Table of Contents
Related Manuals for Cisco Meraki MR70
Summary of Contents for Cisco Meraki MR70
- Page 1 The Cisco Meraki MR70 is a dual-band enterprise class 802.11ac cloud-managed access point Package Contents The MR70 package contains the following: • MR70 Cloud-Managed Access Point • Mount cradle including built-in level tool...
- Page 2 • Mount Kit Wall screws and wall screw anchors Understanding the MR70 Your Meraki MR70 has the following features:...
-
Page 3: Ethernet Ports
The mount cradle has the following features: Ethernet Ports... - Page 4 The MR70 features a Gigabit Ethernet RJ45 port that accepts 802.3at and 802.3af power (labeled “Eth0, PoE”). This port should be used for uplink to your WAN connection. Power Source Options The MR70 access point can be powered using either the Meraki AC Adapter, PoE Injector (both sold separately), or a third-party PoE switch.
- Page 5 Check and Upgrade Firmware To ensure your MR70 performs optimally immediately following installation, it is recommended that you facilitate a firmware upgrade prior to mounting your MR70. 1. Attach your MR70 to power and a wired Internet connection. See the "Power the MR70"...
-
Page 6: Collect Tools
4. Click on the “Uplink Configuration” tab. Log in. The default login is the serial number (e.g. Qxxx-xxxx-xxxx), with no password (e.g., Q2DD-551C-ZYW3). 5. Configure the static IP address, net mask, gateway IP address and DNS servers that this AP will use on its wired connection. 6. -
Page 7: Choose Your Mounting Location
2. Power over Ethernet supports a maximum cable length of 300 ft (100 m). 3. If being used in a mesh deployment, the MR70 should have line of sight to at least two other Meraki devices. A Cisco Partner can help ensure that your AP placement is ideal. - Page 8 To attach the MR70 to the mount cradle properly, line up the top edge of the AP with the top tab of the mount cradle. Since the cradle is already mounted to the wall, guide the MR70 towards the top tab and insert the top tab into the MR70’s slot. Then adjust the MR70 to guide the MR70’s bottom slot into the cradle’s bottom tab until it clicks into place.
- Page 9 To release the MR70 from the mount cradle, first remove the security screw that secures the MR70 to the cradle’s bottom tab. While holding the MR70 with one hand, press the cradle’s bottom tab upwards, releasing the MR70 from the bottom of the cradle. Then remove the MR70 from the cradle’s top tab.
- Page 10 b. Note: Your MR70 must have an active route to the Internet to check and upgrade its firmware. 2. Verify access point connectivity a. Use any 802.11 client device to connect to the MR70 and verify proper connectivity using the client’s web browser. 3.
- Page 11 • Consult the dealer or an experienced radio/TV technician for help. FCC Caution Any changes or modifications no expressly approved by Meraki could void the user’s authority to operate this equipment. This Transmitter must not be co-located or operation in conjunction with any other antenna or transmitter.
- Page 12 (i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; (ii) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.