hit counter script
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Wireless Access Point
  5. 1130AG - Aironet - Wireless Access Point
  6. Hardware installation manual

Cisco Aironet 1130AG Series Hardware Installation Manual page 65

Hide thumbs Also See for Aironet 1130AG Series:
Table of Contents

Advertisement

Cisco Aironet 1130AG Series Access Point
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
3-8
3-8
   
Chapter 3 3
Chapter
Troubleshooting
Troubleshoo
Caution
Caution
Hardware Installation Guide
ting Autonomous
Autonomous Access
Access Points
Points
• •
%CDP_PD-2-POWER_LOW: All radios disabled- LOW_POWER_CLASSIC_INJECTOR_
%CDP_PD-2-POWER_LOW: All radios disabled- LOW_POWER_CLASSIC_INJECTOR_
CONFIGURED_ON_ANOTHER_PORT <  plat
CONFIGURED_ON_ANOTHER_PORT <
indicates the access point is in low power mode with all radios disabled and has detected a CDP
indicates the access point is in low power mode with all radios disabled and has detected a CDP
device that is unable to supply sufficient power to the access point. A power injector has been
device that is unable to supply sufficient power to the access point. A power injector has been
configured, but it is for another port. It is likely that the access point has been relocated and has not
configured, but it is for another port. It is likely that the access point has been relocated and has not
been reconfigured for a new power injector.
been reconfigured for a new power injector.
The <  plat
The <
 plat orm
orm name
name > indicates the CDP device detected by the access point. The <
> indicates the CDP device detected by the access point. The <  MAC ad
indicates the MAC address of the CDP device, typically, the switch port.
indicates the MAC address of the CDP device, typically, the switch port.
Note
Note
A Cisco power injector might be required.
A Cisco power injector might be required.
Following the low power status message, two extra messages are displayed when using the console
Following the low power status message, two extra messages are displayed when using the console
port or a Telnet session that identify the actions needed to resolve this low power problem:
port or a Telnet session that identify the actions needed to resolve this low power problem:
1. 1. Verify the required power injector is installed on the new port: <
Verify the required power injector is installed on the new port: <  plat
 port 
 port  > ).
>).
(where <  pla
(where <
 platfor
tform na
m na me
< <  Ethe
 Ethernet
rnet port 
port  > indicates the Ethernet port of the CDP device.
> indicates the Ethernet port of the CDP device.
2. 2. If a power injector is installed, issue the command: power inline negotiation injector installed.
If a power injector is installed, issue the command: power inline negotiation injector installed.
• •
%CDP_PD-2-POWER_LOW: All radios disabled- HIGH_POWER_CLASSIC_NOT_
%CDP_PD-2-POWER_LOW: All radios disabled- HIGH_POWER_CLASSIC_NOT_
CONFIGURED inline power source <
CONFIGURED inline power source <  plat
the access point is in low power mode with all radios disabled and has detected a Cisco switch that
the access point is in low power mode with all radios disabled and has detected a Cisco switch that
does not support Intelligent Power Management, but should be able to supply sufficient power. The
does not support Intelligent Power Management, but should be able to supply sufficient power. The
access point must be configured for pre-standard compatibility.
access point must be configured for pre-standard compatibility.
The<
The<  platform name>
 platform name>  indicates the Cisco platform detected by the access point. The
 indicates the Cisco platform detected by the access point. The <MAC
address>
address>  indicates the MAC address of the switch port.
 indicates the MAC address of the switch port.
Note
Note
You need to upgrade the software on the Cisco switch to support Intelligent Power
You need to upgrade the software on the Cisco switch to support Intelligent Power
Management or configure the access point for pre-standard compatibility.
Management or configure the access point for pre-standard compatibility.
• •
%CDP_PD-4-POWER_OK: Full power - INJECTOR_CONFIGURED_OVERRIDE_SAFETY
%CDP_PD-4-POWER_OK: Full power - INJECTOR_CONFIGURED_OVERRIDE_SAFETY
inline power source —This message indicates the access point has been configured to override the
inline power source —This message indicates the access point has been configured to override the
inline power checks and a power injector is installed.
inline power checks and a power injector is installed.
When using the power inline negotiation injector override
When using the
power inline negotiation injector override command, a power injector must always be
installed to prevent a possible overload condition with an underpowered power source.
installed to prevent a possible overload condition with an underpowered power source.
 
 
 plat form
form name
name > (<
me > indicates the CDP device detected by the access point and
> indicates the CDP device detected by the access point and
 plat form
form name
name > (<
Low Power Condition for Autonomous Access Points
Low Power Condition for Autonomous Access Points
> (<  MAC ad
 MAC address
dress >)—This message
>)—This message
 platform
form name
name > (<
> (<  MAC ad
 MAC address
dress >)—This message indicates
>)—This message indicates
command, a power injector must always be
OL-8369-04
OL-8369-04
 MAC ad dress
dress > >
> (<  Ethe
 Ethernet
rnet
<MAC

Advertisement

Table of Contents
loading

Related Manuals for Cisco Aironet 1130AG Series

Related Products for Cisco Aironet 1130AG Series

Table of Contents