Advertisement
Refer to Safety chapters.
Refer to installation instruction document to install your appliance.
Fix the appliance in accordance with installation instruction document to avoid a risk of instability of the appliance. |
Overall dimensions ¹ | ||
H1 | mm | 1441 |
W1* | mm | 548 |
D1 | mm | 549 |
¹ the height, width and depth of the appliance without the handle
* including the width of the bottom hinges (8 mm)
Space required in use ² | ||
H2 (A+B) | mm | 1482 |
W2* | mm | 548 |
D2 | mm | 551 |
A | mm | 1446 |
B | mm | 36 |
² the height, width and depth of the appliance including the handle, plus the space necessary for free circulation of the cooling air
* including the width of the bottom hinges (8 mm)
Overall space required in use ³ | ||
H3 (A+B) | mm | 1482 |
W3* | mm | 548 |
D3 | mm | 1071 |
³ the height, width and depth of the appliance including the handle, plus the space necessary for free circulation of the cooling air, plus the space necessary to allow door opening to the minimum angle permitting removal of all internal equipment
* including the width of the bottom hinges (8mm)
To ensure appliance's best functionality, you should not install the appliance in a place with direct sunlight. Do not install the appliance close to radiators or cookers, ovens, or hobs, unless otherwise specified in the installation instructions.
Make sure that air can circulate freely around the back of the cabinet.
This appliance should be installed in a dry, well ventilated indoor position.
This appliance is intended to be used at ambient temperature ranging from 10°C to 38°C.
The correct operation of the appliance can only be guaranteed within the specified temperature range. |
If you have any doubts regarding where to install the appliance, please turn to the vendor, to our customer service or to the nearest Authorised Service Centre. |
It must be possible to disconnect the appliance from the mains power supply. The plug must therefore be easily accessible after installation. |
Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. |
This appliance must be earthed. The manufacturer declines any liability should these safety measures not be observed. |
The wires in the mains lead are coloured in accordance with the following code:
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard.
Ensure that it is disposed of safely.
The airflow behind the appliance must be sufficient.
Refer to the installation instructions for the installation.
Please refer to the separate document with instructions on installation and door reversal.
At every stage of reversing the door protect the floor from scratching with a durable material. |
Keep touching the ON/OFF button (6) for 3 seconds.
All indicators light off.
Before regulating the temperature, it is necessary to select the compartment (fridge or freezer).
The upper or lower cavity is selected by the compartment selection button (6).
To select the freezer compartment touch the compartment selection button (6) until LED corresponding to the lower cavity lights up.
The temperature LED indicator shows the latest set temperature. Recommended setting is -18°C.
To select the fridge compartment touch the compartment selection button (6) until LED corresponding to the upper cavity lights up.
The temperature LED indicator shows the latest set temperature. Recommended setting is +4°C.
To set temperature:
The set temperature will be reached within 24 hours. After a power failure the set temperature remains stored.
The FastFreeze function is used to perform pre-freezing and fast freezing in sequence in the freezer compartment. This function accelerates the freezing of fresh food and, at the same time, protects food products already stored in the freezer compartment from undesirable warming.
To freeze fresh food activate the FastFreeze function at least 24 hours before placing the food to complete prefreezing. |
To activate FastFreeze function press the FastFreeze button (7) for 3 seconds. The FastFreeze indicator switches on.
This function stops automatically after 52 hours. |
It is possible to deactivate the function at any time by pressing FastFreeze button (7) for 3 seconds again. The FastFreeze indicator switches off.
When there is a temperature increase in the freezer compartment (for example due to an earlier power failure), the freezer compartment indicator flashes and the sound is on.
To deactivate the sound press any button.
The freezer temperature indicator LED continues to flash until the normal conditions are restored.
If you do not press any button, the sound switches off automatically after around one hour to avoid disturbing.
If the fridge door is left open for approximately 5 minutes, the fridge compartment indicator flashes and the sound is on.
During the alarm the sound can be muted by pressing any button. The sound switches off automatically after around one hour to avoid disturbing.
The alarm deactivates after closing the door.
To permit storage of food packages of various sizes, the door shelves can be placed at different heights.
The walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired.
Do not move the glass shelf above the vegetable drawer to ensure correct air circulation. |
There are special drawers in the bottom part of the appliance suitable for storage of fruits and vegetables.
The freezer compartment is suitable for freezing fresh food and storing frozen and deep-frozen food for a long time.
To freeze fresh food activate the FastFreeze function at least 24 hours before placing the food to be frozen in the freezer compartment.
Store the fresh food evenly distributed in the first compartment or drawer from the top.
The maximum amount of food that can be frozen without adding other fresh food during 24 hours is specified on the rating plate (a label located inside the appliance).
When the freezing process is complete, the appliance automatically returns to the previous temperature setting (see "FastFreeze function").
For more information refer to "Hints for freezing".
When activating an appliance for the first time or after a period out of use, before putting the products in the compartment let the appliance run at least 3 hours with the FastFreeze function switched on.
The freezer drawers ensure that it is quick and easy to find the food package you want.
If large quantities of food are to be stored, remove all drawers and place the food on shelves.
Keep the food no closer than 15 mm from the door.
In the event of accidental defrosting, for example due to a power failure, if the power has been off for longer than the value shown on rating plate under "rising time", the defrosted food must be consumed quickly or cooked immediately then cooled and then re-frozen. Refer to "High temperature alarm". |
Deep-frozen or frozen food, prior to being consumed, can be thawed in the refrigerator or inside a plastic bag under cold water.
This operation depends on the time available and on the type of food. Small pieces may even be cooked still frozen.
This appliance is equipped with one or more trays for the production of ice-cubes.
Do not use metallic instruments to remove the trays from the freezer. |
After grocery shopping:
Type of food | Shelf life (months) | ||||
Bread | 3 | ||||
Fruits (except citrus) | 6 - 12 | ||||
Vegetables | 8 - 10 | ||||
Leftovers without meat | 1 - 2 | ||||
Dairy food: | |||||
Butter Soft cheese (e.g. mozzarella) Hard cheese (e.g. parmesan, cheddar) | 6 - 9 3 - 4 6 | ||||
Seafood: | |||||
Fatty fish (e.g. salmon, mackerel) Lean fish (e.g. cod, flounder) Shrimps Shucked clams and mussels Cooked fish | 2 - 3 4 - 6 12 3 - 4 1 - 2 | ||||
Meat: | |||||
Poultry Beef Pork Lamb Sausage Ham Leftovers with meat | 9 - 12 6 - 12 4 - 6 6 - 9 1 - 2 1 - 2 2 - 3 |
Refer to Safety chapters. |
Before using the appliance for the first time, the interior and all internal accessories should be washed with lukewarm water and some neutral soap to remove the typical smell of a brand-new product, then dried thoroughly.
Do not use detergents, abrasive powders, chlorine or oil-based cleaners as they will damage the finish.
The accessories and parts of the appliance are not suitable for washing in a dishwasher. |
The equipment has to be cleaned regularly:
Frost is automatically eliminated from the evaporator of the refrigerator compartment during normal use. The defrost water drains out through a trough into a special container at the back of the appliance, over the motor compressor, where it evaporates.
It is important to periodically clean the defrost water drain hole in the middle of the refrigerator compartment channel to prevent the water overflowing and dripping onto the food inside.
For this purpose use the tube cleaner provided with the appliance.
Never use sharp metal tools to scrape off frost from the evaporator as you could damage it. Do not use a mechanical device or any artificial means to speed up the thawing process other than those recommended by the manufacturer. Do not use the supplied ice scraper to prepare food. |
About 12 hours prior to defrosting set a lower temperature in order to build up sufficient chill reserve in case of any interruption in operation. |
A certain amount of frost will always form on the freezer shelves and around the top compartment.
Defrost the freezer when the frost layer reaches a thickness of about 3-5 mm.
A temperature rise of the frozen food packs during defrosting may shorten their safe storage life. Do not touch frozen goods with wet hands. Hands can freeze to the goods. |
Only after this time put the food back into the freezer compartment.
When the appliance is not in use for long period, take the following precautions:
Refer to Safety chapters. |
Problem | Possible cause | Solution |
The appliance does not operate. | The appliance is switched off. | Switch on the appliance. |
The mains plug is not connected to the mains socket correctly. | Connect the mains plug to the mains socket correctly. | |
There is no voltage in the mains socket. | Connect a different electrical appliance to the mains socket. Contact a qualified electrician. | |
The appliance is noisy. | The appliance is not supported properly. | Check if the appliance stands stable. |
Acoustic or visual alarm is on. | The cabinet has been recently switched on. | Refer to "High temperature alarm" or "Door open alarm". |
The temperature in the appliance is too high. | Refer to "High temperature alarm" or "Door open alarm". | |
The door is left open. | Close the door. | |
The compressor operates continually. | Temperature is set incorrectly. | Refer to "Control panel" chapter. |
Many food products were put in at the same time. | Wait a few hours and then check the temperature again. | |
The room temperature is too high. | Refer to "Installation" chapter. | |
Food products placed in the appliance were too warm. | Allow food products to cool to room temperature before storing. | |
The door is not closed correctly. | Refer to "Closing the door" section. | |
The FastFreeze function is switched on. | Refer to "FastFreeze function" section. | |
The compressor does not start immediately after pressing the "FastFreeze", or after changing the temperature. | The compressor starts after a period of time. | This is normal, no error has occurred. |
Door is misaligned or interferes with ventilation grill. | The appliance is not levelled. | Refer to installation instructions. |
Door does not open easily. | You attempted to re-open the door immediately after closing. | Wait a few seconds between closing and re-opening of the door. |
The lamp does not work. | The lamp is in stand-by mode. | Close and open the door. |
The lamp is defective. | Contact the nearest Authorized Service Centre. | |
There is too much frost and ice. | The door is not closed correctly. | Refer to "Closing the door" section. |
The gasket is deformed or dirty. | Refer to "Closing the door" section. | |
Food products are not wrapped properly. | Wrap the food products better. | |
Temperature is set incorrectly. | Refer to "Control panel" chapter. | |
Appliance is fully loaded and is set to the lowest temperature. | Set a higher temperature. Refer to "Control panel" chapter. | |
Temperature set in the appliance is too low and the ambient temperature is too high. | Set a higher temperature. Refer to "Control panel" chapter. | |
Water flows on the rear plate of the refrigerator. | During the automatic defrosting process, frost melts on the rear plate. | This is correct. |
There is too much condensed water on the rear wall of the refrigerator. | Door was opened too frequently. | Open the door only when necessary. |
Door was not closed completely. | Make sure the door is closed completely. | |
Stored food was not wrapped. | Wrap food in suitable packaging before storing it in the appliance. | |
Water flows inside the refrigerator. | Food products prevent the water from flowing into the water collector. | Make sure that food products do not touch the rear plate. |
The water outlet is clogged. | Clean the water outlet. | |
Water flows on the floor. | The melting water outlet is not connected to the evaporative tray above the compressor. | Attach the melting water outlet to the evaporative tray. |
Temperature cannot be set. | The FastFreeze function is switched on. | Switch off FastFreeze function manually, or wait until the function deactivates automatically to set the temperature. Refer to "FastFreeze function" section. |
The temperature in the appliance is too low/too high. | The temperature is not set correctly. | Set a higher/lower temperature. |
The door is not closed correctly. | Refer to "Closing the door" section. | |
The food products' temperature is too high. | Let the food products temperature decrease to room temperature before storage. | |
Many food products are stored at the same time. | Store less food products at the same time. | |
The thickness of the frost is greater than 4-5 mm. | Defrost the appliance. | |
The door has been opened often. | Open the door only if necessary. | |
The FastFreeze function is switched on. | Refer to "FastFreeze function" section. | |
There is no cold air circulation in the appliance. | Make sure that there is cold air circulation in the appliance. Refer to "Hints and tips" chapter. | |
Temperature setting LEDs flash at the same time. | An error has occurred in measuring the temperature. | Contact the nearest Authorised Service Centre. The cooling system will continue to keep food products cold, but temperature adjustment will not be possible. |
If the advice does not lead to the desired result, call the nearest Authorized Service Centre.
The appliance is equipped with a longlife LED interior light.
Only service is allowed to replace the lighting device. Contact your Authorised Service Centre.
The technical information is situated in the rating plate on the internal side of the appliance and on the energy label.
The QR code on the EU and UK energy labels supplied with the appliance provide a web link to the information related to the performance of the appliance. For the energy label with the EU flag, it is also possible to find the information in the EU EPREL database using the link https://eprel.ec.europa.eu and the model name and product number that you find on the rating plate of the appliance. Keep the energy labels for reference together with the user manual and all other documents provided with this appliance.
Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damage that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.
Only a qualified person must install this appliance. |
Risk of fire and electric shock. |
When positioning the appliance, ensure the supply cord is not trapped or damaged. |
Do not use multi-plug adapters and extension cables. |
Risk of injury, burns, electric shock or fire. |
Risk of injury, burns, electric shock or fire.
The appliance contains flammable gas, isobutane (R600a), a natural gas with a high level of environmental compatibility. Be careful not to cause damage to the refrigerant circuit containing isobutane.
Risk of electric shock. |
Risk of injury or damage to the appliance. |
Risk of injury or suffocation.
zanussi.com\register
VISIT OUR WEBSITE TO:
Get usage advice, brochures, trouble shooter, service and repair information:
www.zanussi.com/support
Subject to change without notice.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Zanussi ZNLN14ES - Integrated Fridge Freezer Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the ZNLN14ES that isn't answered in the manual? Leave your question here.