LG LND5100R Series - High Definition Network Camera Manual

Handling of the unit

Be careful not to spill water or other liquids on the unit. Be cautious not to get combustible or metallic material inside the body. If used with foreign matter inside, the camera is liable to fail or to get cause of fire or electric shock.

• Remove dust or dirt on the surface of the lens with a blower.
• Use a dry soft cloth to clean the body. If it is very dirty, use a cloth dampened with a small quantity of neutral detergent then wipe dry.
• Avoid the use of volatile solvents such as thinners, alcohol, benzene and insecticides.
  They may damage the surface finish and/ or impair the operation of the camera.

Operating and storage location

Avoid viewing a very bright object (such as light fittings) during an extended period. Avoid operating or storing the unit in the following locations.

• Extremely hot or cold places (operating temperature -10°C to 50°C, however, we recommend that the unit be used within a temperature range of 0°C to 45°C)
• Damp or dust place r Places exposed to rain
• Places subject to strong vibration
• Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.

Part Names and Functions

1. Dome Cover
2. IR LED
3. IR Sensor
4. Focus lock lever
5. Zoom lock lever
6. Azimuth adjuster

7. ETHERNET/PoE Port
   Connects to a PC or a network via a hub with a 10 BASE-T/100 BASE-TX cable attached RJ-45 connector.
   NOTE: Power over Ethernet (PoE) is a technology that integrates power into a standard LAN infrastructure. It enables power to be provided to the network device, such as a network camera, using the same cable as that used for network connection. It eliminates the need for power outlets at the device locations and enables easier application of uninterruptible power supplies (LPS).
8. Tilting lock screw
9. Pan adjuster
   Adjusts the pan position.
10. ALARM IN&OUT / ALARM IN&OUT RETURN
    Provides physical interface for sensor and Alarm/Relay.
11. AUDIO OUT (Line Level Output)
12. AUDIO IN (Line Level Input)
13. Power input terminal
    Connects to a DC 12 V power supply using proper cables. This camera must always be operated a DC 12 V. Certified/Listed Adaptor which comply with LPS.
14. Camera mounting bracket
    You can lock the camera mounting bracket by using the lock button.
15. Video Out connector
    Use this jack for checking the picture with portable monitor when install the camera.
16. RESET button
    Push the button more than 3 seconds, this would restore the factory default network related settings.
17. micro SD card slot
    Insert the micro SD card.

Connection

Precautions

• Be sure to switch off the unit before installation and connection.
• The installation should be made by qualified service personnel or system installers.
• Do not expose the power and connection cables to moisture, which may cause damage to the unit.

Connecting Network
You can control and monitor the system via network. With the remote control (monitoring), you can change the system configuration or monitor the image via network. After the installation, check the network settings for the remote control and monitoring work.
Connect the IP camera to your network using a standard RJ-45 network cable as shown below.

Connecting Power Source
Connect power, using one of the methods listed below:

To use the power adapter
Connect a DC 12 V power source to the power input terminal as shown below.
(recommended power adapter is DC 12 V/1.5 A or above)

To use the PoE (Power over Ethernet) device
Connect the PoE cable to the LAN port on the unit. You must use the "IEEE802.3af" standard PoE device.

NOTE:
If the camera doesn't work properly after connecting PoE device, please check if the PoE device supplies enough power.

Connecting Alarm Device
Alarm terminals are used to connect the alarm (relay) devices such as sensors, door switches, etc.

ALARM IN&OUT / ALARM IN&OUT RETURN
(Sensor Input / Relay Output)
Connect the sensor device and alarm (relay) device to the alarm terminal. Alarm signal is outputted at an event occurrence.

NOTE:
The PhotoMOS Relay is rated for 100 mA at 20 V DC or 100 mA at 28 V AC.

Connecting Microphone and Speaker Device
Optionally connect an active speaker and/or external microphone with a built-in amplifier.

NOTE:
Keep the microphone away from the speaker to avoid howling.

Using the micro SD card
You can record your surveillance environment with the micro SD card even if the network is disconnected condition.

To insert the micro SD card

1. Remove the Dome Cover.
2. Insert the micro SD card carefully as shown in the following illustrations. Make sure the micro SD card terminal position before insert the micro SD card. Push the back end of the micro SD card to fix it at the last step.
   

NOTES:

1. Do not use the power too much when you insert the micro SD card. The micro SD card may be damaged.
2. If you insert the micro SD card in the wrong position, the micro SD card may be damaged or it may cause the malfunction of the micro SD Card Slot.
3. Keep the terminal part of the micro SD card in clean. Be careful the terminal part of the micro SD card not to dusty.
4. As the micro SD card is consumable, the micro SD card end its days and may be not able to save data if you use it more than over certain times. In this case, replace micro SD card to buy a new one.

Remove the micro SD card

1. Press the back end of the micro SD card to release the lock condition.
   
2. Take the micro SD card out carefully from the camera. It may cause a malfunction of the micro SD card or the micro SD card slot if you use the power too much at lock status.

• If you install the micro SD card on the camera and remove with the micro SD card condition indicator lights on, you must unmount the micro SD card by using the [SD Card > Configuration > Disk Management > Unmount] menu. The micro SD card data is compromised or the camera may not operate normally, if you remove the card without use [Unmount] function.
  LG Electronics is not responsible for deleted data caused by user mishandling when you insert or remove the micro SD card.

Recommended the micro SD card specification

NOTE:
Speed of reading and writing more than 10 MB/Sec. (Class 6)

Installation

Mounting the camera
Follow the instructions below to install the camera with camera mounting bracket.

1. Use the installation guide template to check the mounting location. Face the front of the label toward the area of interest. Using the template as a guide, make a hole through the ceiling.
   
2. Install the camera mounting bracket to the ceiling.
   
3. Connect the cables to the cable jacks of the camera body.
   
4. Assemble the camera and mounting bracket after align the front part of the camera and mounting bracket. Connect the unit by following step and .
   

Camera Adjustment

1. Connect the portable monitor to the video jack using the test monitor cable.
   
2. Adjust the zoom and focus. Adjust the Pan/Tilt/Rotation position of the camera.
   

Note:
Disassemble the IR cover as illustrated in case of difficult occasion to adjust the zoom or focus lever.

Specification

Important Safety Instructions

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
    
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

Do not install this equipment in a confined space such as a bookcase or similar unit.

Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70.

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

To reduce a risk of fire or electric shock, do not expose this product to rain or moisture.

This installation shall be made by a qualified service person and shall conform to all local codes.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

The apparatus shall not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, shall be placed on the apparatus.
To disconnect power from mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible.

LG Electronics hereby declares that this/these product(s) is/are in compliance with the essential requirements and other relevant provisions of Directive 2004/108/ EC and 2011/65/EU.

Contact office for compliance of this product:
LG Electronics Inc.
EU Representative, Krijgsman
1,1186 DM Amstelveen, The
Netherlands