Table of Contents
Related Manuals for Toro Verticutter Reelmaster 5010 Series
Summary of Contents for Toro Verticutter Reelmaster 5010 Series
- Page 1 Form No. 3456-830 Rev A Verticutter Reelmaster ® 5010 Series Cutting Unit with 5in Reel Model No. 03618—Serial No. 408000000 and Up Model No. 03619—Serial No. 408000000 and Up *3456-830* Register at www.Toro.com. Original Instructions (EN)
- Page 2 Whenever you need service, genuine Toro parts, or Serial No. additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 This manual identifies potential hazards and has...
-
Page 3: Table Of Contents
Contents Safety Safety ............... 3 This machine has been designed in accordance with General Safety ........... 3 EN ISO 5395 and ANSI B71.4–2017. Cutting Unit Safety..........4 Blade Safety ............4 General Safety Safety and Instructional Decals ......4 Setup ................ 5 This product is capable of amputating hands and feet. -
Page 4: Cutting Unit Safety
• Use only accessories, attachments, and replacement parts approved by Toro. Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. -
Page 5: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Verticutter Inspect the verticutter. Transport roller assembly Install the transport rollers. Cotter pin O-ring Install the O-ring and the grease fitting. Straight grease fitting Install the shoulder bolt Shoulder bolt (RM5010–Hybrid only) -
Page 6: Installing The Transport Rollers
Installing the Transport Installing the O-ring and Rollers the Grease Fitting Parts needed for this procedure: Parts needed for this procedure: Transport roller assembly O-ring Cotter pin Straight grease fitting Procedure Procedure Secure a transport roller bracket to each side plate pin Install the grease fitting on the reel-motor side of the with a cotter pin (Figure... -
Page 7: Installing The Shoulder Bolt (Rm5010-Hybrid Only)
Installing the Shoulder Bolt (RM5010–Hybrid only) Parts needed for this procedure: Shoulder bolt Procedure For verticutters being mounted on a Reelmaster g028407 5010-H, replace the shoulder bolt on the reel-motor Figure 5 side-plate (Figure 7) with the new shoulder bolt; 1. -
Page 8: Installing The End-Weight Kit (Model 03618 Only)
Installing the End-Weight Adjusting the Verticutter Kit (Model 03618 only) No Parts Required Parts needed for this procedure: Procedure End-weight kit (sold separately) Refer to Adjusting the Verticutter (page Procedure Buy and install the end weight kit appropriate for the configuration of your machine (Figure •... -
Page 9: Product Overview
Product Overview Operation Specifications Training Period Before operating the verticutter reels, evaluate the Model Net weight performance of the reel at the desired setting. Operate 03618 With no end weight: in a clear, unused area to determine if the desired 49.4 kg (109 lb) results will be achieved. - Page 10 Adjusting the Rear Grass Shield Note: When operating in turf conditions where there is excessive debris or thatch, open the rear discharge shield to help allow the debris to discharge from the reel. Loosen the bolts on the pivot of the grass shield (Figure 10).
-
Page 11: Operating Tips
Operating Tips • Operate the traction unit at full throttle, full reel speed (setting 9) and at the desired traction speed. • The maximum recommended blade penetration depths are as follows: – Model 03618 is 3 mm (1/8 inch). – Model 03619 is 6 mm (1/4 inch). •... -
Page 12: Maintenance
Maintenance Lubricating the Verticutter Each verticutter has 5 grease fittings (Figure 13) that Using the Kickstand When must be lubricated weekly with No. 2 lithium grease. The lubrication points are the front roller (2), the rear Tipping the Cutting Unit roller (2), and the reel motor splines (1). -
Page 13: Removing The Verticutter Blades From The Shaft
Removing the Verticutter Important: The order of disassembly is extremely important. Do not invert the Blades from the Shaft verticutter reel blades when disassembling or reverse the order when assembling them. Secure the end of the verticutter shaft, which Note the index hole in each verticutter blade. has only one washer and nut, in a vise. -
Page 14: Installing The Verticutter Blades
Installing the Verticutter Blades Assemble a blade (Figure 16). Assemble a large spacer. Do not invert the reel blades when assembling them on the reel shaft. Note: If you invert the blades, the blades in use (rounded) will mix with the sharp ends of the previously unused blades, resulting in unsatisfactory cutting performance. -
Page 15: Optional Blade Spacing
Optional Blade Spacing 0.50-Inch Blade Spacing for Model 03618 To change the configuration of the verticutter from the standard 0.75-inch spacing to the 0.50-inch spacing requires an additional 34 spacers, Part No. 17-1580 and an additional 10 carbide blades, Part No. 106-6355, or an additional 10 regular blades and Part No. -
Page 16: Servicing The Roller
Refer to your parts catalog or Roller Rebuild Tool Kit (Part No. 115-0803) (Figure contact your authorized Toro distributor for assistance. 19) are available for servicing the roller. The Roller Rebuild Kit includes all the bearings, bearing nuts,... - Page 17 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 18 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Regulations.
- Page 19 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.
- Page 20 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact your Authorized Toro Service Center.