Copyright 2006 InnoLux Tech. Corp. Ltd All Rights Reserved This manual may not, in whole or in part, be copied, Photocopied, reproduced, translated, or converted to any electronic or machine readable form without prior written permission of InnoLux Tech. Corp. Ltd. Acer G195W Service Manual...
Acer Acer –LCD-G195W Important Safety Notice Safety precautions This monitor is manufactured and tested on a ground principle that a user’s safety comes first. However, improper used or installation may cause damage to the monitor as well as to the user.
01 Product Specification General: G195W series LCD monitor is designed with a wide screen 19” WXGA+ TFT LCD panel, LVDS interface, analog RGB signal input and DVI-D signal input .It featured with embedded universal AC power supply. This monitor can support maximum resolution up to 1440x900@60Hz.
Page 5
Acer Acer –LCD-G195W Altitude 12,000 feet at 25°C (hold 3.5 hrs) Storage -30°C / humidity not controlled Low Temperature High temperature &low humidity +65°C/ 10% R.H. +25°C/ 50%R.H.(2hrs)-> -30°C/ No R.H.(12hrs).-> +41°C/ 90% Test Profile R.H.(12hrs)->+65°C/ 10% R.H.(12 Hrs)->+25°C/ 50% R.H.(2hr) Max.
Page 6
Acer Acer –LCD-G195W 2.3 Electrostatic Discharge Requirements The subject unit must withstand ±8KV for contact discharge and ±15KV for air discharge of Electrostatic Discharge and meet the standard of IEC61000-4-2(EN55024). (without discharge on VGA/DVI/HDMI pin) Item Condition Spec Remark Contact discharge : +/-4KV 150pF/330ohm.
Page 7
Acer Acer –LCD-G195W loading:0.04A~1.3A Vcc24V:23V~30V For power saving or DC off 24V loading: 0A Vcc5V: 4.85V~5.35V audio 5v:4.5V~5.5V audio 5v loading:0A DC Output Voltage Vcc5V/1.3A Vcc24V/1.2A audio 5V/1.0A DC output loading <50mS capability Hold-up time AC input: 100V~240V >10mS Overshoot <10%...
Page 8
Acer Acer –LCD-G195W 7.0mA (Typ.) 7.5mA (Max.) CCFL startup voltage ≧1700 Vrms (0˚C) Operating frequency 40~60KHz Protect delay time > 1 second Efficiency ≥70% (Using dummy load) Note: Other panels please refer to the reference panel specs. 3.2 Brightness output The test to verify specifications in this section shall be performed under the following standard conditions unless otherwise noted.
Page 9
Acer Acer –LCD-G195W Audio Signal(option) Specification Items TEST CONDITIONS Input impedance(Ω) Frequency response range(Hz) THD+N = 10%﹐@1KHz 1Vrms Signal to noise ratio(dB) THD+N = 10%﹐@1KHz 1Vrms Output power(W) 4. Input / Output Signal Specifications 4.1 Video signals Analog RGB signal: 0.7Vp-p...
Page 11
Acer Acer –LCD-G195W Temperature : 25 ± 5°C Warm-up time : 30 minutes minimum Checking display modes : All the specified modes 5.1 Panel general specifications 5.1.1 General specifications Supplier MT190AW02 V.0 Model name Display Area 408.24 ( H ) x255.15 ( V ) , 19W” diagonal Pixel Pitch 0.3(H) x 0.3(V)
Page 12
Acer Acer –LCD-G195W b. Show “source icon” at the same time, as searching that port c. Go into next port automatically, if search the port without signal d. Display it, if search the port with signal D. When the volume menu displays, press [►] to increase the volume.
Page 13
Acer Acer –LCD-G195W 0~100 V.Position 0~100 Focus 0~100 Clock 50 ○ Warm Default Cool Colour Temp 0~100 User Green 0~100 0~100 Blue Auto Config 10~120 OSD Timeout Volume ----- ----- 0~100 Full Default Wide Mode Aspect DDC/CI Input EMEA NO-EMEA...
Page 18
Acer Acer –LCD-G195W 7.1.2.1 Random Vibration Items Description Sweep Frequency 1~200Hz Amplitude 1.14 Grms Duration Time 30 minute each axis Direction 3 mutually perpendicular axes (x, y, z) RANDOM VIBRATION SPECTRUM BREAK POINTS PSD, G 2 /Hz Frequency (Hz) 0.0001 0.01...
Page 19
Acer Acer –LCD-G195W 9.1 S/N Label The approval marking is required by the countries of sales destination. 9.2 Carton label The approval marking is required by the c ountries of sales destination.
Page 22
SPEC NO. M T 1 9 0 AW 0 2 V. Y PAGE 4/23 A.General specification Item Specification Remark Display resolution (pixel) 1,440(H) X 900(V), WXGA+ resolution Active area (mm) 408.24(H) X 255.15(V) Screen size (inch) 19 inches diagonal Pixel pitch (mm) 0.2835(H) X 0.2835(V) Color configuration R, G, B vertical stripe...
Page 23
SPEC NO. M T 1 9 0 AW 0 2 V. Y PAGE 5/23 B. Electrical specifications 1.Pin assignment Connector FOXCONN GS23302-0311S-7F or mechanical interface equivalent connector. Pin No Symbol Description Frame Ground RXinO0- -LVDS differential data input, Chan 0-Odd RXinO0+ +LVDS differential data input, Chan 0-Odd RXinO1-...
Page 24
SPEC NO. M T 1 9 0 AW 0 2 V. Y PAGE 6/23 Top view of LVDS connector Rear view of LVDS connector...
Page 25
SPEC NO. M T 1 9 0 AW 0 2 V. Y PAGE 7/23 2. Absolute maximum ratings Values Unit Parameter Symbol Remark Typ. Min. Max. -0.3 Power voltage At 25°C -0.3 Input signal voltage At 25°C Operating temperature °C Note 1 Storage temperature °C...
Page 26
SPEC NO. M T 1 9 0 AW 0 2 V. Y PAGE 8/23 3. Electrical characteristics a. Typical operating conditions Item Symbol Min. Typ. Max. Unit Remark Input Voltage 0.15 Permissive Power Input Ripple Input Current Black 1000 Note 1 White Note 2 1000...
Page 27
SPEC NO. M T 1 9 0 AW 0 2 V. Y PAGE 9/23 Note 4 : test condition :‘ µ (1) V = 5 V, V rising time = 470 s ± 10% (2) Pattern: Mosaic pattern μ Ton=470 s ±...
Page 28
SPEC NO. M T 1 9 0 AW 0 2 V. Y PAGE 10/23 Note 6 : Power on sequence for LCD V Panel Power Supply V Interface Valid Interface Data Signals Backlight Power Supply Parameter Value Unit 1000...
Page 29
SPEC NO. M T 1 9 0 AW 0 2 V. Y PAGE 11/23 b. Display color vs. input data signals The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for the color;...
Page 30
SPEC NO. M T 1 9 0 AW 0 2 V. Y PAGE 12/23 c. Input signal timing Support Input Timing Table Item Description Min. Typ. Max. Unit Clock period 17.24 22.5 Dclk frequency 44.4 V total line number V_TOTAL H_TOTAL Data duration -...
Page 31
SPEC NO. M T 1 9 0 AW 0 2 V. Y PAGE 13/23 d. Display Position D(1, 1) D(2, 1) …… D(720, 1) …… D(1439, 1) D(1440, 1) D(1, 2) D(2, 2) …… D(720, 2) …… D(1439, 2) D(1440, 2) ……...
Page 32
SPEC NO. M T 1 9 0 AW 0 2 V. Y PAGE 14/23 Note 3: Test equipment: AS-114B Note 4: The voltage shown above should be applied to the lamp for more than 1 second after startup. Otherwise, the lamp may not be turned on normally. Note 5: Inverter should provide more than min.
Page 33
SPEC NO. M T 1 9 0 AW 0 2 V. Y PAGE 15/23 C. Optical specifications Specification Item Symbol Condition Unit Remark Min. Typ. Max. Response time θ ∘ Note 4 Tr+Tf θ 1000 ∘ Contrast ratio Note 3,5 Viewing angle CR≧10 CR≧10...
Page 34
SPEC NO. M T 1 9 0 AW 0 2 V. Y PAGE 16/23 "Black" "White" "White" 100% Note 5: Definition of contrast ratio: Contrast ratio is calculated by the following formula. Brightness on the "white" state Contrast ratio (CR)= Brightness on the "black"...
Page 35
SPEC NO. M T 1 9 0 AW 0 2 V. Y PAGE 17/23 Note 9: A’ B’ 127 gray level 127 gray level 0 gray level l / L x 100%= 2% max., L and L are brightness at location A and A’ A’...
Page 36
SPEC NO. M T 1 9 0 AW 0 2 V. Y PAGE 18/23 D. Reliability test items Test Item Test Condition Judgment Remark 60°C, 240Hrs High temperature storage Note 1 Note 2 -20°C, 240Hrs Low temperature storage Note 1 Note 2 High temperature &...
Page 37
SPEC NO. M T 1 9 0 AW 0 2 V. Y PAGE 19/23 E. Safety (1) Sharp Edge Requirements There will be no sharp edges or corners on the display assembly that could cause injury. (2) Materials a. Toxicity There will be no carcinogenic materials used anywhere in the display module.
Page 38
SPEC NO. M T 1 9 0 AW 0 2 V. Y PAGE 20/23 H. Label (1) Module Label 73 mm MT190AW02 AM1900006 MADE IN XXX ' - Z '- Z '- Z ' -Z ' -Z (a) Model Number: MT190AW02 (b) Version: V.Y (c) Serial ID I: Z Serial No...
Page 39
SPEC NO. M T 1 9 0 AW 0 2 V. Y PAGE 21/23 (2) Carton Label INNOLUX DISPLAY BOX ID : Model No. MT190AW02 AM1900006 Quantity : 7 PCS MFG Date: 20XX/XX/XX Made in XXX 100 mm (a) Model Number: MT190AW02 (b) Version: V.Y (c) Packing quantity: 7 pcs (d) Serial ID: Z...
Page 46
No Power & Power LED Off No power Check primary rectifier Check circuit if Check IC802, voltage short C804, T801, Check F801, P801, RT,801,D801 Check pin6 of IC802 CheckC810,D803,C807, voltage about 16V Check primary OVP, OLP and Check pin2 of IC802 voltage secondary feedback, OVP circuit about 3V...
Page 47
4.5 DC output voltage is unstable Unstable power Check Check sampling R822,R825,R826, Circuit R822,R825,R826, Check the C pin Check the R pin Change IC803 voltage of IC803 voltage of IC803 Check R832 Check pin7 of Check D803,C807,C810 if IC802 voltage short Change D803,C807,C810 Check pin3 of...
Page 48
Backlight can’t be turned on No raster? LED Green? Backlight can’t be turned on. Is there 5Vdc voltage Check power on pin2 of IC501? supply Is there high-level voltage on Check I/F board Is Ok R505? pin6 of IC501? R505 open Are connected rightly Connecting the CN501, CN502, CN503...
Assembly and Disassembly Use a screwdriver to unscrew the 4 S1: Disassemble the hinge cover. screws to release the stand. S4:put the dissemble monitor on the desk...
Page 59
Turn over the LCD monitor( screen facing down), Turn over the LCD monitor( screen facing up) then dissemble the back from the front bezel. Wedge your finger between the front bezel and the panel, And then pry the front bezel to disengage the locking mechanism.
Page 60
S10: Release the LVDS cable from the panel S8: Release the cable between and the main board. Release the aluminum foil the keypad and the main board. on the LVDS. S11: Release the aluminum foil from the panel. S9: Release the CCFL cable from the panel and the power board.
Page 61
S13、Dissemble the panel from the S12: Dissemble the chassis from the front bezel. front bezel. disengage the locking mechanism. NOTE: locking mechanism...
Page 62
S14、Release the keypad from the s15、 Release the cable。 front bezel. s16、 Use a screwdriver to unscrew the screws to release the main board and power board.
Page 63
s17、 Use a screwdriver to unscrew the s19、 release the power board and main board from screws to release the main board. the chassis. s18、 release the speaker cable from the power board.