Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Honeywell WICKER PARK
Summary of Contents for Honeywell WICKER PARK
- Page 1 WICKER PARK 48” CEILING FAN MODEL #10268 Español p. 18 Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-361-3883, Monday - Thursday, 8 am - 6 pm, EST and Friday, 8 am - 5 pm, EST.
-
Page 2: Table Of Contents
WELCOME TABLE OF CONTENTS PREPARATION Before beginning the assembly of this product, ensure Care and Maintenance ......2 that all parts are present. -
Page 3: Package Contents
PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: 1. Blade (3) 2. Mounting Bracket 3. Canopy 4. Canopy Cover 5. Yoke Cover 6. Downrod 7. Downrod Clip 8. Downrod Pin 9. Blade Arm (3) 10. -
Page 4: Safety Information
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate, or install the product. • Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit breakers. • Make sure that all electrical connections comply with local codes, ordinances, the National Electrical Code, and ANSI/NFPA 70-199. -
Page 5: Mounting Options
MOUNTING OPTIONS 1. Your fan has 2 mounting options: Fig. 1 • Standard (Fig. 1) • Angle (Fig. 2) Note: The fans in figures 1 and 2 are not the actual fan in your package, they are representation of the 2 different mounting options. -
Page 6: Mounting Bracket Installation
MOUNTING BRACKET INSTALLATION 3. Turn off the circuit breakers and wall switch leading Fig. 3 to the fan wire leads (Fig. 3). WARNING Failure to disconnect the power supply prior to installation may result in serious injury or death. 4. Loosen all four mounting bracket screws and Fig. -
Page 7: Standard Or Angle Mounting Instructions
STANDARD OR ANGLE MOUNTING INSTRUCTIONS 6. Partially loosen the set screws in the yoke of the Fig. 6 motor assembly (Fig. 6). Set Screw Fig. 7 7. Remove the downrod clip and downrod pin from the downrod (Fig. 7). Downrod Clip Downrod Pin Downrod... - Page 8 STANDARD OR ANGLE MOUNTING INSTRUCTIONS 9. Slide the downrod into the yoke of the motor Fig. 9 assembly, align the holes, and reinstall the Downrod downrod pin and downrod clip. Then re-tighten the set screws with a Phillips screwdriver (Fig. 9). Downrod Downrod Clip...
- Page 9 STANDARD OR ANGLE MOUNTING INSTRUCTIONS 12. Remove the six motor screws from the top of the Fig. 12 motor assembly and keep for blade attachment (Fig. 12). Motor Screw with Washer Motor Screw with Washer 13. Install the ball end of the downrod into the Fig.
-
Page 10: Wiring
WIRING CAUTION Fig. 14 Be sure outlet box is properly grounded or that a ground (green or bare) wire is present. Black (Hot) WARNING If house wires are different colors than referred to in White (Neutral) the following steps, consult a professional electrician Bare/Green (Ground) to determine wiring. -
Page 11: Canopy Installation
CANOPY INSTALLATION 16. Lift the canopy up so the partially installed mounting Fig. 16 bracket screws engage the J-slots on each side of the canopy. Rotate the canopy clockwise and install the previously removed mounting bracket screws from Step 4. Tighten all four screws with a Phillips screwdriver (Fig. -
Page 12: Blade Installation
BLADE INSTALLATION 17. Insert the blade screw with blade washer Fig. 17 through the blade arm, blade and into the screw Blade Arm Blade cap. Tighten each blade screw with a Phillips Screw screwdriver (not included) starting with the one Blade Washer in the middle. -
Page 13: Light Kit Installation
LIGHT KIT INSTALLATION 19. Remove the pre-assembled fitter plate screws from Fig. 19 the fitter plate. Connect the 9-pin connector from the fan to the 9-pin connector to the light kit. Fitter Plate Then, lift the light kit over the fitter plate and Screw secure the light kit to the fitter plate using the three 9-pin Connector... -
Page 14: Operating Instructions
OPERATING INSTRUCTIONS 22. Use the reverse switch, located on the side of the Fig. 22 switch housing, to optimize your fan for seasonal performance (Fig. 22). Using a ceiling fan will allow you to raise your thermostat in the summer and lower your thermostat in the winter without sacrificing comfort. -
Page 15: Replacement Parts List
REPLACEMENT PARTS LIST For replacement parts, call the customer service department at 1-877-361-3883, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday. MODEL 10268 PIECE DESCRIPTION PART # Blade Arm 10268-A Blade 10268-B Hardware bag (not shown) contains: Mounting hardware, blade attachment hardware,... -
Page 16: Troubleshooting
TROUBLESHOOTING At least twice each year, lower the canopy to check the downrod assembly, and then tighten all screws on the fan. Clean the motor housing with only a soft brush or lint-free cloth to avoid scratching the finish. Clean the blades with a lint-free cloth. You may occasionally apply a light coat of furniture polish to wood blades for added protection. -
Page 17: Limited Lifetime Warranty
1-877-361-3883 Monday - Thursday, 8 am - 6 pm, EST and Friday, 8 am - 5 pm, EST. Please have a copy of the receipt as proof of purchase. The Honeywell Trademark is used under license from Honeywell International Hong Kong China Electric Appliance Manufacture Co., Ltd.