Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear safety
instruction
footwear
manual
1.
SAFETY
Only open bottomed Euro type pallets can be used with this truck
DO NOT use a faulty or damaged truck.
8
Before using the truck all parts and working mechanisms should be checked for wear or damage. Pay particular attention to the wheels,
handle and fork lifting and lowering mechanism. Any parts found to be worn, damaged or suspect should be repaired or replaced before
the truck is used.
All repairs must be carried out by an authorised Sealey service agent.
Personnel who operate the truck and those in the vicinity of operation should wear safety footwear with reinforced toe caps at all times.
DO NOT allow persons other than the operator to stand in front of or behind the truck when it is moving, lifting or lowering.
8
Never place any part of your body in the lifting mechanism or under the forks or load. DO NOT place a foot in front of a rolling wheel injury
could result.
DO NOT allow others to ride on the truck.
8
DO NOT lift or move unstable or loosely stacked loads.
8
Take extra care when operating a loaded truck in high winds.
Take special care when moving long, high or wide loads in order not to dislodge the load by striking any fixtures, vehicles or people in the
area of operation.
Always ensure that the load is evenly distributed across the forks
with the centre of the load being at the halfway point of the length of
the forks.
DO NOT overload the truck - refer to the specification for maximum
8
permitted load.
If a load is left unattended even for a very short period of time it
should be lowered to the ground.
When not in use the truck should be left in the lowered position.
Ensure that the width and length of the forks is correct for the pallet
to be lifted.
Ensure that the truck is sufficiently inserted into the pallet to lift the
full width of the pallet.
Use the truck on level, flat, hard surfaces and in well lit areas.
DO NOT use truck on sloping or uneven ground; DO NOT attempt
8
to negotiate curbs, steps or ramps. Be aware of differences in floor
levels.
DO NOT use the truck in explosive atmospheres.
8
DO NOT use the truck if you are unsure of the stability of the truck.
8
The operator of the truck must be physically capable of controlling
the load selected; particularly in relation to stopping a rolling load.
DO NOT modify the truck.
8
2.
INTRODUCTION
Heavy-duty high lift pallet truck suitable for the loading/unloading
of light commercial vehicles as well as warehouse/general
handling duties. Features twin stabilisers for extra balance when
at maximum lift and an ergonomic handle design for comfortable
operation.
3.
SPECIFICATION
Model No: ................................................... PT1170H.V3
Capacity: ............................................................. 1000kg
Fork Spread: ....................................................... 225mm
© Jack Sealey Limited
LIFT PALLET TRUCK - 1000KG CAPACITY
MODEL NO:
DO NOT get
DO NOT ride
under truck
on truck
Original Language Version
PT1170H.V3
DO NOT
reach in
CONTENTS
1
Chassis
2
Tiller
3
Hydraulic Cylinder and Pump
Numbers in brackets not applicable to this model
Forks (Length x Overall Width: .................1170 x 540mm
Maximum Height: ................................................ 800mm
Minimum Height: ................................................... 85mm
fig.1
4
Steering Wheel
5
Scissors
6
Control Lever
PT1170H.V3
Issue 3
15/08/23
Advertisement
Related Manuals for Sealey PT1170H.V3
Summary of Contents for Sealey PT1170H.V3
- Page 1 PT1170H.V3 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 4.7.4. The lashing points are according to the fi g.4 4.7.5. For transportation, remove the load, lower the truck to the lowest position and lash it safe with dedicated lashing straps. Original Language Version PT1170H.V3 Issue 3 15/08/23 © Jack Sealey Limited...
- Page 3 Clean the dust from the surface of the release valve (part no. 321 on Parts List). ANNUALLY Change the oil (more frequently if colour has substantially darkened or feels gritty). Use Sealey hydraulic oil or one that conforms to it. Check all parts of the truck for wear and replace defective parts where necessary.
- Page 4 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 sales@sealey.co.uk...