight HbbTV applications use the buttons on the remote Change and press OK again. You can either select control to interact with the user. When an HbbTV one of the predefined names or enter a custom name. application is launched, the control of some buttons are owned by the application.
• Disconnect the power cord from the power outlet. • Make sure that the TV audio output is connected to Wait for one minute then reconnect it. the audio input on the external sound system. • Press the Standby/On button on the TV. •...
Picture Resolution Image Photo (width x height) Base-line 15360 x 8640 JPEG Progressive 1024 x 768 Non-Interlace 9600 x 6400 Interface 1200 x 800 9600 x 6400 6400 x 4800 WebP 3840 x 2160 HEIF 4000 x 3000 Subtitle Internal File Extension Container Subtitle Codec...
Supported DVI Resolutions When connecting devices to your TV’s connectors by using a DVI converter cable (DVI to HDMI cable - not supplied), you can refer to the following resolution information. 56Hz 60Hz 66Hz 70Hz 72Hz 75Hz 640x480 800x600 1024x768 1280x768 1280x960 1360x768...
Display 16/9 43” 16/9 50” 16/9 55” 16/9 65” Operation temperature and 0ºC up to 40ºC, 85% humidity max operation humidity For more product information, please visit EPREL: https://eprel.ec.europa.eu. EPREL registration number is available on https://eprel.panasonic.eu/product. English - 36 -...
It’s recommended that user checks with local discontinued at any time. authorities for the current status of their national reg- ulations for 5 GHz wireless LAN’s. Panasonic assumes no responsibility and makes no warranty for the availability or the continuity of the Standard services.