Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS &
CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO
SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE
Refer to
Wear eye
instructions
protection
1.
SAFETY
WARNING! Ensure all Health and Safety, local authority, and general workshop practice regulations are strictly adhered to when using tools.
‰
DO NOT use tools if damaged or worn.
8
Maintain the tools in good and clean condition for best and safest performance.
9
Ensure all threads are clean and well lubricated, especially the thrust bolt.
9
Always check that the puller is correctly assembled and is square with the workpiece.
9
If the vehicle is raised, ensure it is adequately supported with axle stands, ramps, etc. as appropriate.
9
Wear suitable clothing to avoid snagging. DO NOT wear jewellery. Tie back long hair.
9
Wear approved eye protection. A full range of personal safety equipment is available from your Sealey stockist.
9
Where possible shield the workpiece with canvas or similar to provide protection against failed parts.
9
DO NOT heat puller jaws when heating a gear or bearing as this will affect the temper and, therefore, the strength of the material.
8
DO NOT use air tools to turn the thrust bolt. Always keep thrust bolt well lubricated.
8
DO NOT hit the workpiece or ram with a hammer if the workpiece has not moved with maximum puller force applied. Use a larger
8
capacity puller.
Account for all tools and parts being used and DO NOT leave them in or on the vehicle.
9
IMPORTANT: Always refer to the vehicle manufacturer's service instructions, or proprietary manual, to establish the correct procedure
and data. These instructions for use are provided as a guide only.
2.
INTRODUCTION
Mechanical puller set with Ø25-50mm and Ø45-75mm separators and single yoke with 170mm thrust bolt. Suitable for engineering,
automotive, marine and agricultural applications. Supplied in storage case.
3.
CONTENTS
ITEM
PART NO.
1
PS987*
2
PS986**
3
PS984-V4-03
4
PS984-V4-04
5
PS984-V4-05
6
PS984-V4-06
7
PS984-V4-07
8
PS984-V4-08
* PS987 is a replacement separator with Ø50-75mm
** PS986 is a replacement separator with Ø30-50mm
© Jack Sealey Limited
MECHANICAL BEARING SEPARATOR/PULLER
SET 12PC
MODEL NO:
Wear protective
Wear safety
gloves
footwear
DESCRIPTION
Ø45-75mm separators
Ø25-50mm separators
Cross Beam 160mmL
Thrust Bolt 170mmL
Rod Extension 90mmL (Double Thread)
Rod Extension 115mmL
Rod Extension 60mmL (Double Thread)
Rod Extension 85mmL
Original Language Version
PS984.V4
Wear protective
clothing
1
4
3
6
8
PS984.V4
Issue 1
2
5
7
05/12/23
Advertisement
Related Manuals for Sealey PS984.V4
Summary of Contents for Sealey PS984.V4
- Page 1 PS984.V4 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS &...
- Page 2 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 sales@sealey.co.uk...