Health & Safety Code Section 25249.6 - Proposition 65 IMPORTANT Laser Pickup specifications and Laser characteristics THIS PIONEER APPARATUS CONTAINS For CD Wave length (typ) : 790 nm LASER OF CLASS 1. Operation output : 4 mW CW, Class 1...
• Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. 1.2 WHEN REPLACING CD MECHA UNIT It is necessary to remove the soldering on the short circuit point after connecting the flexible cable. Short circuit point X-HM20-K...
2. SPECIFICATIONS As part of our policy of continuous improvement, g USB PIONEER reserves the right to make design and specification changes for product improvement without USB host interface k Complies with USB 1.1 (Full prior notice. The performance specification figures Speed)/2.0 Mass Storage...
FL DISPLAY LCD201 ( IC 201) iPOD PCB VOLUME VR POWER ON ASSY (VOL201) DISPLAY PCB ASSY (X-HM20 ONLY) FUNCTION SCN802(4P) SCN801(6P) KEY BUTTON PLAY STOP DOWN OPEN/CLOSE USB CONNECTOR HP (JACK801) HEADPHONE USB PCB ASSY KEY-SWITCH PCB ASSY PCB ASSY X-HM20-K...
After a shutdown, to turn the unit back on, unplug the AC power cord then plug it back into the AC outlet. 6. SERVICE MODE There is no information to be shown in this chapter. X-HM20-K...
(1) Remove the top cabinet. (See procedure "[1] Top Cabinet".) Top cabinet iPOD PCB Assy (1) Disconnect the one flexible cable and one connectors. (J802, J803) (2) Remove the two screws. (3) Remove the iPOD PCB Assy. J802 J803 • Bottom view X-HM20-K...
Page 14
(9) Remove the front panel section. Volume knob Front panel section (10) Remove the two screws. HEADPHONE PCB Assy (11) Remove the 12 screws. KEY-SWITCH PCB Assy USB PCB Assy (12) Remove the DISPLAY, KEY-SWITCH, HEADPHONE and USB PCB Assemblies. DISPLAY PCB Assy X-HM20-K...
Page 15
(1) Remove the top cabinet. (See procedure "[1] Top Cabinet".) (1) Remove the five screws. • Rear view MAIN PCB Assy (2) Disconnect the one flexible cable and one connectors. (J1, J6) (3) Remove the RADIO PCB Assy. RADIO PCB Assy X-HM20-K...
Page 16
(2) Remove the one screw. • Rear view (3) Remove the three screws. POWER PCB Assy (4) Remove the two screws. MAIN PCB Assy (5) Disconnect the two connectors. (J9, J11) (6) Remove the POWER PCB Assy. POWER PCB Assy X-HM20-K...
Page 17
(1) Disconnect the two flexible cables and five MAIN PCB Assy connectors. (J1, J6, J9, J10, J11, J13, J19) (2) Remove the four screws. (3) Remove the MAIN PCB Assy. (4) Remove the three screws. (5) Remove the LOADER Assy. LOADER Assy X-HM20-K...
Page 18
• Bottom view Disc tray cover The Application Position of Adhesive X-HM20 ONLY Adhesive (No.1600B) GYL1007 Adhesive (No.1600B) GYL1007 Ferrite core Gasket iPOD PCB Assy RADIO PCB Assy X-HM20-K...
1. Press INPUT button to "Line in" function. 2. In "Line in" function, short press np button once then long press f(PLAY/PAUSE) button until the software version is displayed. software version display: X-HM20-K/-S → "CD-HM20R Vxxx", X-HM10-K/-S → "CD-HM10R Vxxx" X-HM20-K...
Screws adjacent to b mark on product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 9.1 PACKING SECTION X-HM20 only X-HM20-K...
Page 21
12 Speaker Packing Add See Contrast table (2) 13 Miramat Bag Unit 92L89134045001 14 Packing Case See Contrast table (2) (2) CONTRAST TABLE X-HM20-K/SYXJC8, X-HM20-S/SYXJC8, X-HM10-K/SYXJC8 and X-HM10-S/SYXJC8 are constructed the same except for the following: X-HM20-K X-HM20-S X-HM10-K X-HM10-S Mark...
9.2 EXTERIOR SECTION X-HM20-K, X-HM20-S only X-HM20-K...
Page 23
23 FL Holder 92L51500200101 24 iPod Spacer See Contrast table (2) 25 CD Mecha Holder 92L51501510101 (2) CONTRAST TABLE X-HM20-K/SYXJC8, X-HM20-S/SYXJC8, X-HM10-K/SYXJC8 and X-HM10-S/SYXJC8 are constructed the same except for the following: X-HM20-K X-HM20-S X-HM10-K X-HM10-S Mark Symbol and Description...
Page 25
GPIO0[11]/LCD_D7 TUNER_RESET/DAB_1V2_CTL EARPHONE_IN_DET GPIO0[10]/LCD_D6 GPIO0[9]/LCD_D5 TRAY_OUT GPIO0[8]/LCD_D4 LCD_D4 L for USB_3v3 of 5256 On STANDBY_KEY GPIO0[7]/LCD_D3 for Buck H Enable GPIO0[6]/LCD_D2 LCD_D2 LCD_D1 for Standby_LED_CTL GPIO0[5]/LCD_D1 GPIO0[4]/LCD_D0 LCD_D0 for analog_channel_SEL LCD_D0 LCD_D1 LCD_D2 2th Funciton for iPod_POW_CTL +3V3 IRDA X-HM20-K...
11. PCB CONNECTION DIAGRAM 11.1 MAIN and iPOD PCB ASSYS SIDE A CD MECHA CON702 UNIT (PICKUP) MAIN PCB ASSY Q851 Q850 U895 IC901 U900 IC13 IC800 U501 U551 Q601 X-HM20-K...
Page 51
SIDE A For further information for respective desti- nations, be sure to check with the sche- matic diagram. SIDE B P.C.Board Chip Part CON401 CON704 iPOD PCB ASSY J803 CON402 Q8 Q10 Q12 CON201 SCN201 X-HM20-K...
Page 52
SIDE B MAIN PCB ASSY iPOD PCB ASSY J803 X-HM20-K...
Page 53
SIDE B B ASSY IC795 IC902 Q420 X-HM20-K...
11.4 HEADPHONE and USB PCB ASSYS SIDE A SIDE A HEADPHONE PCB ASSY USB PCB ASSY SCN802 SCN801 SIDE B SIDE B HEADPHONE PCB ASSY USB PCB ASSY SCN802 SCN801 X-HM20-K...