28JW-74E SERVICE MANUAL SE0028JW74E00 Issued: 2 April 2003 GA-200 CHASSIS / SECAM SYSTEM COLOUR TELEVISION B/G, I L/L’, B/G, D/K MODEL 28JW-74E In the interests of user safety (required by safety regulations in some countries) the set should be re- stored to its original condition and only parts identi- cal to those specified should be used.
Page 2
28JW-74E SERVICE MANUAL UPDATE LOG SHEET Technical Report No. Application Cause / Solution Part No. Page No. Data /Serial No. Technical Bulletin No. Use this page to keep any special servicing information as Technical Report (Bulletin), Technical Information, etc. If only part number changes are required, just change part number directly the part number in the Parts Listing Section.
28JW-74E IMPORTANT SERVICING NOTES Only qualified service personnel are allowed to carry out maintenance and repair of this receiver. Servicing of High Voltage System and CRT It is important that the static charge is removed from the high voltage system when carrying out work on the receiver.
28JW-74E REMOTE CONTROL 1. Stand-by button (TV) Video 2. Power button (VCR) 3. 0 ~ 9 digit buttons 4. Flash back button Teletext 5. GREEN button 6. RED button 7. Volume DOWN button 8. MENU button Teletext 9. REVEAL button 10.
Page 7
28JW-74E • • • • • Use the channel up and down buttons to move between the options. • • • • • Use the volume control buttons to change the data. • • • • • To store the data, use the stand-by button on the remote control.
Page 8
28JW-74E The following geometry adjustments can be carried out. Detailed instructions on how to execute these are given on the following pages: Horizontal • Horizontal Shift Vertical • Vertical Amplitude • East West Width • Pin Phase • S Correction •...
Page 9
28JW-74E Upper Corner Correction Adjust the Upper Corner Correction so that the picture is centred. The effect of this adjustment is shown in figure 6. • When the volume up button is pressed, side pincushion changes from pincushion to barrel shape.
Page 10
28JW-74E Vertical Bow Adjust the Vertical Bow so that the picture is centred. The effect of this adjustment is shown in figure 11. • When the volume up button is pressed, the vertical bow changes to left. • When the volume down button is pressed, the vertical bow changes to right.
Page 11
5. If another NVM value has to be changed, use the channel down button to select the page or position and repeat as necessary. Note: DO NOT change any NVM data, unless you have been advised to do so by a Sharp representative. If data is incorrectly changed, serious damage may occur to the receiver. Contrast Adjustments Three types of contrast levels can be varied as listed below: •...
Page 12
28JW-74E DVCO Adjustment (NTSC) Carry out the DVCO Adjustment (NTSC) as shown below: 1. Receive a color pattern signal (NTSC 3.58). 2. While in the DVCO ADJUSTMENT (NTSC) menu, press the stand-by button. 3. The adjustment will be carried out automatically and stored.
28JW-74E LED FLASHING CODES This model is not provided with stereo led, so to let “flashing codes” for IC failures detection when the TV set does not work, we offer the next solution: • The detection of failure will be made with an external LED.
28JW-74E SCHEMATIC DIAGRAMS Description NOTE: SAFETY NOTE: 1. The unit of resistance « ohm »is omitted (K=1000 1. DISCONNECT THE AC PLUG FROM THE AC ohms. M= Megaohm). OUTLET BEFORE REPLACING PARTS. 2. All resistors are 1/8 watt. unless otherwise noted.
Page 37
28JW-74E Schematic Diagram of CRT Unit (F7269N4)
Page 38
28JW-74E Page 40 Schematic Diagram of Mother Board Unit (F7351N4A)
Page 39
28JW-74E Page 41 Schematic Diagram of Mother Board Unit (F7351N4A)
Page 40
28JW-74E Schematic Diagram of Mother Board Unit (F7351N4A)
Page 41
28JW-74E Schematic Diagram of Mother Board Unit (F7351N4A)
Page 42
28JW-74E Schematic Diagram of TVTextPRO Digital Module Unit (F7353N1)
Page 43
28JW-74E Schematic Diagram of TVTextPRO Digital Module Unit (F7353N1) 57 *1 Firmado Firmado Firmado digitalmente por digitalmente por digitalmente por Castillo, Fco. Josep Vila Sola ADOLFO Nombre de Nombre de FERNANDEZ reconocimiento reconocimiento Nombre de (DN): cn=Castillo, (DN): cn=Josep reconocimiento Fco.,...
Page 44
28JW-74E Schematic Diagram of Switch A/V Unit (FB515N0B)
28JW-74E TROUBLESHOOTING TABLES 7+( +25,=217$/ 67$*( 67$57 83 %87 7+( 3,&785( 25 6281' ,6 127 &255(&7 ± *Although the checking of these parts could be right, they may be partially damaged. So if the problem remains proceed to replace all parts.
Page 48
28JW-74E ',*,7$/ 02'8/( * XXJF74E and XXJW74E models don’t have a stereo led. Please refer to “LED FLASHING CODES” (Page 13). Test Point...
Page 49
28JW-74E 7+( 79 6(7 '2(6 127 67$57 83 *In the original situation (with the Digital Module assembled) this value is 1.8V.
Page 50
28JW-74E Note: Once the TV set has been repaired, have in mind to put the TV set in the default situation (undo short- circuits, specially the applied in Q1004).
28JW-74E ICs ADDITIONAL INFORMATION TDA9886TS (IC201) Features FEATURES • 5 V supply voltage • Gain controlled wide-band Vision Intermediate Frequency (VIF) amplifier, AC-coupled • Multistandard true synchronous demodulation with active carrier regeneration: very linear demodulation, • SIF-AGC for gain controlled SIF amplifier, single...
Page 52
28JW-74E TDA9886TS (IC201) Block Diagram handbook, full pagewidth...
Page 53
28JW-74E TDA9886TS (IC201) Pin Description SYMBOL DESCRIPTION TDA9886T TDA9885T TDA9885HN TDA9886TS TDA9885TS VIF1 VIF differential input 1 VIF2 VIF differential input 2 − − n.c. not connected output port 1; open-collector FMPLL FM-PLL for loop filter DEEM de-emphasis output for capacitor...
Page 56
28JW-74E TDA7480L (IC501) 10W OUTPUT POWER: = 8Ω/4Ω; THD = 10% HIGH EFFICIENCY NO HEATSINK SPLIT SUPPLY OVERVOLTAGE PROTECTION ST-BY AND MUTE FEATURES SHORT CIRCUIT PROTECTION PDIP20 (14+3+3) THERMAL OVERLOAD PROTECTION DESCRIPTION The TDA7480L is an audio class-D amplifier as-...
Page 57
28JW-74E TDA6111Q (IC850, IC851, IC852) Block Diagram supply voltage feedback input HIGH output handbook, full pagewidth MIRROR MIRROR FOLLOWERS cathode transient V bias output C par cathode inverting DC output input DIFFERENTIAL TDA6111Q STAGE non-inverting black current input measurement output...
Page 60
28JW-74E SDA9380 (IC6006) Pin Description Pin No. Name Type Description CLKI I/TTL Input for external line locked clock *) Reference oscillator output, Crystal Reference oscillator input, Crystal CLEXT I/TTL Switching between internal (L) and external clock (H) *) TEST I/TTL...
Page 61
28JW-74E SDA9380 (IC6006) Pin Description Pin No. Name Type Description VREFH Reference voltage VBLO Q/TTL Vertical blanking output VREFN Ground for VREFH VREFC Reference current input Dark current input for cut off and white level control VDD(A4) Analog supply Y/R 0...
Page 66
28JW-74E VSP9402A (IC6007) Pin Description pin 9402/32 9412/42 I/O 9402/32 9412/42 remark In 9402 A31 (and higher) and in VSP94xxA/B/C, this pin is shared by 656vin and blank...
28JW-74E PARTS LISTING 5() 1R 3$576 '(6&5,37,21 61 &2'( (; &2'( REPLACEMENT PARTS Replacement parts which have special safety characteristics are identified in this manual. Electrical components having such features are identified by in the Replacement Parts Listing. The use of a substitute replacement part which does not have the same safety characteristics as the factory recommended is not permitted.
28JW-74E SERVICING NOTES 1. How to rewrite the data in NVM. The NVM (Non Volatile Memory) is a read/write device aimed to keep the data even in the absence of power. The NVM contains IC configuration data, factory abjustable parametes (geometries, color temperature, etc.) and user settings (video, audio, programs, etc.).
Page 78
28JW-74E 2. Packing of the Set & Accessories Pack-ad SPAKX4077BMZZ Wrapper SPAKP2006BMZZ FRONT SPAKC5495BMZZ Carton Box Batteries UBATU0013TAZZ R/C Battery Cover GCOVHA010WJSA Remote Control RRMCG1073BMSA...