Page 1 CD-ROM drive (MP-CDX1E). (The operating instructions guide is provided with each item packed.) INSTRUCTIONS Thank you for purchasing the JVC MP-XP7230GB/MP-XP5230GB Mobile mini note PC. Before Use Read and follow the instructions of this manual to use your Mobile mini note PC correctly.
Page 2: Safety Precautions
The correct function on a public analogue telephone line and a wireless LAN network is confirmed with the listed cautions. Should you have any problem on a specific network, we kindly ask you to inform your JVC Service Centre the nature of the problem and details of which service provider you are using.
Page 3: Some Do's And Don'ts On The Safe Use Of Equipment
CAUTIONS: ● This Mobile mini note PC is designed to be used with the JVC BN-LS12E/LL21E battery packs and, to recharge them or to supply power to the Mobile mini note PC from an AC outlet, use the provided AC Adapter and Power Cord.
Page 4: When Using The Wireless Lan
• This equipment with RLAN is intended to be used in Germany, UK, Austria and Switzerland. Outdoor use may be restricted to certain frequencies and/or may require a licence for operation. Hereby, JVC, declares that this MP-XP7230GB is in compliance with the essential requirements and other relevant provisions of Directive 1999 / 5 / EC.
Page 5: Cautions
Lithium-ion is vulnerable in colder temperatures. About Batteries DANGER! Do not attempt to take the batteries apart, or expose them to flame or excessive heat, as it may cause a fire or explosion. WARNING! Do not allow the battery or its terminals to come in contact with metals, as this can result in a short circuit and possibly start a fire.
Page 6: Checking Inventory
• External display • Modem cable (1.8-meters long) (MP-VGX1E) cable • Two Application CD-ROMs Lithium ion battery pack • BN-LL21E Large-capacity (only MP-XP7230GB) • BN-LS12E standard (only MP-XP5230GB) • Two stick caps (standard) • Protection cover (of battery terminal) • Instruction manual (this book) •...
Page 7: Jvc Software License Agreement
JVC original software accompanied with or pre-installed into the Product (“Software”). The right to use the Software is granted by Victor Company of Japan, Limited (“JVC”) to You only on the condition that You agree to the following Agreement. If You do not agree to the terms of the Agreement, you may not use the Software any more.
Page 8 8. Termination (1) Should You breach any provision of this Agreement, JVC may terminate this Agreement without giving any notice to You. In this event, JVC may claim against You any damages caused by Your breach. (2) Should this Agreement be terminated, You should immediately destroy the Software including any copy (including erasure from any memory in the Product) and any associated Materials, and then will not possess them.
Page 9: End-User License Agrement
G.726 Decoder ("Software") on your PC. The right to use the Software is granted by Victor Company of Japan, Limited ("JVC") to You only on the condition that You agree to the following Agreement. If You do not agree to the terms of the Agreement, you may not install the Software any more.
Page 10 Should You breach any provision of this Agreement, JVC may terminate this Agreement without giving any notice to You. In this event, JVC may claim against You any damages caused by Your breach. Should this Agreement be terminated, You should immediately destroy the Software stored in Your machine (including erasure from any memory in Your PC), and then will not possess such Software.
Page 11: Table Of Contents
Power-saving mode ..........77 SYSTEM APPLICATIONS Unknown partition on hard disk ......79 JVC ORIGINAL SOFTWARE ....... 24 Setup of JVC Original Software ...... 24 PC RECOVERY (REPEATED PC SETUP) DVC’s USB Drivers ......... 25 Setting Up Your PC Again ........82 CC Converter ..........
Page 12: Parts And Component Names
Wireless LAN antenna (model MP- XP7230GB only) Stick (On/Off) Key Lithium ion battery pack Left button BN-LS12E standard (MP-XP5230GB only) BN-LL21E Large-capacity (MP-XP7230GB only) Scroll button DC Input connector Right button Modem jack connectors Headphone LAN connector output Microphone input...
Page 13 Wireless LAN antenna (model MP-XP7230GB only) Wireless LAN antenna (model MP-XP7230GB only)
Page 15 SETTING UP...
Page 16: Setting Up
SETTING UP SETTING UP When you first use your Mobile PC, always plug the AC power cord into the DC Input connector. The built-in lithium-ion battery pack will be recharged during your PC setup. To avoid data loss due to power failure or any others cause, check the points for battery recharging in Page 18. 1.
Page 17 3. Open the display panel Buckle 1 Slightly pull up the buckle of the Note 2 Carefully open the display panel to the desired PC, and the display panel will be angle. You can open the display panel to 180 unlocked.
Page 18 SETTING UP 5. Make sure that the battery pack is fully charged To avoid an interruption of your operation due to power failure, check the battery voltage when you start to use your PC in the field. See "Checking the battery level" (see Page 76) to check the battery voltage level.
Page 19: Turn-On
HDD access lamp When the HDD is accessed Lights up green. Wireless LAN access lamp When wireless LAN is accessed Lights up orange. (model MP-XP7230GB only) SD access lamp When the SD card is accessed Lights up green. (model MP-XP5230GB only)
Page 20: Initial Setup Of Microsoft Windows
TURN-ON Initial Setup of Microsoft Windows When using your PC for first time, you must prepare to use Microsoft Windows. Once you have finished the initial Windows setup, you can use the software and various PC functions. Use the following procedure to initially set up Microsoft Windows. For pointing device and keyboard operations, see Pages 52 to 54.
Page 21 6. Enter the user name and click [Next]. The "Thank you!" screen will appear. Tips The name you have entered is shown on the "welcome" screen that appears when you turn the PC power switch on after initial Windows setup. To start up Microsoft Windows, click the user name shown on the screen.
Page 22: Turn-Off
TURN-ON Turn-Off Cautions • Always use this procedure to turn off the PC. Otherwise, your PC may fail. 1. Click [start]. The "start" menu will appear. 2. Click [Turn Off computer]. The "Turn off computer" screen will appear. 3. Click [Turn Off]. The PC will be turned off automatically, and (Stand By) lamp will go out.
Page 23 JVC ORIGINAL SOFTWARE AND SYSTEM APPLICATIONS...
Page 24: Jvc Original Software
JVC ORIGINAL SOFTWARE AND SYSTEM APPLICATIONS JVC ORIGINAL SOFTWARE To use the JVC original software, you must set it up in the "Original Software Setup Procedure" given below. You can setup the following software programs. Setup software • CC converter (See Page 27.) •...
Page 25: Dvc's Usb Drivers
• The driver to be set up depends on the DVC operation mode. • There is no operation problem although the "has not passed Windows Logo testing… " message appears. 1) If "The hardware: JVC DV Camera Storage" message appears:...
Page 26 1 Click [Continue Anyway]. 2 The driver will be installed automatically. 3 When "Completing the Found New Hardware Wizard" message appears, click [Finish]. 2) If "The hardware: JVC Web Camera" message appears: 1 Click [Continue Anyway]. 2 The driver will be installed automatically.
Page 27: Cc Converter
CC Converter This is a data-band expansion system JVC has developed for audio applications. It reproduces the timbre of the original sound from high-quality and compressed music data as well. The CC converter operates as a system filter so that it takes effect regardless of the playback application.
Page 28 JVC ORIGINAL SOFTWARE AND SYSTEM APPLICATIONS The following menu options are effective only when you have checked the "Enable" option. About the expansion effect modes One of the following three effect modes can be selected. Each has its own special characteristics as described below depending on the frequency band pattern which is to be expanded.
Page 29 ¡ About CC converter Shows the CC converter version and other information. Click [OK] to close the displayed subwindow. ¡ Exit Quits the CC converter. The CC converter status you have set at this point is held. If you wish to restart the CC converter, you can start up the program from the Start menu.
Page 30: Standard Application
TV screen or PC screen. Cautions • For communication using the USB connection, this software is supported by JVC’s digital video camera with the GR-DVP9EK and later model numbers. (It is also supported by old model numbers i.Link is used for communication.)
Page 31 ¡Pinnacle Studio 8 SE (only MP-XP7230GB) The video editing software for the broadband age. This software makes it possible to capture moving pictures or still pictures from a digital video camera or digital camera, add various video effects and output them to a digital video camera or create movies in a variety of formats.
Page 32: To Set Up The Standard Applications Again
JVC ORIGINAL SOFTWARE AND SYSTEM APPLICATIONS To Set Up the Standard Applications Again You can set up the standard applications using the Application CD-ROM. (The optional CD- ROM drive is required.) If you have erroneously deleted any of the standard applications, you can reinstall it from the Application CD-ROM.
Page 33: Navigate In The Internet World
NAVIGATE IN THE INTERNET WORLD!
Page 34: To Connect To The Internet
NAVIGATE IN THE INTERNET WORLD! TO CONNECT TO THE INTERNET You must contract with an Internet service provider. Also, you need to have a telephone line to be connected to the service provider. Contracting with the Internet Service Provider An Internet service provider (an enterprise or an organization that provides the Internet connection and related services) is generally called a "provider."...
Page 35: Connection Of Telephone Line And Modem Setup
Connection of Telephone Line and Modem Setup Your PC has a built-in modem and a cable attached to it. You can enjoy the Internet and e-mail services by simply connecting your PC to the telephone line. 1. Plug the attached modem cable into the Modem jack of your PC until it clicks. Insert the cable connector into the jack in the correct direction.
Page 36 NAVIGATE IN THE INTERNET WORLD! 3. Seting up the modem 1 Click [start] and [Control Panel] in this order. 2 Click [Printers and Other Hardware]. 3 Click [Phone and Modem Options]. 4 When the "Location Information" screen appears, enter a city code in the "area code" field.
Page 37: The Internet Connection Setup
The Internet Connection Setup Use the following procedure to connect your PC to the Internet network. This setup example uses the built-in modem of your PC and Microsoft’s Internet Explorer (IE) for the Internet connection. If you have already contracted with a provider, you can manually set up the Internet connection using the following procedure.
Page 38 NAVIGATE IN THE INTERNET WORLD! 3. Click [Connect to the Internet] option, and click [Next]. The "Getting Ready" screen will appear. 4. Click [Set up my connection manually] option, and click [Next]. The "Internet Connection" screen will appear. 5. Click [Connect using a dial-up modem] option, and click [Next]. The "Connection Name"...
Page 39 7. Enter the phone number, and click [Next]. The "Internet Account Information" screen will appear. 8. Enter the User name and Password (and enter the password again for confirmation), and click [Next]. The "Completing the New Connection Wizard" screen will appear. 9.
Page 40 NAVIGATE IN THE INTERNET WORLD! Tips If you need to set up the DNS server address, follow steps 10 to 20. You may need to set up DNS server addresses (the primary and secondary DNS addresses) for some providers. If the DNS server addresses are stated on the documents sent from your provider, you need to set them up.
Page 41 15. Click [Networking]. 16. Click [Internet Protocol (TCP/IP)] and click [Properties]. The "Internet Protocol (TCP/IP) Properties" screen will appear. 17. Click [Obtain an IP address automatically], click [Use the following DNS server addresses], and enter the DNS server address printed on the document sent from the provider.
Page 42: Connecting To The Internet
NAVIGATE IN THE INTERNET WORLD! Connecting to the Internet After you have completed the "The Internet Connection Setup" procedure (pages 37 to 41), you can connect to the Internet. Use the following procedure. 1. Click [start] and click [Internet] at the upper left part of the Menu. The Internet Explorer will start up and the "Dial-up Connection"...
Page 43: Disconnection From The Internet
Disconnection from the Internet When you are connected to the Internet, the use of the telephone line and the access to the provider are charged. Disconnect your PC from the Internet in one of the following ways when you are finished using the Internet.
Page 44: Accessing A Web Page
NAVIGATE IN THE INTERNET WORLD! Accessing a Web Page There is a large number of Web sites available. You can access a Web site using Microsoft’s Internet Explorer in your PC. The following shows three typical ways you can use to access a Web site.
Page 45: E-Mailing
E-MAILING You need to set up a mailing software to send and receive E-mails. Setting up E-Mail Software Set up the E-mail transmission using the Outlook Express installed on your PC. Tips It is convenient for E-mail setup if you have the document sent from the provider to hand. 1.
Page 46 NAVIGATE IN THE INTERNET WORLD! 3. Enter your E-mail address in the "E-mail address" field, and click [Next]. The "E-mail Server Name" screen will appear. 4. Enter the "Incoming mail server" and "Outgoing mail server", and click [Next]. Usually select "POP3" as the "My incoming mail server is a server."...
Page 47 5. Enter the "Account name" and "Password," and click [Next]. The "Congratulations" screen will appear. 6. Click [Finish]. The "Congratulations" screen will close, and Outlook Express will start up. The setup for the E-mail software is complete. 7. To quit Outlook Express, click [x] at the upper right corner of the screen.
Page 48: Sending And Receiving E-Mails
NAVIGATE IN THE INTERNET WORLD! Sending and Receiving E-mails You can create and send E-mail messages, and receive and read E-mail from others. You can learn procedures to enjoy E-mailing. Use Outlook Express installed on your PC for E-mail transmission. Transmission Connect to the provider.
Page 49 3. Create a message. Enter the E-mail address Enter the message title Enter the message text here Destination: Enter the receiver's E-mail address. (Enter your E-mail address first to test E-mail transmission.) Title: Enter the message title. 4. Click [Send] at the left upper end of the screen to send the created message. The "Dial-up Connection"...
Page 50 NAVIGATE IN THE INTERNET WORLD! 7. To check the received messages, click [Inbox] on the screen. The received E-mail messages will be displayed. 8. To quit Outlook Express, click [x] at the upper right corner of the screen. Caution • Disconnect your PC from the Internet after you have transmitted E-mail and finished accessing a Web site.
Page 51: Hardware
HARDWARE...
Page 52: Using The Pointing Device
HARDWARE Using the Pointing Device The pointing devices allow you to move the mouse pointer on the screen. You can move the cursor using the centre stick and three buttons in the similar way as the mouse. Mouse pointer Left button Scroll button Stick Right button...
Page 53 • Double-click Press the mouse left button twice in succession and release it immediately. • Drag Use this operation to move an icon or a file. To do so, select an icon or a file, hold down the mouse left button and move it to the desired position, and release the mouse button. Notes The pointing devices have initially been set for the "right-handed person"...
Page 54: Using Hot Keys
HARDWARE Using Hot keys You can use the coloured hot keys of the PC keyboard. Hold down the Fn key and press one of the Hot keys to execute its command. List of hot keys Reduces the screen brightness level. Use this command to reduce the brightness level if the screen is too bright.
Page 55: If A Key Top Has Come Off
If a key top has come off If a key top has come off from the keyboard, put it back in place by following the procedure below. ¡ How to attach the Enter key, left Shift key or Space key top 1 Take out the disengaged wire rod, and snag it onto the two projections as shown in the figure below.
Page 56: Increasing The (Optional) Memory Capacity
Product Specifications on Page 102. You can reduce the application startup time and increase the data process speed by adding an optional memory board. Consult the JVC PC Technical Support Centre listed at the end of this manual for memory expansion.
Page 57: Adding Or Removing A Memory Board
4. Add or remove a memory board. Cautions The MP-XP7230GB PC already has 128M-byte memory in its memory slot. You need to replace it with a 256M-byte memory board to expand the PC memory capacity to the maximum 384M bytes. To do so, remove the 128M-byte memory board from the slot. See Procedure...
Page 58 HARDWARE 1) Mounting a memory board 1 Check the correct mounting direction of memory board (by observing the cut area). 2 Slant the memory board and insert it into its socket. 3 Push the memory board until it is locked, but do not apply excessive force to it. Cautions If it is difficult to lock the memory board, make sure that the board has been inserted securely.
Page 59: Checking The Additional Memory Board
Checking the Additional Memory Board Use the following procedure to check the memory board installation. 1. Turn on your PC and start Windows. 2. Click [start] and select [Control Panel]. 3. Click the [Performance and Maintenance] icon. 4. Click the [System] icon. The "System Properties"...
Page 60: Using The Sd Memory Card Slot
HARDWARE Using the SD Memory Card Slot Your PC has an SD memory card slot. An SD memory card or multimedia card can be used. When you use an SD memory card, remove the dummy card from the SD memory card slot. 1.
Page 61: Using An External Monitor
Using an External Monitor To attach an external monitor to your PC, use the MP-VGX1E external display cable. Connecting an external monitor When you connect an external monitor to your PC, it looks like an ordinary desktop PC. You can use the monitor by just connecting it with the MP-VGX1E cable. You can display images on the external monitor for other people and you can watch them on the LCD panel of your PC.
Page 62 * How to enable and disable the expansion display with an LCD resolution of 800 x 600 1) Press the Alt + F2 keys when the system starts up (when the JVC logo is displayed). 2) The “Award BIOS Setup Utility” screen will appear. Select [Advanced] using the → cursor key.
Page 63: Connecting To A Network
Connecting to a network With the network function, you can connect to a network at your office or home to transfer data between PCs and access the Internet from multiple PCs. For setting for intranet connection, consult a system administrator at your company. Connection to a network requires the following items.
Page 64 HARDWARE 4 Double-click [Local Area Connection]. The “Local Area Connection Status” screen will appear. 5 Click the [Properties] button. The “Local Area Connection Properties” screen will appear. 6 On the [General] tab, double-click [Internet Protocol (TCP/IP)]. The “Properties of Internet Protocol (TCP/IP)” screen will appear. 7 Enter appropriate values in the [Use the following IP address] and [Use the following DNS server addresses] fields.
Page 65 8 Click the [OK] button. A message prompting you to restart the computer will appear. 9 Click the [OK] button to make the change take effect. 0 Restart the computer. ¡Checking the MAC address Use the following procedure to check the MAC address of the internal LAN card. Important To check the MAC address, you have to set a LAN (local area) connection in the [Network connection] screen.
Page 66 HARDWARE 5 Double-click [Local Area Connection]. The “Local Area Connection Status” screen will appear. 6 Click the [Support] tab and the [Details] button. The “Network Connection Details” screen will appear. 7 The MAC address is displayed as the “Physical Address” on the list.
Page 67: General Description Of Wireless Lan
Network connections using a wireless LAN (MP-XP7230GB only) The model MP-XP7230GB PC comes with wireless LAN functions. (The MP-XP5230GB series does not come with these functions, and the details provided in “Network connections using a wireless LAN” do not apply.) You can connect to a LAN system from any location within the wireless communication area to access the Internal LAN or send and receive mail.
Page 68: Suggestions For Using The Wireless Lan
LAN is possible, open the display, and point its reverse side (the side with JVC logo) at the access point. Do not place any obstacles such as books or thick stacks of paper between the PC and access point.
Page 69 1 Start up the PC. 2 Set the IP address to be used by the wireless LAN. 1 Click [Start], and select [Show all connections] from [Connect To] on the start menu. 2 Select [Wireless Network Connection] on the [Network Connections] screen, and select [Properties] on the [File menu].
Page 70 HARDWARE 3 Select [Internet Protocol (TCP/IP)] on the [General] screen of [Wireless Network Connection Properties]. 4 The [Internet Protocol (TCP/IP) Properties] screen appears. 5 Use the following example as a reference, and proceed with the settings depending on how the wireless LAN is to be used.
Page 71 For making the wireless network connection using a public wireless LAN service : With a public wireless LAN service, it is customary for the DHCP server function that automatically allocates the IP address to be enabled. On the “Internet Protocol (TCP/IP) Properties”...
Page 72 HARDWARE When the wireless LAN status icon is clicked on the task tray, the main menu of the wireless LAN setting utility is opened, enabling the wireless LAN status to be checked or set. The color of the wireless LAN status icon indicates the connection status and signal strength status.
Page 73 2 Settings Perform the wireless LAN communication settings. This utility can retain multiple sets of setting information, and these sets can be selected for use. The settings are each managed by a [Profile]. When new settings are to be added, input the profile name of your choice, and then proceed with the settings. [SSID] Perform the ESS-ID setting for the network name.
Page 74 HARDWARE 3 Encryption Perform the encryption (WEP security) settings for communication. The WEP function encrypts key words and scrambles them in the transmission data. A network using a high level of security can be configured when it is activated. While the function is activated, the same WEP keys must be used by all the computers in the group.
Page 75: How To Shut Down The Wireless Lan Functions
4 About The software version information and MAC address of the wireless LAN mode are displayed. [Network Driver] The network driver version information is displayed. [Configuration Utility] The configuration utility version information is displayed. [NIC Firmware] The version information and MAC address of the wireless LAN module’s firmware are displayed.
Page 76: Checking The Battery Level
HARDWARE Checking the battery level On the “Power Option Properties” screen, click the [Power Meter] tab. The current total battery level is displayed. Use the following procedure. 1. Click the [start] button and [Control Panel]. 2. Click the [Performance and Maintenance] icon. 3.
Page 77: Power-Saving Mode
Power-saving mode In compliance with the operation regulations of the International Energy Star Program, this unit enters the power-saving mode when no operation is performed for a certain period. On the [Power Schemes] tab in the “Power Option Properties” screen (page 76), you can specify the time that must expire before the unit enters the power-saving mode.
Page 78 HARDWARE • System in standby status The built-in battery discharges whilst the PC is in system standby status. As a result, any unsaved data may be lost or the system may not start up. Be sure to turn off the PC when it is not used for a long time.
Page 79: Unknown Partition On Hard Disk
Unknown partition on hard disk IMPORTANT!! This PC reserves the image data required for recovery as a “recovery area” in the hard disk. If you accidentally delete a partition of the recovery area, you cannot recover it. The important points to keep in mind are: •...
Page 81: Pc Recovery (Repeated Pc Setup)
PC RECOVERY (REPEATED PC SETUP)
Page 82: Setting Up Your Pc Again
PC RECOVERY (REPEATED PC SETUP) Setting Up Your PC Again 1. What is the Recovery? When you return your PC to the original state during shipment, it is called "PC recovery." You can recover your PC in one of the following two ways. (1) Initialize the hard disk and restore all files.
Page 83: System Recovery Procedure
System Recovery Procedure 1. Hold down the Alt and F8 keys and press the Power button to start up your PC. When message "Do you wish to continue? (Y/N)" appears, respond with Y. Tips • If you respond with N, the recovery is canceled. The PC will restart and the Windows OS will start up.
Page 84 COMPUTER WIEDERHERSTELLUNG (RECOVERY) 5. After the system recovery has been completed, the message "Turn Power switch off and restart the PC." appears. Restart your PC. Your PC has been returned to the original state before shipment. 6. Set up the Windows OS by following the "Initial Setup of Microsoft Windows" procedure on Page 20.
Page 85 TROUBLESHOOTING...
Page 86: Troubleshooting Q&A
Q&A section. If the Q&A does not help you Contact us. If you cannot remove the trouble successfully, contact the JVC PC Technical Support Centre. See the back cover for the phone number. Power The power does not turn on.
Page 87: Startup And Operation Of Windows
Startup and Operation of Windows The screen has hung. Use the following procedure to forcibly exit the applications running on your PC. Important When applications are forcibly terminated through this procedure, any unsaved unsaved data will be lost. Terminating an application forcibly 1.
Page 88 Use the following procedure to start up your PC in the safe mode. 1. Turn on the PC. 2. As soon as the JVC logo appears, hold down the F8 key. Tips If the F8 key is pressed too late, Windows tries to make a normal startup.
Page 89: Display
Display The PC is turned on but nothing appears on the screen. If the screen blacks out during operation, check the following. ¡ When the (Stand By) lamp is lit. • Move the stick or press any key on the keyboard to check if the power-saving function is working.
Page 90: Using The Internet
TROUBLESHOOTING Using the Internet I cannot dial up. Check the connection. ¡ Check that the modem cable is connected. If you see the “There was no dial tone.” message, check the connection between the unit and the telephone line connector on the wall. Insert the modem fully until it is locked. ¡...
Page 91 The PC dials but connection is not established. Check the dialing setting. ¡ Check that the dialing type (tone or pulse) is correctly set for your telephone line. For checking and configuration procedures, see “3. Setting up the modem” on page 36. ¡...
Page 92 TROUBLESHOOTING The PC makes a connection operation but connection is not established. Check the following. ¡ Check the user name and password. Refer to the material sent from your ISP for correct user name and password. ¡ The internal modem dials but negotiation is not made. The access point may have a problem.
Page 93: Wireless Lan
Wireless LAN (MP-XP7230GB only) I can’t communicate. Check the following. ¡ Is the device serving as the other end of the communication the kind of device which can communicate with the PC? A number of communication systems can be used with the wireless LAN, but unless the same system is used at both ends, communication will not be possible.
Page 94: Battery
TROUBLESHOOTING How can I check the MAC address? Proceed as follows to check the MAC address of the PC’s wireless LAN. * In order to check the MAC address, the wireless network connection must first be set using [Network Connections]. 1.
Page 95: Sd Memory Cards
SD memory cards The “Not formatted” or “Not initialized” error message appears when I insert an SD card, CF card or other memory card with a memory capacity exceeding 32MB into a digital camera or other device even though the card has been formatted, and I cannot use the card.
Page 96: Miscellaneous
TROUBLESHOOTING Miscellaneous The PC is hot. The PC may become warm when used for a long time, but this is not a failure. Do not block the vents in the bottom or sides through which internal heat is removed. The PC makes no sound. Check the following ¡Check if the speaker is muted.
Page 97 • To bring up the BIOS menu, turn on the PC and press the Alt and F2 keys while the JVC logo screen is shown. Do not change the BIOS setting unless you have adequate knowledge of computers. A wrong setting can make your PC unable to start up again or, worse, damage it.
Page 98 FRANGE & ANTWORTEN...
Page 99: Appendix
APPENDIX...
Page 100: List Of Support Centres
APPENDIX List of Support Centres 1. ImageMixer with VCD 1.1 VJ http://www.imagemixer.com 2. Norton AntiVirus 2003 http://www.symantec.com/region/reg-eu/techsupp/index.html 3. RealPlayer 8 Basic http://www.service.real.com 4. Pinnacle Studio 8 SE http://www.pinnaclesys.com...
Page 101: Trademark Notice
Trademark notice 1. i.LINK refers to IEEE1394-1995 and their expanded specifications. i.LINK and the i.LINK logo are trademarks of Sony Corporation, devised to make people more familiar with IEEE 1394. 2. Microsoft, Windows, Windows Media are trademarks or registered trademarks of Microsoft Corporation in the U.S.
Page 102: Specification
(auto-change) Interfaces External monitor outputs Modem jack (RJ-11) x 1 Wireless LAN (in accordance to IEEE 802.11b) x 1 (MP-XP7230GB only) USB(2.0) x 2 iLINK (IEEE1394) 4-pin S400 x 1 LAN connector (10/100BASE-TX) x 1 MIC IN (mini-jack mono) x 1...
Page 103: Wireless Lan Specifications
Wireless LAN specifications (MP-XP7230GB only) Wireless frequency band 2412 to 2472 MHz (all 13 channels) Modulation system DSS (Direct Spread Spectrum system) CCK (communication speed: 5.5 Mbps, 11 Mbps) DQPSK (communication speed: 2 Mbps) DBPSK (communication speed: 1 Mbps) Spread spectrum system...
Page 104: Options (Separately Available)
APPENDIX Options (separately available) Option name Model CD-ROM drive *1 MP-CDX1E Standard lithium ion battery pack *2 BN-LS12E Large-capacity lithium ion battery pack *3 BN-LL21E Battery charger *4 MP-BCX1E AC adapter *2 MP-ACX1GB External display cable MP-VGX1E Connected with a PC card and powered from the Mobile mini note PC. Maximum read speed is 16x.
Page 105 VICTOR COMPANY OF JAPAN, LIMITED 0197 · This equipment with RLAN is intended to be used in Germany, UK, Austria and Switzerland. Outdoor use may be restricted to certain frequencies and/or may require a licence for operation. · The built-in V.90 modem is installed for use on official analog telephone lines in Germany, UK, Austria, France and Switzerland.
Page 106 How you can use the built-in wireless LAN even more easily You can reduce the wireless LAN connection time by using the accessory utility. The Instructions of this PC are written on the assumption that this accessory utility will be used.
Page 107 Supplementary instructions for using internal wireless LAN If the wireless network connection has been disabled, the wireless LAN status icon the wireless network icon may not appear on the taskbar. The wireless LAN ON/OFF hot keys ( Fn + F9 ) will not work, either. When the wireless LAN is to be used in a situation like this, the wireless network connection must be enabled.
Page 108 USB Port Replicator MP-PRX INSTRUCTIONS Thank you for purchasing the JVC MP-PRX 1GB USB Port Replicator. Before Use Read and follow the instructions of this manual to use your USB Port Replicator. Always read the "Safety Instructions". Keep this manual for further reference.
Page 109 Dear Customer, Thank you for purchasing the JVC USB Port Replicator. This unit is to be used with JVC AC Adapter AA-E5025GB. To avoid problems and obtain the best results, please read this instruction booklet carefully before use. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
Page 110 Introduction This USB Port Replicator is a unique expansion unit specially designed to comple- ment the Notebook Computer and make it equivalent in many ways to a desktop PC. It provides some of the connection functions found on a desktop system. The USB Port Replicator allows you to add multiple high–performance USB 2.0 pe- ripheral devices to your PC.
Page 111 Package Contents USB Port Replicator AA-E5025GB AC Power Adapter USB Cable (1.8 meters long) Software CD-ROM Instruction Manual (this booklet)
Page 112 Hardware Installation LED Status Indicators Color Descriptions POWER Indicates that the power is on. 2 PORT HUB Green Indicates that both USB 2.0 ports are now ready and active. LAN (10/100) Green Indicates a data transfer rate of up to 100 Mbps. LAN (LINK) Green Indicates that an external device is connected to...
Page 113 Software CD-ROM. See the ‘Software Installation’ section for details on how to install the software. • In the case of the Mobile mini note PC MP-XP7230GB, the drivers for the USB Port Replicator have already been installed and the port replicator is ready to be used.
Page 114 Other I/O Ports Figure 3: Other I/O ports USB 2.0 Ports KEYBOARD Port MOUSE Port SERIAL Port (RS-232C) PARALLEL Port DATA LINK Port LAN Port USB 2.0 Ports Before connecting a USB 2.0 device to one of the USB 2.0 ports, refer to the Software Installation section of this Instruction Manual.
Page 115 Software Installation STEP 1 Connect the CD-ROM drive to the Mobile mini note PC and turn it on. Insert the Software CD-ROM. Supply power to USB Port Replicator using AC power adapter. Connect the Mobile mini note PC and the USB Port Replicator using the High-Speed Cable (USB cable) included with this port replicator.
Page 116 The wizard has finished installing the software. Click Finish to continue. STEP 3 The Mobile mini note PC finds the USB Bridge Cable (USB device) of the USB Port Replicator. This wizard helps you install the device driver. Select “Install the software automatically [Recommended]”. Click Next to continue.
Page 117 The wizard has finished installing the software. Click Finish to continue. STEP 4 Next the PC-Linq Software is installed to enable the data link connection between the Mobile mini note PC and other external PC via the USB file transfer data link port (DATA LINK port).
Page 118 Click Next to continue. Setup will add the program icon to the Program Folder. You may type a new folder name or select the default folder name. Click Next to continue. The PC-Linq icon will appear on the desktop. • Support Center PC-Linq software and driver http://www.goodway.com.tw/shop/online_service.asp...
Page 119 STEP 5 The Mobile mini note PC finds the Prolific USB-to-Serial Comm Port of the USB Port Replicator. This wizard helps you install the device driver. Select “Install the software automatically [Recommended]”. Click Next to continue. The wizard has finished installing the software. Click Finish to continue.
Page 120 STEP 6 Installation Verification...
Page 121 Appendix: Installing the PC-Linq Software and Driver in an External PC If you connect an external PC to the Mobile mini note PC via the DATA LINK port of the USB Port Replicator, you must install the PC-Linq software and driver on the external PC as well as instructed below.
Page 122 The wizard has finished installing the software. Click Finish to continue. STEP 4A The PC-Linq Software is now installed. The “Welcome to the Install Shield Wizard for PC-Linq” dialog window appears. Click Next to continue.
Page 123 Click Next to continue. Setup will add the program icon to the Program Folder. You may type a new folder name or select the default folder name. Click Next to continue. The PC-Linq icon will appear on the desktop of the external PC. •...
Page 124 Specifications Computer Port TO PC port (Upstream port) Type B receptacle I/O Ports 2 USB 2.0 ports Type A receptacles PS/2 KEYBOARD port Mini Din 6 pin PS/2 MOUSE port Mini Din 6 pin DATA LINK port Type B receptacle SERIAL port DB 9 pin male PARALLEL port...
Page 125 VICTOR COMPANY OF JAPAN, LIMITED Printed in Taiwan 0203KHY IDASS 2003 VICTOR COMPANY OF JAPAN, LIMITED...
Page 126 Setting Up of USB Port Replicator (MP-PRX1GB) Installing the device driver Note ● Log on to the computer using user with administrator privilege to install. ● If the setting for "Driver Signing Options" is set to "Block", then the device driver cannot be installed.
Page 127 This file has been downloaded from: www.UsersManualGuide.com User Manual and User Guide for many equipments like mobile phones, photo cameras, monther board, monitors, software, tv, dvd, and othes.. Manual users, user manuals, user guide manual, owners manual, instruction manual, manual owner, manual owner's, manual guide, manual operation, operating manual, user's manual, operating instructions, manual operators, manual operator, manual product, documentation manual, user maintenance, brochure, user reference, pdf manual Downloaded from:...

This manual is also suitable for:

Mp-xp5230gb Mp-xp7250de

JVC MP-XP7230GB Manual

Quick Links

Related Manuals for JVC MP-XP7230GB

Summary of Contents for JVC MP-XP7230GB

This manual is also suitable for:

Table of Contents